View source for Jonathan Prusa i3 Build

=Module 1=
*[12] l brackets.
*[24] set screws
*[14] m4 Tnuts
*[8] m5 Tnuts
*[6] small washers - note that they should be larger as they fall through.
*[4] square blocks
*[2] rounded blocks
*[6] corner brackets
*[2] shortest smooth rods
*[2] longest smooth rods
*[1] 
#Larger washers
*[4] m4x14 bolts for rounded blocks
*[6] m4x8 panhead bolts for idler and power supply
#5:54 to put in the set to set screws. Definitely needs to use technique.
#Forgot to add the vertical l-brackets - was taken apart.
#58 minutes to the idler. Exactly 2x over optimum time.

=Module 2 - Extruder Carriage=
*[7] bearings
*[6] zip ties
*[3] 3D printed pieces
*[1] stepper motor
*[1] pulley
*[2] bearings
*[1] m3x16
*[3] m3x20
*[3] lock washers
#23:10 for time - :50 over world record

=Module 3 - Z Motors=
*[4] m4x8 panhead screws
*[4] m4 t nuts
*[2] steppers
*[2] plexiglas faces
*[2] couplers
*[2] motor brackets
*[8] m3x12 panhead screws
*[8] m3 lock washers
#9:20 - 30 seconds over the 8:50 olympic record.

=Module 4 - Heat Bed=
*[2] 16 gauge wires
*[1] thermistor
*[2] 7" red wire
*[2] 7" black wire
*[3] bearings
*[3] bearing holders
*[1] belt holder
*[6] m3x20 pan head screws
*[2] m3x12 pan head screws
*[4] springs
*[4] thumb screws
*[4] m3x16 pan head screws
*[8] m3 lock nuts
#14:10 for electronic solder + wiring.
#Ream out the plastic piece holes
#43:22, or 29:12 if parallel cf 27:30.

=Module 5 - Bed Motor=
*[1] large motor
*[1] pulley
*[1] bracket
*[2] m4x8 panhead srews
*[4] m3x8 panhead
*[4] lock washers
#5:45 cf 3:45. OT on looking for screws.

=Module 6 - End Stops=
*[3] stop holders
*[3] end stop electronics
*[5] 3mm lock nuts
*[2] 3x8 mm cap head screw
*[3] 3x20 mm cap head screw
#5 min of 3:30 world record

=Module 7 - Extruder assy=
#14:40 using soldering iron for heatshrink. Beat the world record of 16:20.

=Module 8 - Power Supply=
*19:39, beats the world record by one minute.

=Module 9 - Controller=
*[1] m4 t nut
*[1] m4x8 cap head
*[1] plexiglas mount
*[1] controller board
*[3] m3 lock washers
*[3] m3x25 cap head screws
#3: 4:00 cf 3:00

=Module 10 - Controller=
*[4] stepper wires
*[3] endstop wires 
#17:30 cf 12:40, with several minutes wasted on doing combined bundle instead of separate.

#About 3:30 total.

=Overall=
*Heated bed bearings + rods - put them in before tightening bearing holders.
*2:47, with 29 minutes on wiring.