Boxed Way: Difference between revisions
| Line 26: | Line 26: | ||
Stepper Motor - NEMA 23 from [http://www.linengineering.com/LinE/contents/stepmotors/5818.aspx Lin Engineering] - 5818L-04S | Stepper Motor - NEMA 23 from [http://www.linengineering.com/LinE/contents/stepmotors/5818.aspx Lin Engineering] - 5818L-04S | ||
---- | |||
Leadscrew - Rolled or Ground Acme Screw OR Ballscrew, Stainless Steel, Machined Straight Ends - | Leadscrew - Rolled or Ground Acme Screw OR Ballscrew, Stainless Steel, Machined Straight Ends - | ||
| Line 32: | Line 34: | ||
Leadscrew Nut Mount - | Leadscrew Nut Mount - | ||
---- | |||
Thrust Bearing x2 - | Thrust Bearing x2 - | ||
Thrust Bearing Mount x2 - | Thrust Bearing Mount x2 - | ||
---- | |||
Shaft Coupling - Helical Beam, Clamp, Aluminum from [http://www.mcmaster.com/#standard-shaft-couplings/=jshb9m Mcmaster-Carr] - 6208K541 (~40 / unit) ? | Shaft Coupling - Helical Beam, Clamp, Aluminum from [http://www.mcmaster.com/#standard-shaft-couplings/=jshb9m Mcmaster-Carr] - 6208K541 (~40 / unit) ? | ||
---- | |||
Screw x4 (for mounting stepper motor) - Stainless Steel 18-8, Socket Head Cap, M5x0.8 | Screw x4 (for mounting stepper motor) - Stainless Steel 18-8, Socket Head Cap, M5x0.8 | ||
| Line 46: | Line 54: | ||
Nut xX (for holding gib screw) - Stainless Steel 18-8, M5x0.8 | Nut xX (for holding gib screw) - Stainless Steel 18-8, M5x0.8 | ||
---- | |||
Lubrication Fitting | Lubrication Fitting | ||
---- | |||
Cast iron 2" x 6" x 12" | |||
=Build= | =Build= | ||
Cold Rolled Iron 2" x 4" (50.8mm x 101.6mm): XXX Length | Cold Rolled Iron 2" x 4" (50.8mm x 101.6mm): XXX Length | ||
Revision as of 06:01, 13 November 2012
Introduction
A boxed way is a type of linear slide. A linear slide is made of two things that can move freely in a line but not in any other way (ex. cannot bend or rotate or move along any other line).
The adhesive used between the ways and the base is #459-0087 - DP-190 Gray Scotch Weld. An adhesive is also used to bond the low friction bearing material to the saddle and that is #SBNS1763FC5OZ - Waylock 2-part adhesive.
Design
Tools
Reduced Shank Endmill
Materials
Stepper Motor - NEMA 23 from Lin Engineering - 5818L-04S
Leadscrew - Rolled or Ground Acme Screw OR Ballscrew, Stainless Steel, Machined Straight Ends -
Leadscrew Nut - Anti-Backlash, Axial mounting -
Leadscrew Nut Mount -
Thrust Bearing x2 -
Thrust Bearing Mount x2 -
Shaft Coupling - Helical Beam, Clamp, Aluminum from Mcmaster-Carr - 6208K541 (~40 / unit) ?
Screw x4 (for mounting stepper motor) - Stainless Steel 18-8, Socket Head Cap, M5x0.8
Screw xX (for mounting retainers) - Stainless Steel 18-8, Socket Head Cap, M5x0.8
Screw xX (for compressing gib) - Stainless Steel 18-8, Socket Head Cap, M5x0.8
Nut xX (for holding gib screw) - Stainless Steel 18-8, M5x0.8
Lubrication Fitting
Cast iron 2" x 6" x 12"
Build
Cold Rolled Iron 2" x 4" (50.8mm x 101.6mm): XXX Length