Garage Door Opener Install: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
No edit summary
 
(12 intermediate revisions by the same user not shown)
Line 2: Line 2:


Programming: [https://docs.google.com/presentation/d/1IglMwlvzJzA5S6ePZJcBh-0rtOnXw41Hl-RiOQfvbNk/edit?slide=id.g33327038b48_0_0#slide=id.g33327038b48_0_0]
Programming: [https://docs.google.com/presentation/d/1IglMwlvzJzA5S6ePZJcBh-0rtOnXw41Hl-RiOQfvbNk/edit?slide=id.g33327038b48_0_0#slide=id.g33327038b48_0_0]
= Genie 7055 Garage Door Opener LED Status Codes =
Source - [https://chatgpt.com/share/69ab74fd-77e0-8010-9f81-7bc3ddb8b8dd]
=Service=
*Menards - https://www.menards.com/main/doors-windows-millwork/garage-doors-openers/garage-door-openers/genie-reg-1-hpc-belt-drive-garage-door-opener-with-bbu/7055-tpv/p-9115189600779039-c-12367.htm
*SKU - 4251794
*1.800.354.3643
*SN 243 532 120 156 AH
*Board - https://store.geniecompany.com/products/circuit-board-41922r-s
*[[File:geniereceipt.pdf]]
* Genie Support <Genie_Support@custhelp.com> - reply-to: Genie Support <overheaddoor@mailph.custhelp.com>date: Mar 7, 2026, 1:25 PM subject: No power / No movement [Incident: 260307-000339]
*Fried Board - see album [https://photos.app.goo.gl/tBThyUKJFn1epPEC8]. Component warrany is 5 years.
=Photos=
*https://photos.app.goo.gl/tBThyUKJFn1epPEC8
= Genie 7055 Garage Door Opener LED Status Codes =
{| class="wikitable"
! System State
! Opener Round LED (Blue)
! Opener Long LED (Purple)
! Sensor LEDs (Red / Green)
! Meaning
! Typical Action
|-
| Normal operation (fully programmed, ready)
| Solid Blue
| Off
| Red solid / Green solid
| System powered and operating normally
| None required
|-
| Programming mode entered
| Flashing Blue
| Off
| Red solid / Green solid
| User pressed SET/PROGRAM to begin programming
| Continue programming steps
|-
| Ready to program remote
| Flashing Blue
| Flashing Purple
| Red solid / Green solid
| Opener waiting for remote signal
| Press remote button to pair
|-
| Travel limit programming mode
| Blue on
| Purple flashing
| Red solid / Green solid
| System waiting for UP/DOWN limits to be set
| Set open and close positions
|-
| Door opening or closing normally
| Blue solid
| Off
| Red solid / Green solid
| Normal door movement
| None
|-
| Safe-T-Beam blocked
| Blue solid
| Off
| Red solid / Green flashing
| Beam interrupted or object in doorway
| Remove obstruction
|-
| Safe-T-Beam misaligned
| Blue solid
| Off
| Red flashing / Green off or flashing
| Sensors not aligned
| Realign sensors
|-
| Safe-T-Beam wiring fault
| Blue solid
| Off
| Red off / Green off
| Sensor wiring disconnected or damaged
| Inspect wiring to sensors
|-
| Door will not close unless wall button held
| Blue solid
| Off
| Red flashing or Green flashing
| Safety beam not detected
| Fix sensor alignment or wiring
|-
| Battery backup idle (AC power lost)
| Off
| Off
| Red solid / Green solid
| Opener powered only by battery and conserving energy
| Restore AC power to opener
|-
| Battery backup operating
| Blue dim or brief flash
| Off
| Red solid / Green solid
| Door operating on battery backup
| Restore AC power
|-
| System memory reset or limits not programmed
| Blue flashing
| Purple flashing
| Red solid / Green solid
| Travel limits missing
| Perform travel limit setup
|-
| Obstruction detected during travel
| Blue solid
| Off
| Red solid / Green solid
| Door encountered resistance
| Check tracks, rollers, springs, obstruction
|}

Latest revision as of 19:50, 7 March 2026

https://docs.google.com/presentation/d/1IglMwlvzJzA5S6ePZJcBh-0rtOnXw41Hl-RiOQfvbNk/edit#slide=id.g32e02103eca_0_0

Programming: [1]


Genie 7055 Garage Door Opener LED Status Codes

Source - [2]

Service

Photos

Genie 7055 Garage Door Opener LED Status Codes

System State Opener Round LED (Blue) Opener Long LED (Purple) Sensor LEDs (Red / Green) Meaning Typical Action
Normal operation (fully programmed, ready) Solid Blue Off Red solid / Green solid System powered and operating normally None required
Programming mode entered Flashing Blue Off Red solid / Green solid User pressed SET/PROGRAM to begin programming Continue programming steps
Ready to program remote Flashing Blue Flashing Purple Red solid / Green solid Opener waiting for remote signal Press remote button to pair
Travel limit programming mode Blue on Purple flashing Red solid / Green solid System waiting for UP/DOWN limits to be set Set open and close positions
Door opening or closing normally Blue solid Off Red solid / Green solid Normal door movement None
Safe-T-Beam blocked Blue solid Off Red solid / Green flashing Beam interrupted or object in doorway Remove obstruction
Safe-T-Beam misaligned Blue solid Off Red flashing / Green off or flashing Sensors not aligned Realign sensors
Safe-T-Beam wiring fault Blue solid Off Red off / Green off Sensor wiring disconnected or damaged Inspect wiring to sensors
Door will not close unless wall button held Blue solid Off Red flashing or Green flashing Safety beam not detected Fix sensor alignment or wiring
Battery backup idle (AC power lost) Off Off Red solid / Green solid Opener powered only by battery and conserving energy Restore AC power to opener
Battery backup operating Blue dim or brief flash Off Red solid / Green solid Door operating on battery backup Restore AC power
System memory reset or limits not programmed Blue flashing Purple flashing Red solid / Green solid Travel limits missing Perform travel limit setup
Obstruction detected during travel Blue solid Off Red solid / Green solid Door encountered resistance Check tracks, rollers, springs, obstruction
Retrieved from "https://wiki.opensourceecology.org/index.php?title=Garage_Door_Opener_Install&oldid=320910"