Fits, Limits, and Tolerances: Difference between revisions
Jump to navigation
Jump to search
(Minor Text Formatting Fix) |
(Added some more links under the "Internal Links" section) |
||
| (9 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
*By doing this ahead of time, you take the need for "fiddling" out of the assembly / iterative design process | *By doing this ahead of time, you take the need for "fiddling" out of the assembly / iterative design process | ||
*[[Press Fit]] is a common example | *[[Press Fit]] is a common example | ||
*A '''Fit''' is a relationship between two components, typically based on a Hole and a Shaft, such as a bolt or rivet holding components together, a rod in a bearing, or a piston in an engine | |||
*The '''Limits''' are the upper and lower extremes of what is within the desired tolerance | |||
*The '''Tolerance''' is the total permissible variation of size | |||
*The '''Nominal Size''' is what is used in the [[CAD]] (ie the perfect/impossible dimension that you get as close to as the tolerance dictates) | |||
=Internal Links= | =Internal Links= | ||
* | *[[Construction Tolerances]] | ||
=External Links= | =External Links= | ||
| Line 17: | Line 21: | ||
*[https://youtu.be/2429BVMrZ4A A Video by the YouTube Channel "tarkka" Titled "Fits and Tolerances: How to Design Stuff that Fits Together" ] (Only a six minute video, so quicker to see, the others are ~20 minutes) | *[https://youtu.be/2429BVMrZ4A A Video by the YouTube Channel "tarkka" Titled "Fits and Tolerances: How to Design Stuff that Fits Together" ] (Only a six minute video, so quicker to see, the others are ~20 minutes) | ||
*[https://youtu.be/wvVMs2BZdeU A Video by the YouTube Channel "Tabletop Machine Shop" Titled "Limits and Fits: The ISO System" ] (Goes over the '''PROPER''' metric sytem, unlike the others shown above ''which use all the fraction of a thousandths of an inch'' mess) | *[https://youtu.be/wvVMs2BZdeU A Video by the YouTube Channel "Tabletop Machine Shop" Titled "Limits and Fits: The ISO System" ] (Goes over the '''PROPER''' metric sytem, unlike the others shown above ''which use all the fraction of a thousandths of an inch'' mess) | ||
*[https://www.rapiddirect.com/blog/types-of-fits/ An Article by "Rapid Direct" Titled "Types of Fits: How to Choose the Right Fits in Engineering" ] (Has Nice Infographics, Probably will embed some) | |||
*[http://home.iitk.ac.in/~nsinha/Metrology.pdf A Slideshow by The Indian Institute of Technology, Kanpur Titled "Engineering Metrology - N. Sinha - Mechanical Engineering Department - IIT Kanpur" ] | |||
[[Category: Design]] [[Category: Fits, Limits, and Tolerances]] [[Category: Standards]] [[Category: Metrology]] | |||
Latest revision as of 03:39, 11 June 2022
Basics
- This page goes over Fits, Limits, and Tolerances, and the application of them in design
- Essentially nothing is perfect, and getting something closer to perfect is costly/time intensive (see degrees of flatness / Lapping and whatnot) so you define what is acceptable for the application (ie specific hole for a shaft, etc)
- By doing this ahead of time, you take the need for "fiddling" out of the assembly / iterative design process
- Press Fit is a common example
- A Fit is a relationship between two components, typically based on a Hole and a Shaft, such as a bolt or rivet holding components together, a rod in a bearing, or a piston in an engine
- The Limits are the upper and lower extremes of what is within the desired tolerance
- The Tolerance is the total permissible variation of size
- The Nominal Size is what is used in the CAD (ie the perfect/impossible dimension that you get as close to as the tolerance dictates)
Internal Links
External Links
- The Wikipedia Page on Limits and Fits
- The Wikipedia Page on Engineering Fits
- The Wikipedia Page on Engineered Tolerances
- Limits, Fits, and Tolerance Calculator (ISO System)
- A PDF by the Department of Mechanical & Aerospace Engineering at the University of Florida titled "Typical Tolerances of Manufacturing Processes"
- A Video by the YouTube Channel "Blondihacks" Titled "Fits and Tolerances, Oh My!" (Given they are a hobby machinist they give some good perspective on how various levels can be achieved in a small shop realistically, and also present it in a straightforward manner)
- A Video by the YouTube Channel "tarkka" Titled "Fits and Tolerances: How to Design Stuff that Fits Together" (Only a six minute video, so quicker to see, the others are ~20 minutes)
- A Video by the YouTube Channel "Tabletop Machine Shop" Titled "Limits and Fits: The ISO System" (Goes over the PROPER metric sytem, unlike the others shown above which use all the fraction of a thousandths of an inch mess)
- An Article by "Rapid Direct" Titled "Types of Fits: How to Choose the Right Fits in Engineering" (Has Nice Infographics, Probably will embed some)
- A Slideshow by The Indian Institute of Technology, Kanpur Titled "Engineering Metrology - N. Sinha - Mechanical Engineering Department - IIT Kanpur"