Open Source Induction Furnace Project: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
(→‎Notes: Added notes from Benny)
(Redirected page to Induction Furnace)
 
(37 intermediate revisions by 10 users not shown)
Line 1: Line 1:
==Introduction==
#redirect [[Induction Furnace]]
 
This project involves the design of:
* a high frequency, high-power induction furnace circuit (between 20 and 50 kW), and
* the melting chamber proper.
 
Well, we could buy a turnkey system perhaps for $5k total used, and run it from the LifeTrac generator. The only disadvantage to this route is that if it breaks we’re dead-in-the-water – either with the impossibility of fixing closed-source technology, or a high repair bill. A single component which blows and is inaccessible for fixing could in principle turn a working power supply into worthless junk. Thus, it is worthwhile to tame this technology by open-sourcing the design.
 
==Goals==
The furnace should have the following characteristics:
 
#Induction furnace or any other technology that can do this within a budget of 20 kW of electric input, with minimal pollution
#Suitable for melting all metals and alloying
#300 lb per hour steel melting furnace for casting
#240 v ac, 20 kW power source available
 
 
==Details==
The complete design should include all of the following:
 
===Induction Furnace Circuit===
# Scalable from 20 up to 50 kW in units of 1 or 5 kW
# Allows for power and frequency selection
# Power source may be either 1 or 3 phase electrical power
 
===Heat Dissipation System===
Specifications of a cooling or heat dissipation system.
 
===Coil===
# Modular, adaptable design specifications for primary coil windings
 
===Melt Chamber===
# Geometical design of melt chamber and basic power transfer calculations
# Should include provisions for loading and pouring.
 
===Other Considerations===
# Complete bill of materials
# Fabrication files for circuit and other components
# Sourcing information for components
# System design and process flow drawings
 
==Notes==
===Benny===
I just read that you plan to build up an induction furnace. That´s a an interesting and exciting plan.While reading the aricle some remarks came to my mind.
 
But before I want to introduce myself:
 
I am Benny from Germany, Hannover.
I am diploma engineer for electrotechnology and working at the university. I am dealing with some induction heating/ melting applications like induction melting of glasses (that is possible!) and induction furnaces for cast iron.
 
Some remarks from my point of view:
 
# It is possible to build up a low cost furnace with the mentioned parameters.
# The frequency of 9,6 kHz is much to high. The efficiancy will be so bad, that it will be hardly possible to melt steel or iron. Due to the small penetration depth of about 2 mm with this frequency and this electrical resistance. So it needs a really small diameter of the crucible, and thats not helpful. Also the refractory material will be strained too much, so that a small lifetime is given. This will raise the cost for the operating.
# 50 Hz or 60 Hz is a better solution. And you can save the cost for the hf-converter.
# How much material do you want to cast at one time? The maximum, what i expect to be possible with 50 kW will be about 50 to 60 kg.
# What kind of raw material should be charged? It is important for the starting, because the initial density should not be too small (packing density). And the other question is, what kind of scrab it will be.
There are so many problems known with content of zinc (hot zinc dipped) and other materials. The lifetime of common refractory material is really small. And what is more important the security for the personal is not given without a strong exhaust system, due to the toxic steam. I expect this as a strong cost factor.
 
===Power Supply===
*50 kW for $1600 - [http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=200415768835&rvr_id=&crlp=1_263602_263622&UA=L*F%3F&GUID=1357ab741250a0265337bec7ff94d6a7&itemid=200415768835&ff4=263602_263622]
*20 kw STC 3 phase 120 - 480V, also 1 phase - generator - $692 -[http://cgi.ebay.com/20kw-STC-3-Phase-277-480-12-Wire-generator-Head-altern_W0QQitemZ160369799644QQcmdZViewItemQQptZBI_Generators?hash=item2556c8f1dc]
*50 kw STC 3 phase- $1300 - [http://cgi.ebay.com/50KW-STC-3-Phase-12-Wire-generator-alternator_W0QQitemZ160357088416QQcmdZViewItemQQptZBI_Generators?hash=item255606fca0]
**LifeTrac 55 hp can produce 38 kW with this head
 
===Melt Calculations===
[[Image:inductioncalc.jpg]]
 
==See Also==
* Original blog post: http://openfarmtech.org/weblog/?p=1373
* Furnace selection: http://www.articlesfactory.com/articles/hobbies/induction-furnace-and-cupola-furnace-information.html
* UFES: http://www.ufes.com/index.php?n=Foundry.FurnacesOvens
===DIY Furnaces===
*http://www.richieburnett.co.uk/indheat.html
*http://www.hvguy.4hv.org/ih/
*http://webpages.charter.net/dawill/tmoranwms/Elec_IndHeat1.html
* 1 kW Induction Furnace Kit: http://webpages.charter.net/dawill/tmoranwms/Elec_IndHeat8.html
*http://www.dansworkshop.com/electricity-and-electronics/induction-heating.htm
===Commercial===
*Commercial induction furnace power supplies from Superior Induction - [http://www.superiorinduction.com/?gclid=CO2fgNqPtZkCFRAhDQodqjeo5Q]
*EPRI works with induction - The EPRI Center for Materials Production at Carnegie Mellon, Pittsburgh, PA, 412-268-3243
 
 
If you think there are missing or incorrect details here, please help correct that.
 
 
[[Category:Induction Furnace]]
[[Category:Specifications]]
[[Category:Metalworks]]
[[Category:Fabrication]]

Latest revision as of 21:25, 11 September 2011

Redirect to:

Retrieved from "https://wiki.opensourceecology.org/index.php?title=Open_Source_Induction_Furnace_Project&oldid=40696"