CNC Circuit Mill/Manufacturing Instructions: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
(Redirected page to CNC Machine)
 
(62 intermediate revisions by 3 users not shown)
Line 1: Line 1:
=1 Preparation=
#redirect [[CNC Machine]]
 
*
<html><iframe width='800' height='300' frameborder='0' src='
 
https://docs.google.com/spreadsheet/pub?hl=en_US&hl=en_US&key=0AlpsBarfpPkzdFk5aDY3dHM0eEhfZHNkWVppdV9EelE&output=html
 
'></iframe>
</html><br/>
 
*Edit
 
https://docs.google.com/spreadsheet/ccc?key=0AlpsBarfpPkzdFk5aDY3dHM0eEhfZHNkWVppdV9EelE
 
=1 Process=
 
*Cut Angle
 
1 X Components
 
2 Long (4)
 
2 Short (9)
 
1 Y Components
 
2 Long (4)
 
1 Z Components
 
2 Long (6)
 
2 Short (2)
 
*Angle Template
 
70mm long, 0.125" x 1.5" x 1.5" steel angle.
 
Use pilot bit. Differentiate the 2 holes as A and B after drilling. Which is which does not matter.
 
ANGLE HOLE A - Mark and drill hole A on one angle side, 13mm from the inner joining edge of angle, close to the end of the angle.
 
ANGLE HOLE B - Mark and drill hole B on the other angle side, 13 from the inner joining edge of angle, 26mm apart (distance is angle-parallel) from hole A.
 
*Tube Template
 
0.125" x 1.5" x 1.5" x 180mm steel tube.
 
All holes drilled with only pilot bit. Keep angle template usage consistent by keeping its 2 tube contact faces the same for all holes for a given surface. Ensure tube is on flat surface.
 
TEMPLATE REFERENCE HOLE Use angle template hole A to drill reference hole near end of tube.
 
TEMPLATE MOTOR HOLE Mark and drill 16mm tube-parallel from reference hole.
 
TEMPLATE STEPPER HOLES Mark 15.5mm tube-parallel from reference hole then drill 2 holes each 15.5mm tube-perpendicular from mark.
 
TEMPLATE SHAFT HOLE Mark 50mm tube-parallel from reference hole then drill 1 hole at mark using angle template hole A.
 
TEMPLATE FRAME HOLE Mark 170mm tube-parallel from reference hole then drill 1 hole at mark using angle template hole A.
 
TEMPLATE ANGLE HOLE Drill 1 hole using angle template hole B while hole A is set to the template shaft hole with rod.
 
*X Angles
 
0.125" x 1.5" x 1.5" x 360mm steel angle (4)
 
Ensure consistency of template usage.
 
XLONG REFERENCE HOLE Drill a reference hole at the center of all 4 angle pieces using the tube template.
 
XLONG STEPPER HOLES Drill the 2 stepper holes on 1 angle piece from its reference hole using the tube template. Flip the template to drill 2 more stepper holes from the 1 angle piece's reference hole.
 
XLONG SHAFT/FRAME HOLES Drill the shaft and frame holes on all 4 angle pieces from their respective reference holes using the tube template. Flip the template and do the same on the other side of the reference hole.
 
XLONG ANGLE HOLES Drill 2 angle holes on each of the 4 angle pieces using the tube template, 50mm hole held by rod to the xlong frame holes.
 
0.125" x 1.5" x 1.5" x 160mm steel angle (4)
 
Ensure template usage consistency.
 
XSHORT REFERENCE HOLE Drill a reference hole at the center of all 4 angle pieces using the tube template.
 
XSHORT SHAFT HOLES Drill the shaft holes on all 4 angle pieces from their respective reference holes using the tube template. Flip the template and do the same on the other side of the reference hole.
 
XSHORT ANGLE HOLES Drill 2 angle holes on each of the 4 angle pieces using the template angle holes, 50mm hole held by rod to the xshort shaft holes.
 
0.125"-XSPINDLE
 
*Y Angles
 
0.125" x 1.5" x 1.5" x 160mm steel angle (
 
*Z Angles
 
0.125" x 1.5" x 1.5" x
 
*Edit Processing Folder (copy/paste "Arduino1.0/lib/RXTcomm.jar" into Processing/lib)
 
*Edit GRBL Folder (edit "MakeFile" such that the serial port name "...tty.usb*" is replaced with the correct name corresponding to your computer OS)
 
*Upload Microcontroller Code
 
http://opensourceecology.org/wiki/CNC_Circuit_Mill/Manufacturing_Instructions/Upload_Microcontroller_Code
 
*Run '''gctrl code''' as a '''processing''' sketch. For any function of gctrl, press and hold down the key for the popup windows to populate.

Latest revision as of 04:17, 26 June 2014

Redirect to:

Retrieved from "https://wiki.opensourceecology.org/index.php?title=CNC_Circuit_Mill/Manufacturing_Instructions&oldid=120890"