Torch Table Intro: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
(Redirected page to CNC Torch Table)
 
(79 intermediate revisions by 10 users not shown)
Line 1: Line 1:
=Torch Table Design=
#redirect [[CNC Torch Table]]
 
 
Our development log [http://openfarmtech.org/index.php?title=XYZ here.]
 
Here is an updated design schematic for a torch table. The drive is obtained with stepper motors and rack-and-pinion style direct drive with a 2" pulley. Linear bearings and ball screws were replaced with rack-and-pinion drive due to cost considerations.
 
Notable design goals:
*1/32" accuracy is sought for general acetylene torch cutting (or plasma cutter) applications
*Ball bearings ride directly on structural steel surface
*Direct coupling of stepper motor to rack belting via a single pulley; no gearing pulleys involved
**Stepper motor speed: 10 RPM for ~60 inch per minute (IPM) motion with ~2 inch diameter pulley
**Fast rapid motion should be possible, 50 RPM for 300 IPM
*Traction of rack-and-pinion drive is obtained via the weight of the gantry
**Gantry weight: 20-30 lb
**Lowest bearings in diagram below provide additional clamping in the Z direction, if needed
*Frame is 6" wide U-channel, 7/16" thick
*4'x8'x1' working object dimensions
 
----
[[Image:XYZ_table_drive.jpg]]
----
 
Y axis drive detail:
 
*Y axis motion is on a 1 1/4"x1/8" square tube as the rail, with a surrounding, telescoping 4"x6"x1/8" tube:
**Two telescoping tubes with bearings between them on all 4 sides function as a low-tech linear bearing
*4 foot working object width
----
[[Image:y axis detail.jpg]]
----
 
Z axis detail:
*1 foot working object height
*Simple 1/4" threaded rod for drive
 
----
[[Image:z axis detail.jpg]]
----
 
=XYZ Table Preliminary Design=
 
The specifications development for a robust and scaleable machine is under development [http://openfarmtech.org/index.php?title=XYZ_Table here]. The prototype specifications for a torch table application will be developed on this page.
 
The basic design follows.
 
Using ball screws and linear bearings appears to be the easiest method. Present research indicates that profile guide rails are twice as cheap for the accuracy required, so this will be redesigned.
 
[[Image:XYZ_Design_rationale2.jpg]]
 
Compare this to [http://www.torchmate.com/industrial/index.htm gear drive and linear rails], which appears to be more complicated in terms of drive components.
 
=Bill of Materials=
 
 
Details:
 
Rack from [http://www.stdsteel.com/gear.htm Standard Steel Specialties].
 
=Development Evolution=
This section shows other options considered.
 
==Torch Table Implementation==
 
Specifications:
*.01 inch accuracy
*Precision acme rod
*Profile rail guides
Motors: [http://www.xylotex.com/StepperMotor.htm]
*Nema 23 Double Stack/Double Shaft Bipolar Stepper Motor, Flats ground on each end
*269 inch lb holding torque on main axis
*Rated Current - 2.8A/phase
*Shaft width - .25 inch
Controller:
*
 
*Direct coupling to precision acme rod
 
==Bill of Materials for a Simple Prototype==
 
*It appears that the Xylotex drive is applicable to large torch tables. [http://www.kickassmachinesinc.com/ Here is one] that Xylotex told me uses their controllers and motors.
**$425 for motors and controllers
*Ball screw [http://www.mcmaster.com/ 5966K26] at McMaster Carr, $1.26/inch, and $25 for each ball nut - $125 per 6 foot run
**90% mechanical efficiency compared to 30% for acme screw
[[Image:ballscrew.gif]] [[Image:ballnut.gif]]
**$250 for x axis if 2 screws, $125 for y axis (1 screw), $50 for z axis
**End blocks are extra
 
Here is a parts list:
 
 
*Compare [http://www.xylotex.com/425ozin.htm 425 in oz motors] to [269 in oz motors].
*Compare [http://www.xylotex.com/4AxSysKit-425.htm 4 axis kit, $400].
*See [http://www.solsylva.com/cnc/acme.html discussion] on threaded rod vs. acme and precision acme.
*Good discussion on drive options from [http://www.solsylva.com/cnc/beltdrive.html Solsylva]
 
==Instructables References==
Search Instructables.com for CNC projects. There is a load. The people should be tapped for review. Just sign up and send authors an email.
*http://www.instructables.com/id/SDPT6W9F3HY3SLR/
**CNCZone hath lots of DIY implementations - [http://www.cnczone.com/forums/forumdisplay.php?f=48]
*http://www.instructables.com/id/3-Axis-CNC-Router---60x60x5---JunkBot/
**[http://www.solsylva.com/ Solsylva] has plans for 3 axis tables, 2'x5' for the largest
 
==ShopBot==
*[http://www.shopbottools.com/prSalpha.htm ShopBot table]
 
==Rack and Pinion Calculations==
 
An interesting, low cost positioning system for low precision (0.01") machining (such as acetylene torch tables) consists of belt-drive rack and pinion.
 
Calculations:
*Typical motors have 0-1000 RPM and 200 steps
*A drive pinion of 1 inche diameter means 3 inch/200 = 15/1000 of an inch step resolution
*For a 2 inch drive wheel (recommended), this is  3/100 resolution, which is sufficient
**We need only 1/16 resolution, and we have twice that resolution with this system
 
Look for parts to match:
*McMaster Carr part 6486K129 - 20 mm wide, 280 cm long (9+ feet) Power Grip belts - $52.50
**2.2 inch drive wheel - $43, would give 35/1000 step resolution
*McMaster Carr - item 7959K29, 3/4 inch rack-and pinion type belting, $5.69/foot - $32 for 9 feet
*Or, part # 7959K26, 1/2 inch belting, 3/8 inch pitch, high torque applications, $3.59/foot
**Part 6495K15 is pulley, $20 for 2.1" pulley.
 
==Timing Belt Data==
*[http://motion-controls.globalspec.com/datasheets/217/QualityTransmissionComponents/9FBE4A84-A3A4-477E-A4ED-65157425ADD7] has strength of .375 pitch, 1/2" belt as 675 lbf/in breaking strength - neoprene, nylon covered.
*MXL .08 pitch, 1/4 inch wide belt (McMaster Carr part #1375K39) has accuracy of 1/2000. Uses 20 tooth pulley, .5" diameter
**1.6" circumference/200 steps would be 80/1000 accuracy
*Proposed .375 pitch belt has 1.9 diameter pulley of 16 teeth
**1/200 of 1.9*pi - this yields 1/30" accuracy for full steps. I may want to set for up to 1/8 microstepping.

Latest revision as of 06:43, 25 August 2011

Redirect to:

Retrieved from "https://wiki.opensourceecology.org/index.php?title=Torch_Table_Intro&oldid=37269"