|
|
| (23 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| =Concepts= | | =Basic Concept= |
|
| |
|
| [http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Rationale/Basic_Concept Basic Concept]
| | http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Rationale/Basic_Concept |
|
| |
|
| [http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Rationale/Blade_Rotation_System Blade Rotation System]
| | =Industry Standards= |
|
| |
|
| [http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Rationale/Movement_System Movement System]
| | http://opensourceecology.org/wiki/Cold_Saw/Industry_Standards_Analysis |
|
| |
|
| [http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Rationale/Hold_System Hold System]
| | =Systems Engineering Breakdown Diagram= |
|
| |
|
| =Feature: Swivel Head=
| | http://opensourceecology.org/wiki/Cold_Saw/V1_Systems_Engineering_Breakdown_Diagram |
| | |
| *'''Swivel Head''' (to allow angled cuts)
| |
| | |
| [[Image: ColdSawV1SwvHead.png]]
| |
| | |
| Notes: The swivel clamp fastener should be mounted such that the swivel plate is horizontally clamped to the base disc. If the fastener is vertically mounted, then clamping the swivel head can cause bending that reduces the precision of the Cold Saw.
| |
| | |
| =Feature: Adjustable and Removable Vise Jaws=
| |
| | |
| *'''Adjustable and Removable Vise Jaws''' (to accommodate variety of workpiece shapes and dimensions)
| |
| | |
| [[Image: ColdSawV1ViseJaws.png]]
| |
| | |
| =Feature: Fixed Blade Guard=
| |
| | |
| *'''Fixed Blade Guard''' (to protect against unintended blade contact during operation)
| |
| | |
| [[Image: ColdSawV1BladeGuard.png]]
| |
| | |
| =Feature: Forward and Backward Drive Stops=
| |
| | |
| *'''Forward and Backward Drive Stops''' (to prevent cutting into vise and to hold blade in mid-air while mounting the workpiece)
| |
| | |
| [[Image: ColdSawV1Stops.png]]
| |
| | |
| =Uniform Part Dimensions=
| |
| | |
| *'''Plate: 25.4mm x 304.8mm''' (Base Plate, Swivel Plate)
| |
| | |
| | |
| *'''Flat Bar: 76.2mm x 50.8mm''' (Shaft Block, Fixed Block, Moving Block)
| |
| | |
| *'''Flat Bar: 25.4mm x 127mm''' (Support Bar, Bridge Bar, Interface Bar, Vise Jaw)
| |
| | |
| *'''Flat Bar: 3.175mm x 25.4mm''' (Blade Guard Support)
| |
| | |
| *'''Flat Bar: 1.6mm x 152.4mm''' (Blade Guard)
| |
| | |
| | |
| *'''Round Bar: 152.4mm DIA''' (Base Disc)
| |
| | |
| *'''Round Bar: 127mm DIA''' (Blade Mount Disc)
| |
| | |
| *'''Round Bar: 76.2mm DIA''' (Shaft Collar with Axial Tensioning, Large Thrust Washer)
| |
| | |
| | |
| *'''Round Bar: 50.8mm DIA''' (Shaft Coupling, Shaft Collar)
| |
| | |
| *'''Round Bar: 31.8mm DIA''' (Shaft, Operation Handle, Vise Handle)
| |
| | |
| *'''Round Bar: 8mm DIA''' (Pin)
| |
| | |
| | |
| *'''Setscrew: M8x1.25 THREAD'''
| |
| | |
| *'''Bolts and Nuts: M12x1.75 THREAD'''
| |
| | |
| *'''Threaded Rod: M30x3.5 THREAD'''
| |
| | |
| *'''Nuts: M30x3.5 THREAD'''
| |
| | |
| =Uniform Mounting Dimensions=
| |
| | |
| *'''Swivel Mechanism'''
| |
| | |
| Base Disc Mounting Rectangle Sides: 60mm x 100mm'''
| |
| | |
| *'''Vise Mechanism'''
| |
| | |
| Vise Mounting Rectangle Sides: 50mm x 90mm
| |
| | |
| Center-to-Center Distance Between Vise Shaft and Threaded Rod: 95mm
| |
| | |
| *'''Rotary Support Mechanism'''
| |
| | |
| Shaft Block Mounting Rectangle Sides: 30mm x 55mm
| |
| | |
| *'''Drive Mechanism'''
| |
| | |
| Interface Mounting Rectangle Sides: 75mm x 80mm
| |
| | |
| Hydraulic Motor Mounting Rectangle Sides: 40mm x 100mm
| |
| | |
| *'''Blade Guard'''
| |
| | |
| Center-to-Center Distance between Blade Guard Support Screws: 100mm
| |