|
|
| (20 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| =Block Uniformity= | | =Assemblies= |
| | |
| *Keep 2 block dimensions same for all blocks
| |
| | |
| *Based on the conceptual design, 1 of the block dimensions will solely be used to fit the diameter of the leadscrews, precision shafts, and sleeve bearings.
| |
| | |
| *The other block dimension to be uniform will mostly support the part by its length on precision shafts.
| |
| | |
| *For accommodating leadscrew nuts up to 10mm or 3/8" dia, dimension 1 will be 40mm (approx. 1.5")
| |
| | |
| *For accommodating stepper motor mounting and axis stability, dimension 2 will be 75mm (approx. 3")
| |
| | |
| =Stepper Motor Mount Uniformity=
| |
| | |
| *Use the same stepper motor type for each axis.
| |
| | |
| *Nema 17 steppers for appropriate performance characteristics.
| |
| | |
| *Standard 31mm center-to-center mounting holes. Modular.
| |
| | |
| =Sleeve Bearing Mount Uniformity=
| |
| | |
| *Use the same sleeve bearing type throughout machine
| |
| | |
| *2 fastening holes on the part to which sleeve bearing should be mounted. For sleeve bearing of 24mm diameter, mount circle with M5 screws and 1mm clearance should be 24 + 5 + 2 = 31mm diameter.
| |
| | |
| *20mm depth mount holes
| |
| | |
| =Leadscrew Nut Mount Uniformity=
| |
| | |
| *Use the same leadscrew nut throughout machine
| |
| | |
| *3 fastening holes on the part for the nut mounting. For current leadscrew nut, insertion diameter = 12.7mm, mount circle diameter = 19.05mm.
| |
| | |
| *20mm depth mount holes
| |
| | |
| =X Blocks=
| |
| | |
| *The X major and minor blocks should have the same heights.
| |
| | |
| *Base to shaft hole = 30mm
| |
| | |
| *Base to stepper hole = 75mm
| |
| | |
| *Base to top = 100mm
| |
| | |
| *Side to mount holes = 10mm
| |
| | |
| =Y Blocks=
| |
| | |
| *The Y major and minor blocks should have the same heights.
| |
| | |
| *Base to X shaft hole = 25mm
| |
| | |
| *Base to Y lower shaft hole = 50mm
| |
| | |
| *Base to X stepper hole = 70mm
| |
| | |
| *Base to Y stepper hole = 95mm
| |
| | |
| *Base to Y upper shaft hole = 140mm
| |
| | |
| *Base to top = 150mm
| |
| | |
| =Z Blocks=
| |
| | |
| *The Z mount block should coincide with the Y shaft positions.
| |
| | |
| *Base to lower shaft hole = 25mm
| |
| | |
| *Base to stepper hole = 70mm
| |
| | |
| *Base to upper shaft hole = 115mm
| |
| | |
| *Base to top = 140mm
| |
| | |
| *The Z major and minor blocks should have the same shaft and stepper holes.
| |
| | |
| *Z major/minor thickness and width = 10mm x 85mm
| |
| | |
| *Side A to close shaft hole = 10mm
| |
| | |
| *Side A to stepper hole = 55mm
| |
| | |
| *Side A to far shaft hole = 100mm
| |
| | |
| *Side A to Side B = 110mm
| |
| | |
| =End Block=
| |
| | |
| *Side A to close shaft hole = 25mm
| |
| | |
| *Side A to stepper hole = 70mm
| |
| | |
| *Side A to far shaft hole = 115mm
| |
| | |
| *Side A to Side B = 140mm
| |
| | |
| =Assembly=
| |
|
| |
|
| *[[Image: CNCCMV2.jpg|500px]] | | *[[Image: CNCCMV2.jpg|500px]] |
|
| |
|
| =Structure: Platform=
| | *[[Image: CNCV2XAxis.jpg|500px]] |
| | |
| *[[File: PlatformV2.pdf]]
| |
| | |
| *[[File: PlatformV2.stp]]
| |
| | |
| =Structure: X Major Block=
| |
| | |
| *[[File: XMajorBlockV2.pdf]]
| |
| | |
| *[[File: XMajorBlockV2.stp]]
| |
| | |
| =Structure: X Minor Block=
| |
| | |
| *[[File: XMinorBlockV2.pdf]]
| |
| | |
| *[[File: XMinorBlockV2.stp]]
| |
| | |
| =Structure: Y Major Block=
| |
| | |
| *[[File: YMajorBlockV2.pdf]]
| |
| | |
| *[[File: YMajorBlockV2.stp]]
| |
| | |
| =Structure: Y Minor Block=
| |
| | |
| *[[File: YMinorBlockV2.pdf]]
| |
| | |
| *[[File: YMinorBlockV2.stp]]
| |
| | |
| =Structure: Z Mount Block=
| |
| | |
| *[[File: ZMountBlockV2.pdf]]
| |
| | |
| *[[File: ZMountBlockV2.stp]]
| |
| | |
| =Structure: Z Major Block=
| |
| | |
| *[[File: ZMajorBlockV2.pdf]]
| |
| | |
| *[[File: ZMajorBlockV2.stp]]
| |
| | |
| =Structure: Z Minor Block=
| |
| | |
| *[[File: ZMinorBlockV2.pdf]]
| |
| | |
| *[[File: ZMinorBlockV2.stp]]
| |
| | |
| =Structure: End Mount Block=
| |
| | |
| *[[File: EndMountBlockV2.pdf]]
| |
| | |
| *[[File: EndMountBlockV2.stp]]
| |
| | |
| =Structure: Spindle Block=
| |
| | |
| *[[File: SpindleBlockV2.pdf]]
| |
| | |
| *[[File: SpindleBlockV2.stp]]
| |
| | |
| =Bearings: Sleeve Bearing=
| |
| | |
| *[[File: SleeveBearingV2.pdf]]
| |
| | |
| *[[File: SleeveBearingV2.stp]]
| |
| | |
| =Bearings: Ball Bearing=
| |
| | |
| =Drive: Leadscrew=
| |
| | |
| =Drive: Leadscrew Nut=
| |
| | |
| =Drive: Stepper Motor=
| |
| | |
| *[[File: 42BYGH404.pdf]] | |
|
| |
|
| =Shafts: XY Shaft= | | =Manufacturing= |
|
| |
|
| *[[File: XYShaftV2.pdf]]
| | [http://opensourceecology.org/wiki/CNCCMV2/CAD/Templates Templates] |
|
| |
|
| *[[File: XYShaftV2.stp]]
| | =Parts= |
|
| |
|
| =Shafts: Z Shaft=
| | [http://opensourceecology.org/wiki/CNCCMV2/CAD/Structure Structure] |
|
| |
|
| *[[File: ZShaftV2.pdf]]
| | [http://opensourceecology.org/wiki/CNCCMV2/CAD/Shafts Shafts] |
|
| |
|
| *[[File: ZShaftV2.stp]]
| | [http://opensourceecology.org/wiki/CNCCMV2/CAD/CollarsCouplings Collars and Couplings] |
|
| |
|
| =Shafts: Spindle Shaft=
| | [http://opensourceecology.org/wiki/CNCCMV2/CAD/Bearings Bearings] |
|
| |
|
| *[[File: SpindleShaft.pdf]]
| | [http://opensourceecology.org/wiki/CNCCMV2/CAD/Fasteners Fasteners] |
|
| |
|
| *[[File: SpindleShaft.stp]]
| | [http://opensourceecology.org/wiki/CNCCMV2/CAD/Drive Drive] |
