Torch Table Xaxis: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
No edit summary
No edit summary
 
(3 intermediate revisions by 2 users not shown)
Line 1: Line 1:
=Bill of Materials X Axis=
{{Category=Torch Table}}
{| {{table}}
=Bill of Materials=
{|border="1" {{table}}
| align="center" style="background:#f0f0f0;"|'''Item'''
| align="center" style="background:#f0f0f0;"|'''Item'''
| align="center" style="background:#f0f0f0;"|'''Discription'''
| align="center" style="background:#f0f0f0;"|'''Discription'''
Line 8: Line 9:
| align="center" style="background:#f0f0f0;"|'''Purpose'''
| align="center" style="background:#f0f0f0;"|'''Purpose'''
| align="center" style="background:#f0f0f0;"|'''Aquired?'''
| align="center" style="background:#f0f0f0;"|'''Aquired?'''
|-
|----
| Bearing R6-2RS 3/8\"x7/8\"x9/32\" Sealed||10 pack||4||$14.95 ||VXB Part Number: Kit711||For preventing the carrage from jumping the track||no
|Bearing R6-2RS 3/8"x7/8"x9/32" Sealed
|-
|10 pack
| V-Groove Bearings 3/8 inch||single pack||4||9.95||VXB V-Groove bearings Part number: Kit8407||To provide low friction linear motion||no
|4
|-
|$14.95  
| 3/8 inch Hard Fiber Washers||Pack of 100||16||2.5||McMaster Part Number: 95601A330||Holding bearings||no
|VXB Part Number: Kit711
|-
|For preventing the carrage from jumping the track
| Hot rolled steel 3\"x1/8\" plate||10.0 Ft.||24.75||12.7||Metalsdepot||To provide material for motor mounts||no
|no
|-
|----
| Hot rolled steel 1\"x1\" square tubes 16 gauge||24ft for $23.28||420||23.28||Metalsdepot||To provide structural support||no
|V-Groove Bearings 3/8 inch
|-
|single pack
| Gear Rack  (1/2” sq. x 72” 20 DP 20 Deg)||6 feet per rack||10||24.8||Standard Steel Specialty Part Number: 200011||rack for gear to ride on||no
|4
|-
|9.95
| 3 x 1/8 inch cold rolled Plate||6.0 Ft.||20||17.28||Metalsdepot||To provide material to make rails||no
|VXB V-Groove bearings Part number: Kit8407
|-
|To provide low friction linear motion
| \"3/8 inch threaded rod, Overall Length
|no
|-
|----
| 36\"\"\"|| Each||57.2||$2 ||McMaster Part Number:  98837A031||for connecting the top and bottom carage||no
|3/8 inch Hard Fiber Washers
|-
|Pack of 100
| 3/8 inch nuts||Pack of 100||48||4.2||Part Number: 90473A031||For locking threaded rod in place||no
|16
|-
|2.5
| 3/8 inch washers||Pack of 140||48||3.23||Part Number: 90126A031||For locking nuts and for spacers||no
|McMaster Part Number: 95601A330
|-
|Holding bearings
| Steel 20 Deg Pressure Angle Spur Gear 20 Pitch, 20 Teeth, 1\" Pitch Dia, 1/2\" Bore||Each||2||15.37||McMaster Part Number: 5172T12||Attaches to stepper motors and interfaces with gear rack||no
|no
|-
|----
| sleeve bearing||Each||2||1.34||McMaster Part Number: 6391K143||to connect between the stepper motor and the gear, will also add a bit of adjustable length||no
|Hot rolled steel 3"x1/8" plate
|-
|10.0 Ft.
| 10-32 set screw 7/16\"||per Pack of 100||2||5.44||Part Number: 92311A428||Set screw for attaching spur gear, sleeve bearing to stepper shaft||no
|2.83 ft
|-
|12.7
| 10 gauge bolts|| Pack of 50||52||7.78||McMaster Part Number: 92610A245||stepper||no
|Metalsdepot
|-
|To provide material for motor mounts
| 10 gauge nuts||Pack of 100||58||1.54||McMaster Part Number: 90480A011||stepper||no
|no
|-
|----
| Zinc-Pltd Stl Pan Head Phillips Machine Screw 1/4\"-20 Thread, 1-1/2\" Length||Pack of 100||8||10.75||McMaster Part Number:  90272A546||Connects the mount plate arms to the carrage||no
|Hot rolled steel 1"x1" square tubes 16 gauge
|-
|24ft for $23.28
| Zinc & Yellow Plated Grade 8 Steel Hex Nut 1/4\"-20 Thread Size, 7/16\" Width, 7/32\" Height||Packs of 100||16||3.06||McMaster Part Number: 94895A029||For locking the mount plate swing tightness||no
|35.00 ft
|-
|23.28
| 1/4 inch Nylon Thrust Bearing||Each||8||1.05||McMaster Part Number: 2797T1||allows the motor to swing freely||no
|Metalsdepot
|-
|To provide structural support
| stepper spring||pack of 6||2||10||McMaster Part Number: 3114T79||Prevents stepper motor shaft from crunching ||no
|no
|-
|----
|
|Gear Rack  (1/2” sq. x 72” 20 DP 20 Deg)
|6 feet per rack
|20.00 ft
|24.8
|Standard Steel Specialty Part Number: 200011
|rack for gear to ride on
|no
|----
|3 x 1/8 inch cold rolled Plate
|6.0 Ft.
|20.00 ft
|17.28
|Metalsdepot
|To provide material to make rails
|no
|----
|3/8 inch threaded rod, Overall Length 36"
| Each
|4.77 ft
|$2  
|McMaster Part Number:  98837A031
|for connecting the top and bottom carage
|no
|----
|3/8 inch nuts
|Pack of 100
|48
|4.2
|Part Number: 90473A031
|For locking threaded rod in place
|no
|----
|3/8 inch washers
|Pack of 140
|48
|3.23
|Part Number: 90126A031
|For locking nuts and for spacers
|no
|----
|Steel 20 Deg Pressure Angle Spur Gear 20 Pitch, 20 Teeth, 1" Pitch Dia, 1/2" Bore
|Each
|2
|15.37
|McMaster Part Number: 5172T12
|Attaches to stepper motors and interfaces with gear rack
|no
|----
|sleeve bearing
|Each
|2
|1.34
|McMaster Part Number: 6391K143
|to connect between the stepper motor and the gear, will also add a bit of adjustable length
|no
|----
|10-32 set screw 7/16"
|per Pack of 100
|2
|5.44
|Part Number: 92311A428
|Set screw for attaching spur gear, sleeve bearing to stepper shaft
|no
|----
|Zinc-Pltd Stl Pan Head Phillips Machine Screw 10-32 Thread, 1-3/4" Length
| Pack of 100
|4
|8.45
|McMaster Part Number: 90272A837
|Connects the mount plate arms to the carrage
|no
|----
|Zinc-Pltd Stl Pan Head Phillips Machine Screw 10-32 Thread, 2-1/2" Length
|Pack of 100
|30
|6.58
|McMaster Part Number: 90272A840
|For connecting the rail, rack, spacer and c channel
|no
|----
|Zinc-Pltd Stl Pan Head Phillips Machine Screw 10-32 Thread, 3/4" Length
|Pack of 100
|12
|5.11
|McMaster Part Number:  90272A831
|Connects the mount plate arms to the carrage
|no
|----
|Zinc-Plated Steel Machine Screw Hex Nut 10-32 Thread Size, 3/8" Width, 1/8" Height
|Packs of 100
|46
|1.55
|McMaster Part Number: 90480A195
|For locking the mount plate swing tightness, tightening the rack and locking the stepper motor in place
|no
|----
|Nylon 6/6 General Purpose Flat Washer Off-White, No. 10 Screw Sz, .44" OD,.02"-.04" Thk
|per Pack of 100
|16
|3.83
|Part Number: 90295A120
|allows the motor to swing freely
|no
|----
|stepper spring
|pack of 6
|2
|10
|McMaster Part Number: 3114T79
|Prevents stepper motor shaft from crunching  
|no
|----
|}
|}

Latest revision as of 18:39, 9 February 2011

Main > Digital Fabrication > RepLab Tools > Torch Table

Bill of Materials

| align="center" style="background:#f0f0f0;"|Item | align="center" style="background:#f0f0f0;"|Discription | align="center" style="background:#f0f0f0;"|Amount | align="center" style="background:#f0f0f0;"|Cost per item | align="center" style="background:#f0f0f0;"|Further Info | align="center" style="background:#f0f0f0;"|Purpose | align="center" style="background:#f0f0f0;"|Aquired? |---- |Bearing R6-2RS 3/8"x7/8"x9/32" Sealed |10 pack |4 |$14.95 |VXB Part Number: Kit711 |For preventing the carrage from jumping the track |no |---- |V-Groove Bearings 3/8 inch |single pack |4 |9.95 |VXB V-Groove bearings Part number: Kit8407 |To provide low friction linear motion |no |---- |3/8 inch Hard Fiber Washers |Pack of 100 |16 |2.5 |McMaster Part Number: 95601A330 |Holding bearings |no |---- |Hot rolled steel 3"x1/8" plate |10.0 Ft. |2.83 ft |12.7 |Metalsdepot |To provide material for motor mounts |no |---- |Hot rolled steel 1"x1" square tubes 16 gauge |24ft for $23.28 |35.00 ft |23.28 |Metalsdepot |To provide structural support |no |---- |Gear Rack (1/2” sq. x 72” 20 DP 20 Deg) |6 feet per rack |20.00 ft |24.8 |Standard Steel Specialty Part Number: 200011 |rack for gear to ride on |no |---- |3 x 1/8 inch cold rolled Plate |6.0 Ft. |20.00 ft |17.28 |Metalsdepot |To provide material to make rails |no |---- |3/8 inch threaded rod, Overall Length 36" | Each |4.77 ft |$2 |McMaster Part Number: 98837A031 |for connecting the top and bottom carage |no |---- |3/8 inch nuts |Pack of 100 |48 |4.2 |Part Number: 90473A031 |For locking threaded rod in place |no |---- |3/8 inch washers |Pack of 140 |48 |3.23 |Part Number: 90126A031 |For locking nuts and for spacers |no |---- |Steel 20 Deg Pressure Angle Spur Gear 20 Pitch, 20 Teeth, 1" Pitch Dia, 1/2" Bore |Each |2 |15.37 |McMaster Part Number: 5172T12 |Attaches to stepper motors and interfaces with gear rack |no |---- |sleeve bearing |Each |2 |1.34 |McMaster Part Number: 6391K143 |to connect between the stepper motor and the gear, will also add a bit of adjustable length |no |---- |10-32 set screw 7/16" |per Pack of 100 |2 |5.44 |Part Number: 92311A428 |Set screw for attaching spur gear, sleeve bearing to stepper shaft |no |---- |Zinc-Pltd Stl Pan Head Phillips Machine Screw 10-32 Thread, 1-3/4" Length | Pack of 100 |4 |8.45 |McMaster Part Number: 90272A837 |Connects the mount plate arms to the carrage |no |---- |Zinc-Pltd Stl Pan Head Phillips Machine Screw 10-32 Thread, 2-1/2" Length |Pack of 100 |30 |6.58 |McMaster Part Number: 90272A840 |For connecting the rail, rack, spacer and c channel |no |---- |Zinc-Pltd Stl Pan Head Phillips Machine Screw 10-32 Thread, 3/4" Length |Pack of 100 |12 |5.11 |McMaster Part Number: 90272A831 |Connects the mount plate arms to the carrage |no |---- |Zinc-Plated Steel Machine Screw Hex Nut 10-32 Thread Size, 3/8" Width, 1/8" Height |Packs of 100 |46 |1.55 |McMaster Part Number: 90480A195 |For locking the mount plate swing tightness, tightening the rack and locking the stepper motor in place |no |---- |Nylon 6/6 General Purpose Flat Washer Off-White, No. 10 Screw Sz, .44" OD,.02"-.04" Thk |per Pack of 100 |16 |3.83 |Part Number: 90295A120 |allows the motor to swing freely |no |---- |stepper spring |pack of 6 |2 |10 |McMaster Part Number: 3114T79 |Prevents stepper motor shaft from crunching |no |---- |}

Retrieved from "https://wiki.opensourceecology.org/index.php?title=Torch_Table_Xaxis&oldid=18040"