Cold Saw/V1 Design Files: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
 
(58 intermediate revisions by the same user not shown)
Line 1: Line 1:
=Assemblies=
=Uniform Mounting Dimensions=
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Base_Assembly Base Assembly]
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Vise_Assembly Vise Assembly]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Drive_Assembly Drive Assembly]
*'''Base Plate to Base Flat: 80mm x 520mm'''


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Support_Assembly Support Assembly]
*'''Base Flat to Vise: 50mm x 90mm'''


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Full_Assembly Full Assembly]
*'''Vise Rod to Rod: 95mm'''


=Uniform Shaft Accessories=
*'''Support Flat to Interface Flat: 75mm x 80mm'''


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Support_Thrust_Washer Thrust Washer]
*'''Hydraulic Motor to Interface Flat: 40mm x 100mm'''


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Drive_Collar Large Shaft Collar]
*'''Blade Guard to Interface Flat: 80mm x 100mm'''
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Pin_Collar Small Shaft Collar]


=Uniform Fasteners=
=Uniform Fasteners=


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Blade_Guard_Nut Nut]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Blade_Guard_Bolt Short Bolt]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Blade_Guard_Bolt Short Bolt]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Long_Screw Long Screw]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Interface_Bolt Long Bolt]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Long2_Screw Long2 Screw]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Coupling_Setscrew Short Setscrew]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Coupling_Setscrew Short Setscrew]
Line 31: Line 25:
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Collar_Setscrew Long Setscrew]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Collar_Setscrew Long Setscrew]


=Base System=
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Threaded_Rod Threaded Rod]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Baseplate Baseplate]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Short_Threaded_Rod Short Threaded Rod]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Base_Disc Base Disc]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Blade_Guard_Nut Small Nut]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Support_Plate Support Plate]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Large_Nut Large Nut]


=Clamp System=
=Uniform Spacers=


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Fixed_Block Fixed Block]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Short_Spacer Short Spacer]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Moving_Block Moving Block]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Long_Spacer Long Spacer]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Clamp_Jaw Clamp Jaw]
=Uniform Shafts=


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Shaft Clamp Shaft]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Handle Vise Handle]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Threaded_Rod Threaded Rod]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Operation_Handle Operation Handle]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Handle Clamp Handle]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Pin Pin]


=Support System=
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Coupling_Pin Coupling Pin]
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Shaft_Block Shaft Block]
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Support_Bar Support Bar]
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Bridge_Bar Bridge Bar]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Support_Shaft Support Shaft]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Support_Shaft Support Shaft]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Spindle Drive Shaft]


=Uniform Shaft Accessories=


=Drive System=
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Support_Thrust_Washer Thrust Washer]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Large_Thrust_Washer Large Thrust Washer]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Hydraulic_Motor Hydraulic Motor]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Drive_Collar Large Shaft Collar]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Interface_Plate Interface Plate]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Medium_Shaft_Collar Medium Shaft Collar]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Pin_Collar Small Shaft Collar]


=Assemblies=


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Shaft_Coupling Shaft Coupling]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Base_Assembly Base Assembly]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Coupling_Pin Coupling Pin]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Vise_Assembly Vise Assembly]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Spindle Drive Shaft]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Swivel_Assembly Swivel Assembly]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Support_Assembly Support Assembly]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Drive_Assembly Drive Assembly]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Mount_Disc Mount Disc]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Blade_Guard_Assembly Blade Guard Assembly]


[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Pin Pin]
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Full_Assembly Full Assembly]
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Blade Blade]
 
 
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Blade_Guard_Support Blade Guard Support]
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Blade_Guard Blade Guard]
 
 
 
[http://opensourceecology.org/wiki/Cold_Saw/V1_Design_Files/Operation_Handle Operation Handle]

Latest revision as of 18:53, 20 June 2012

Uniform Mounting Dimensions

  • Base Plate to Base Flat: 80mm x 520mm
  • Base Flat to Vise: 50mm x 90mm
  • Vise Rod to Rod: 95mm
  • Support Flat to Interface Flat: 75mm x 80mm
  • Hydraulic Motor to Interface Flat: 40mm x 100mm
  • Blade Guard to Interface Flat: 80mm x 100mm

Uniform Fasteners

Short Bolt

Long Screw

Long2 Screw

Short Setscrew

Long Setscrew

Threaded Rod

Short Threaded Rod

Small Nut

Large Nut

Uniform Spacers

Short Spacer

Long Spacer

Uniform Shafts

Vise Handle

Operation Handle

Pin

Coupling Pin

Support Shaft

Drive Shaft

Uniform Shaft Accessories

Thrust Washer

Large Thrust Washer

Large Shaft Collar

Medium Shaft Collar

Small Shaft Collar

Assemblies

Base Assembly

Vise Assembly

Swivel Assembly

Support Assembly

Drive Assembly

Blade Guard Assembly

Full Assembly

Retrieved from "https://wiki.opensourceecology.org/index.php?title=Cold_Saw/V1_Design_Files&oldid=66418"