CNC Circuit Mill/Manufacturing Instructions: Difference between revisions
| Line 15: | Line 15: | ||
=1 Process= | =1 Process= | ||
*Cut Angle | *Cut Angle 0.125" x 1.5" x 1.5" | ||
To 14 pieces of 360mm length | |||
To 11 pieces of 160mm length | |||
*Angle Template | *Angle Template | ||
Revision as of 22:47, 6 January 2012
1 Preparation
- Edit
https://docs.google.com/spreadsheet/ccc?key=0AlpsBarfpPkzdFk5aDY3dHM0eEhfZHNkWVppdV9EelE
1 Process
- Cut Angle 0.125" x 1.5" x 1.5"
To 14 pieces of 360mm length
To 11 pieces of 160mm length
- Angle Template
70mm long, 0.125" x 1.5" x 1.5" steel angle.
Use pilot bit. Differentiate the 2 holes as A and B after drilling. Which is which does not matter.
ANGLE HOLE A - Mark and drill hole A on one angle side, 13mm from the inner joining edge of angle, close to the end of the angle.
ANGLE HOLE B - Mark and drill hole B on the other angle side, 13 from the inner joining edge of angle, 26mm apart (distance is angle-parallel) from hole A.
- Tube Template
0.125" x 1.5" x 1.5" x 180mm steel tube.
All holes drilled with only pilot bit. Keep angle template usage consistent by keeping its 2 tube contact faces the same for all holes for a given surface. Ensure tube is on flat surface.
TEMPLATE REFERENCE HOLE Use angle template hole A to drill reference hole near end of tube.
TEMPLATE MOTOR HOLE Mark and drill 16mm tube-parallel from reference hole.
TEMPLATE STEPPER HOLES Mark 15.5mm tube-parallel from reference hole then drill 2 holes each 15.5mm tube-perpendicular from mark.
TEMPLATE SHAFT HOLE Mark 50mm tube-parallel from reference hole then drill 1 hole at mark using angle template hole A.
TEMPLATE FRAME HOLE Mark 170mm tube-parallel from reference hole then drill 1 hole at mark using angle template hole A.
TEMPLATE ANGLE HOLE Drill 1 hole using angle template hole B while hole A is set to the template shaft hole with rod.
- X Angles
0.125" x 1.5" x 1.5" x 360mm steel angle (4)
Ensure consistency of template usage.
XLONG REFERENCE HOLE Drill a reference hole at the center of all 4 angle pieces using the tube template.
XLONG STEPPER HOLES Drill the 2 stepper holes on 1 angle piece from its reference hole using the tube template. Flip the template to drill 2 more stepper holes from the 1 angle piece's reference hole.
XLONG SHAFT/FRAME HOLES Drill the shaft and frame holes on all 4 angle pieces from their respective reference holes using the tube template. Flip the template and do the same on the other side of the reference hole.
XLONG ANGLE HOLES Drill 2 angle holes on each of the 4 angle pieces using the tube template, 50mm hole held by rod to the xlong frame holes.
0.125" x 1.5" x 1.5" x 160mm steel angle (4)
Ensure template usage consistency.
XSHORT REFERENCE HOLE Drill a reference hole at the center of all 4 angle pieces using the tube template.
XSHORT SHAFT HOLES Drill the shaft holes on all 4 angle pieces from their respective reference holes using the tube template. Flip the template and do the same on the other side of the reference hole.
XSHORT ANGLE HOLES Drill 2 angle holes on each of the 4 angle pieces using the template angle holes, 50mm hole held by rod to the xshort shaft holes.
0.125"-XSPINDLE
- Y Angles
0.125" x 1.5" x 1.5" x 160mm steel angle (
- Z Angles
0.125" x 1.5" x 1.5" x
- Edit Processing Folder (copy/paste "Arduino1.0/lib/RXTcomm.jar" into Processing/lib)
- Edit GRBL Folder (edit "MakeFile" such that the serial port name "...tty.usb*" is replaced with the correct name corresponding to your computer OS)
- Upload Microcontroller Code
- Run gctrl code as a processing sketch. For any function of gctrl, press and hold down the key for the popup windows to populate.