LifeTrac II Part Sourcing

Video of Tractor and Frame assembly in William's second month Dedicated Project Visits report:

Cut List

Square tube:

• 4 × 7'8"×4"×4" tubes for base
• 3 × 5'×4"×4" under base tubes
• 2 × 52"×4"×4" vertical chassis centre tubes
• 2 × 55"×4"×4" vertical chassis tubes for front corners
• 2 × 59"×4"×4" vertical chassis tubes for rear corners (PC mounting area)
• 2 × 84"×4"×4" top chassis tubes
• 3 × 44"×4"×4" top chassis tubes

Rounds:

• 4 × 28"×1-7/8" axle shafts
• 4 × 54"1-7/8" loader shafts
• 2 × 100"×6"×2" front loader arm tubes
• 2 × 84"×6"×2" rear loader arm tubes
• 12 × 8" dom to mount loader shafts to loader arms.
• 1-7/8"bore bushing tubing to mount loader arm shafts to frame
• 1"bore tubing for 8 bushings to connect h/cylinders to loaders
• plate to mount bushings to loader arms

Plate:

• 12 × 10"×8"×0.5" steel plates to mount flange bearings and hydraulic motors to
• 2 × 12"×12"×1/2" plate to mount h/cylinders to base
• 4 × 32"diameter × 9" wheels
• 1/2"plate & 1-15/16"tubing to make wheel mounts

Other

• [16] thrust bearings - in the form of large washers with 1-7/8" hole.
• [8] double-split shaft collars, 1-7/8"

Bolts

Functionality list:

• [40] 3/4x5-1/2", with [40] washers for one side and [40] metal lock nuts for the other side. For wheel plates & cylinder plates.
• [42] 3/4"x9" bolts, [80] washers, and [40] metal lock nuts. This is for the assembly of the main frame.
• [16] 1/2"x2" bolts + [16] nylon lock nuts + [16] lock washers to suit. Motor attachment to motor interface plate. These could be 2" studs, as these are welded to the motor interface plate.
• [8] 3/4"x2" bolts for motor; [8] nuts to weld; [8] lock washers. Attachment of motor interface plate to frame.
• [32] 5/8"x2"bolts + [32] metal lock nuts, [32] lock washers to suit. Mounting of bearings to frame.
• [32] 9/16"x2" fine thread bolts, [32] washers, [32] nylon lock nuts. Attachment of wheel to wheel hub. Includes studs, nuts, and washers.
• [4] 3/4"x4.5" bolts; [8] nuts; [4] nylon lock nuts. Mounting of wheel bushings to wheel shafts.

TOTALS:

• [40] 3/4"x5.5" bolts
• [42] 3/4"x9" bolts
• [4] 3/4"x4.5" bolts
• [8] 3/4"x2" bolts
• [120] 3/4" washers
• [80] 3/4" metal lock nuts
• [16] 3/4" nuts
• [4] 3/4" nylon lock nuts
• [8] 3/4" lock washers

• [16] 1/2"x2" bolts
• [16] 1/2" nylon lock nuts
• [16] 1/2" lock washers

• [32] 5/8"x2" bolts
• [32] 5/8" metal lock nuts
• [32] 5/8" lock washers

• [32] 9/16"x2" bolts
• [32] 9/16" washers
• [32] 9/16" nylon lock nuts

Hydraulics

Note that the following list involves 2 loaders. For a simpler version, a single front loader is sufficient. Two loaders are used for extreme flexibility.

(download Blender file here)

Main

Parts from Surplus Center:

Functionality list:

Note: Green indicates finalized shopping list from Surplus Center. Blue indicates list from McMaster Carr. Red is Dalton Hydralics. See Parts Sourcing for contact information.

1. [8] flange Bearings - [1]
2. [2] Front Loader cylinders - 36" - $174 - 48 5/8" retracted length - [2]
3. [4] 3/8 NPTM x 1/2 NPTF 90 SWIVEL [3] for Front Loader Cylinders up to hose
   1. 4.9 square inch area at 2500 PSI implies 12000 lb of force for each cylinder
4. [0] Rear loader cylinders - [4]
5. [0] SAE 8M x 1/2 NPTF 90 SWIVEL [5] for Rear Loader Cylinders
6. [4] QA plate hydraulic cylinders & 2 Rear Loader [6]
7. [0] 3/8 NPTM x 1/2 NPTF 90 SWIVEL [7] for Q.A. Plate Cylinders
8. [4] Motors - [8]
   1. [8] SAE M 10 to NPT M 1/2" for Ports [9]
   2. [4] SAE 4M TO 1/4" NPTM CONNECTOR for Case Drains [10]
   3. [8] 1/2" QC for Motors [11]
   4. [4] 1/4" QC for motors [12]
9. [4] 1-1/4" shaft couplers - [13]
10. [1] 1-3/8" 6T fully splined shafting - [14]
11. [2] Female 1-3/8" 6T spline coupling - [15], $30 each
12. [12] 1.875" double split shaft collars - [16]
    1. got 10 double split
    2. got 2 single split - [17]

Valves

• [1] 3-spool motor valve, 25 gpm - [18], $288
• [4] 1/2" Quick Couplers [19] - for motor valve work ports
• [4] 1/2" NPT M to NPT M 90deg Elbow for Motor Valve working ports [20] - for 2 sets of work ports to wheel motors
• [4] 3/4" NPT quick couplers - Dalton Hydraulics - 2 for in/out, 2 for auxiliary work ports
• [2] 1/2 NPT hex nipples [21]-for auxiliary pair of motor valve work ports
• [2] 3/4 NPT hex nips [22] - in and out of valve
• [2] 3/4 NPT to 1/2 NPT bushing [23] - auxiliary work ports

OSE Danfoss Black 2 Spool

• [4] SAE 8M TO 1/2" NPTM CONNECTOR for working ports [24]
• [6] 1/2" NPT QUICK COUPLER F/F S20-4 [25]
• [1] SAE 10 PLUG for OSE BLACK 2 Spool [26]
• [2] SAE 10M TO 1/2" NPT CONNECTOR [27]

3 Spool Husco

• [1] 3/4" NPT quick couplers - Dalton Hydraulics - 1 pair for inlet
• [1] 3/4" NPT nip - [28] - for inlet
• [3] 1/2" nip for return cross [29]
• [1] 1/2"-1/4" bushing - to accept case drain return [30]
• [2] quick coupler pairs for return line - [31]
• Pipe cross fitting on the return line to accommodate case drain return - [32]
• [1] SAE 12 M to NPT 3/4 M Connector [33]
• [1] SAE 10M TO 1/2" NPT CONNECTOR [34]
• [1] 1/2 X 1/2 X 1/2 NPTF TEE [35]

2 Spool Prince Valve

• [1] 3/4" Quick Coupler for outlet (already included in central 3-spool motor valve)
• [2] 3/4" NPT nip for inlet/outlet - [36]
• [1] 3/4" NPT tee (already have these) for inlet
• [2] 3/4" to 1/2" bushings - [37]
• [1] 1/2" NPT male elbow - [38]
• [2] 1/2" quick coupler pairs - [39]

Cushion Valves

• [2] 1/2 NPT 30 GPM 1500-3000 PSI HYD CUSHION VALVES - [40]
• [4] 1/2" male QC tips to plug into valves, which already have female QCs [41]
• [2] 1/2 NPTM x 1/2 NPTF swivel [42] for cushion valve to mount tees, for separating to right and left cylinders; only one swivel needed per cushion valve
• [4] 1/2" nip - [43] - going from between swivel and tee.
• [4] NPTF Tee [44]- 4 for loaders only, not QA plates

Power Cube

• Note: pump is already obtained

• [1] Coupler half, 5/8" - $10
• [1] Coupler half, 1" - $10
• [1] Solid spider - $14
• [1] Breather cap - [45] - $8
  • [1] 3/4 NPT coupling - found at big box hardware stores
• [1] Suction strainer, 2" to 1-1/4" - [46] - $23
  • Use for dual Power Cubes
  • [1] Use 2" coupler from bix box store to thread into Power Cube frame
• [1] Pressure relief for power cube bypass- [47]
• [1] 20 GPM return Line Filter - [48]
• [1] 3/4" NPT Swivel for return line filter going into frame - [49]
• [2] 3/4" NPT hex nip on both sides of filter - [50]
• [1] 1"-3/4" NPT reducer bushing for frame receptacle for return filter - [51]
• [1] 3/4" quick coupler for return line to filter
• [2] 1/2" quick couplers for main power lines

Hoses:

• [1] 2 foot hose from pump outlet to return line filter - [52]
• [2] 10 foot hoses, already have these - [53]

Pressure Bypass:

• [1] 1/2" NPT Bypass valve - [54]
• [3] 1/2" Quick couplers - 1 complete for tee near pump, one going from return filter to tee, and male tip for return line. This gives one extra female quick coupler left over. This set of 3 QCs does not cover hoses going from and to the PowerCube.
• [4] 1/2" NPTF hex nip for one and other side of tee, on both tees - [55]
• [2] 1/2" NPTF tee - from outlet of pump to pressure bypass, and from bypass valve into return line filter - [56]
• [1] Fitting from return line to bypass valve

Hoses

Between Motor Valves & Motors

• [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of the valves [57]
• [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of front motors [58]
• [4] 1/2 X 1/2 X 1/2 NPTF TEE [59]
• [4] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for rear motors [60]

Motor Case Drains

• [2] 1/4" X 72" NPTM 2750 PSI HYD HOSE to run parallel with tractor sides [61]
• [1] 1/4" X 30" NPTM 2750 PSI HYD HOSE from Tee to Tee in return hose [62]
• [1] 1/4" X 36" NPTM 2750 PSI HYD HOSE to Rear Motors [63]
• [3] 1/4 X 1/4 X 1/4 NPTF TEE [64]
• [3] 1/4 NPT hex nipples [65]
• [4] 1/4" NPT quick couplers are already with the motors

Front Loader

• [2] 1/2" X 12" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE from Valves to Cushion [66]
• [2] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for left front loader cylinder [67]
• [1] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [68]
• [1] 1/2" X 60" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [69]

Front loader QA Cylinder Hoses

• [4] 3/8" NPTM x 1/2" NPTF swivel - [70] - swivels for QA cylinders
• [2] 1/2" nips - going from cylinder swivels to tees - [71]
• [2] 1/2" NPTF tees - from cylinder to hoses - [72]
• [2] male QC tips - for plugging into control valves - [73]
• [2] 1/2" X 48" NPTM 3000 PSI HYD HOSE [74]
• [1] 1/2" X 120" NPTM 3000 PSI HYD HOSE [75]
• [1] 1/2" X 144" NPTM 3000 PSI HYD HOSE [76]

Rear Loader Hoses

• [2] 1/2" X 12" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE to Cushion Valve [77]
• [1] 1/2" X 60" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE [78]
• [1] 1/2" X 96" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE [79]
• [1] 1/2" X 84" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE [80]
• [1] 1/2" X 120" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE [81]

Rear loader Q.A. Cylinder Hoses

• [4] 3/8" NPTM x 1/2" NPTF swivel - [82] - swivels for QA cylinders
• [2] 1/2" nips - going from cylinder swivels to tees - [83]
• [2] 1/2" NPTF tees - from cylinder to hoses - [84]
• [2] male QC tips - for plugging into control valves - [85]
• [2] 1/2" X 48" NPTM 3000 PSI HYD HOSE [86]
• [1] 1/2" X 120" NPTM 3000 PSI HYD HOSE [87]
• [1] 1/2" X 144" NPTM 3000 PSI HYD HOSE [88]

Seat

• [1] Tractor Seat [89]

Wheel bearings

Front loader cylinder

Front loader cylinder fittings

Rear loader cylinder

|

Rear loader cylinder fittings

Quick attach plate cylinder

Wheel motors

Wheel motor fittings

File:Lt2wheelmotorcdfittings.jpg

Wheel motor case drain fittings

Spline coupler, female part

Spline shaft, male

Wheel motor shaft coupler

Shaft collars, 3 per wheel

2 spool motor valve, 25 gpm

5 spool valve, 20 gpm

Cushion valve for front and rear loaders

1/2 inch NPT swivel

1/2 inch NPT nip

Half inch tee

Pressure relief valve for Power Cube

Spline shaft, male