LifeTrac II Fabrication Procedure: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
No edit summary
No edit summary
 
(5 intermediate revisions by the same user not shown)
Line 5: Line 5:
Key - (V) = Vertical. (E,W) = East,West. (N,S) = North South.
Key - (V) = Vertical. (E,W) = East,West. (N,S) = North South.


13/16" brill bit used for 3/4" bolts.
13/16" drill bit used for 3/4" bolts.
 
*[4] 92"×4"×4" Tubes for base.
*[4] 92"×4"×4" Tubes for base.
**[2] outer base tubes - 13/16" (V)holes 2" from ends. 1 (V)hole 4" front of centre. 4 (E,W)holes for wheel plates 9" & 13" from ends. 2 (V)holes for hydraulic base plate 13-1/4" & 22-3/4" behind centre, 1-1/4" from outer edge.  
**[2] Outer base tubes - 13/16" (V)holes 2" from ends. (V)holes 4" front of centres. (E,W)holes for wheel plates 9" & 13" from ends. (V)holes for hydraulic base plate 13-1/4" & 22-3/4" behind centres, 1-1/4" from outer edges.  
**[2] inner base tubes - (V)holes 2" form ends. (V)hole 4" front of centre. (E,W)holes 6", 9" & 13" from ends & 1 (E,W)hole in centre. 2 (V)holes for hydraulic base plate 13-1/4" & 22-3/4" behind centre, 1-1/4" from inner edge.
**[2] Inner base tubes - (V)holes 2" form ends. (V)hole 4" front of centres. (E,W)holes 6", 9" & 13" from ends & (E,W)holes in centres. (V)holes for hydraulic base plate 13-1/4" & 22-3/4" behind centres, 1-1/4" from inner edges.


*[3] 60" Under base tubes.
*[3] 60" Under base tubes.
Line 14: Line 15:
**(N,S)holes 14" form ends.
**(N,S)holes 14" form ends.


*[2] 55" front vertical tubes.
*[2] 55" Front vertical tubes.
**(E,W)holes 2" form top & 2", 6" & 9" from bottom.
**(E,W)holes 2" form tops & 2", 6" & 9" from bottoms.
**(N,S)holes 6" from top & 5" from bottom.
**(N,S)holes 6" from tops & 5" from bottoms.
 
*[2] 52" Centre vertical tubes.
**(E,W)holes 2" from tops & 6" from bottoms.
**(N,S)holes 6" from tops & 2" from bottoms.
 
*[2] 59" Rear vertical tubes.
**(E,W)holes 6" from tops & 2", 6" & 9" from bottoms.
**(N,S)holes 2" from tops & 5" from bottoms.
 
*[3] 44" Top (overhead E,W) tubes.
**(V)holes 2" from ends.
**(N,S)holes 6" from ends.


*[2] 52" centre vertical tubes.
*[2] 84" Top (overhead N,S) tubes.
**(E,W)holes 2" from top & 6" from bottom.
**(E,W)holes 2" from ends & in centres.
**(N,S)holes 6" from top & 2" from bottom
**(v)holes 6" from ends & 4" from of centres.




[[Category:LifeTrac II]]
[[Category:LifeTrac II]]

Latest revision as of 22:58, 3 July 2010

Frame

As a general rule, all the measurements I have listed here will be more accurate if you mark the centre of each tube and then measure the "holes" from the centre out as opposed to from the ends in, in case some tubes are not cut to the exact lengths.

Key - (V) = Vertical. (E,W) = East,West. (N,S) = North South.

13/16" drill bit used for 3/4" bolts.

  • [4] 92"×4"×4" Tubes for base.
    • [2] Outer base tubes - 13/16" (V)holes 2" from ends. (V)holes 4" front of centres. (E,W)holes for wheel plates 9" & 13" from ends. (V)holes for hydraulic base plate 13-1/4" & 22-3/4" behind centres, 1-1/4" from outer edges.
    • [2] Inner base tubes - (V)holes 2" form ends. (V)hole 4" front of centres. (E,W)holes 6", 9" & 13" from ends & (E,W)holes in centres. (V)holes for hydraulic base plate 13-1/4" & 22-3/4" behind centres, 1-1/4" from inner edges.
  • [3] 60" Under base tubes.
    • (V)holes 2" & 10" from ends.
    • (N,S)holes 14" form ends.
  • [2] 55" Front vertical tubes.
    • (E,W)holes 2" form tops & 2", 6" & 9" from bottoms.
    • (N,S)holes 6" from tops & 5" from bottoms.
  • [2] 52" Centre vertical tubes.
    • (E,W)holes 2" from tops & 6" from bottoms.
    • (N,S)holes 6" from tops & 2" from bottoms.
  • [2] 59" Rear vertical tubes.
    • (E,W)holes 6" from tops & 2", 6" & 9" from bottoms.
    • (N,S)holes 2" from tops & 5" from bottoms.
  • [3] 44" Top (overhead E,W) tubes.
    • (V)holes 2" from ends.
    • (N,S)holes 6" from ends.
  • [2] 84" Top (overhead N,S) tubes.
    • (E,W)holes 2" from ends & in centres.
    • (v)holes 6" from ends & 4" from of centres.
Retrieved from "https://wiki.opensourceecology.org/index.php?title=LifeTrac_II_Fabrication_Procedure&oldid=12726"