Torch Table Zaxis: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
(Created page with '=Bill of Materials= Bill of Materials 5172T12$2.50 per Pack {| border="1" !Item !Number !Cost !Further Info !Purpose !Aquired? |- |V-Groove Bearings 3/...')
 
No edit summary
Line 1: Line 1:
=Bill of Materials=
=Bill of Materials=
[[Torch_Table_BoM | Bill of Materials]]
Item Discription Amount Cost per item Further Info Purpose Aquired?
5172T12$2.50 per Pack
Bearing R6-2RS 3/8"x7/8"x9/32" Sealed 10 pack 0 $14.95 VXB Part Number: Kit711 For preventing the carrage from jumping the track no
{| border="1"
V-Groove Bearings 3/8 inch single pack 4 9.95 VXB V-Groove bearings Part number: Kit8407 To provide low friction linear motion no
!Item  
3/8 inch Hard Fiber Washers Pack of 100 8 2.5 McMaster Part Number: 95601A330 Holding bearings no
!Number
Hot rolled steel 3"x1/8" plate 10.0 Ft. 1.083333333 12.7 Metalsdepot To provide material for motor mounts no
!Cost  
Hot rolled steel 1"x1" square tubes 16 gauge 24ft for $23.28 16 23.28 Metalsdepot To provide structural support no
!Further Info  
Gear Rack  (1/2” sq. x 72” 20 DP 20 Deg) 6 feet per rack 1.333333333 24.8 Standard Steel Specialty Part Number: 200011 rack for gear to ride on no
!Purpose  
3 x 1/8 inch cold rolled Plate 6.0 Ft. 1.333333333 17.28 Metalsdepot To provide material to make rails no
!Aquired?
"3/8 inch threaded rod, Overall Length
|-
36"""  Each 22.8 $2 McMaster Part Number: 98837A031 for connecting the top and bottom carage no
|V-Groove Bearings 3/8 inch
3/8 inch nuts Pack of 100 16 4.2 Part Number: 90473A031 For locking threaded rod in place no
|4
3/8 inch washers Pack of 140 16 3.23 Part Number: 90126A031 For locking nuts and for spacers no
|$9.95 Each, Total $39.80
Steel 20 Deg Pressure Angle Spur Gear 20 Pitch, 20 Teeth, 1" Pitch Dia, 1/2" Bore Each 1 15.37 McMaster Part Number: 5172T12 Attaches to stepper motors and interfaces with gear rack no
|[http://www.vxb.com/page/bearings/CTGY/V-Groove-Bearings VXB V-Groove bearings]
sleeve bearing Each 1 1.34 McMaster Part Number: 6391K143 to connect between the stepper motor and the gear, will also add a bit of adjustable length no
|To provide low friction linear motion and to constrain motion in the y axis
10-32 set screw 7/16" per Pack of 100 1 5.44 Part Number: 92311A428 Set screw for attaching spur gear, sleeve bearing to stepper shaft no
|no
10 gauge bolts Pack of 50 6 7.78 McMaster Part Number: 92610A245 stepper no
|-
10 gauge nuts Pack of 100 6 1.54 McMaster Part Number: 90480A011 stepper no
|Hot rolled steel 3"x1/8" plate
Zinc-Pltd Stl Pan Head Phillips Machine Screw 1/4"-20 Thread, 1-1/2" Length Pack of 100 4 10.75 McMaster Part Number:  90272A546 Connects the mount plate arms to the carrage no
|1 feet
Zinc & Yellow Plated Grade 8 Steel Hex Nut 1/4"-20 Thread Size, 7/16" Width, 7/32" Height Packs of 100 16 3.06 McMaster Part Number: 94895A029 For locking the mount plate swing tightness no
|$10.00 for 4' $10.00 Total
1/4 inch Nylon Thrust Bearing Each 4 1.05 McMaster Part Number: 2797T1 allows the motor to swing freely no
|[http://www.metalsdepot.com/ Metalsdepot]
stepper spring pack of 6 1 10 McMaster Part Number: 3114T79 Prevents stepper motor shaft from crunching no
|To provide material for stepper motor mount plates, stepper swing arms, and cross beam support
|no
|-
|Hot rolled steel 1"x1" square tubes 16 gauge  
|2 feet
|
|[http://www.metalsdepot.com/ Metalsdepot]
|To provide structural support
|no
|-
|200011 (1/2” sq. x 72” 20 DP 20 Deg) rack
|2' length so 1 rack
|$24.80 
|[http://www.stdsteel.com/ Standard Steel Specialty]
|rack for gear to ride on
|yes
|-
|3 x 1/8 inch cold rolled Plate  
|2 feet
|
|[http://www.metalsdepot.com/ Metalsdepot]
|To provide material to make rails
|no
|-
|threaded 3/8 inch rod
|2 feet
|
|[http://www.mcmaster.com/ McMaster]
|For attaching V-Groove Bearings, Ball Bearings, and connecting the top/bottom carage
|no
|-
|3/8 inch nuts
|50
|
|Part Number: 90473A031
|For locking threaded rod in place
|no
|-
|3/8 inch washers
|40
|
|Part Number: 90126A031
|For locking nuts and for spacers
|no
|-
|Steel Plain Bore 14-1/2 Deg Spur Gear 20 Pitch, 20 Teeth, 1" Pitch Diameter, |3/8" Bore
|1
|$15.37 Each
|[http://www.mcmaster.com/ McMaster] 5172T12, 1327K113, Part Number: 5912K12, 6412K11
|Attaches to stepper motors and interfaces with gear rack
|no
|-
|Thrust Bearing
|4
|
|[http://www.mcmaster.com/ McMaster] Nylon Part Number:  2797T1
|allows the motor to swing freely
|no
|-
|sleeve bearing
|1
|$1.34 each
|[http://www.mcmaster.com/ McMaster] Part Number: 6391K143
|to connect between the stepper motor and the gear, will also add a bit of adjustable length
|no
|-
|10 gauge bolts
|30
| $7.78 per Pack of 50
|[http://www.mcmaster.com/ McMaster] Part Number: 92610A245
|stepper
|no
|-
|10 gauge nuts
|30
| $1.54 per Pack of 100
|[http://www.mcmaster.com/ McMaster] Part Number: 90480A011
|stepper
|no
|-
|Hard Fiber Washer
|8
|$2.50 per Pack
|[http://www.mcmaster.com/ McMaster] Part Number: 95601A330
|Holding bearings
|no
|-
|stepper saftey spring
|1
|$10.00 per Pack of 6
|[http://www.mcmaster.com/ McMaster] Part Number: 3114T79
|
|no
|}

Revision as of 16:16, 31 August 2009

Bill of Materials

Item Discription Amount Cost per item Further Info Purpose Aquired? Bearing R6-2RS 3/8"x7/8"x9/32" Sealed 10 pack 0 $14.95 VXB Part Number: Kit711 For preventing the carrage from jumping the track no V-Groove Bearings 3/8 inch single pack 4 9.95 VXB V-Groove bearings Part number: Kit8407 To provide low friction linear motion no 3/8 inch Hard Fiber Washers Pack of 100 8 2.5 McMaster Part Number: 95601A330 Holding bearings no Hot rolled steel 3"x1/8" plate 10.0 Ft. 1.083333333 12.7 Metalsdepot To provide material for motor mounts no Hot rolled steel 1"x1" square tubes 16 gauge 24ft for $23.28 16 23.28 Metalsdepot To provide structural support no Gear Rack (1/2” sq. x 72” 20 DP 20 Deg) 6 feet per rack 1.333333333 24.8 Standard Steel Specialty Part Number: 200011 rack for gear to ride on no 3 x 1/8 inch cold rolled Plate 6.0 Ft. 1.333333333 17.28 Metalsdepot To provide material to make rails no "3/8 inch threaded rod, Overall Length 36"""  Each 22.8 $2 McMaster Part Number: 98837A031 for connecting the top and bottom carage no 3/8 inch nuts Pack of 100 16 4.2 Part Number: 90473A031 For locking threaded rod in place no 3/8 inch washers Pack of 140 16 3.23 Part Number: 90126A031 For locking nuts and for spacers no Steel 20 Deg Pressure Angle Spur Gear 20 Pitch, 20 Teeth, 1" Pitch Dia, 1/2" Bore Each 1 15.37 McMaster Part Number: 5172T12 Attaches to stepper motors and interfaces with gear rack no sleeve bearing Each 1 1.34 McMaster Part Number: 6391K143 to connect between the stepper motor and the gear, will also add a bit of adjustable length no 10-32 set screw 7/16" per Pack of 100 1 5.44 Part Number: 92311A428 Set screw for attaching spur gear, sleeve bearing to stepper shaft no 10 gauge bolts Pack of 50 6 7.78 McMaster Part Number: 92610A245 stepper no 10 gauge nuts Pack of 100 6 1.54 McMaster Part Number: 90480A011 stepper no Zinc-Pltd Stl Pan Head Phillips Machine Screw 1/4"-20 Thread, 1-1/2" Length Pack of 100 4 10.75 McMaster Part Number:  90272A546 Connects the mount plate arms to the carrage no Zinc & Yellow Plated Grade 8 Steel Hex Nut 1/4"-20 Thread Size, 7/16" Width, 7/32" Height Packs of 100 16 3.06 McMaster Part Number: 94895A029 For locking the mount plate swing tightness no 1/4 inch Nylon Thrust Bearing Each 4 1.05 McMaster Part Number: 2797T1 allows the motor to swing freely no stepper spring pack of 6 1 10 McMaster Part Number: 3114T79 Prevents stepper motor shaft from crunching no

Retrieved from "https://wiki.opensourceecology.org/index.php?title=Torch_Table_Zaxis&oldid=10031"