Boxed Way: Difference between revisions
No edit summary |
|||
| (36 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Introduction= | =Introduction= | ||
[[File: boxedwaydiagram.png| | A boxed way is a type of linear slide. A linear slide is made of two things that can move freely in a line but not in any other way (ex. cannot bend or rotate or move along any other line). | ||
[[File: boxedways.png| | |||
---- | |||
The adhesive used between the ways and the base is #459-0087 - DP-190 Gray Scotch Weld. An adhesive is also used to bond the low friction bearing material to the saddle and that is #SBNS1763FC5OZ - Waylock 2-part adhesive. | |||
[[File: boxedwaydiagram.png|200px]] | |||
[[File: boxedways.png|200px]] | |||
---- | ---- | ||
[[File: shaftcouplingbox.png|200px]] | [[File: shaftcouplingbox.png|200px]] | ||
[[File: xyboxed.png| | [[File: xyboxed.png|200px]] | ||
=Design= | =Design= | ||
| Line 13: | Line 19: | ||
[[File: cnclinear.svg|500px]] | [[File: cnclinear.svg|500px]] | ||
=Tools= | |||
Reduced Shank Endmill | |||
=Materials= | =Materials= | ||
Stepper Motor | Stepper Motor - NEMA 23 from [http://www.linengineering.com/LinE/contents/stepmotors/5818.aspx Lin Engineering] - 5818L-04S | ||
---- | |||
Leadscrew - Rolled or Ground Acme Screw OR Ballscrew, Stainless Steel, Machined Straight Ends - | |||
Leadscrew Nut - Anti-Backlash, Axial mounting - | |||
Leadscrew Nut Mount - | |||
---- | |||
Thrust Bearing x2 - | |||
Thrust Bearing Mount x2 - | |||
---- | |||
Shaft Coupling - Helical Beam, Clamp, Aluminum from [http://www.mcmaster.com/#standard-shaft-couplings/=jshb9m Mcmaster-Carr] - 6208K541 (~40 / unit) ? | |||
---- | |||
All fasteners are stainless steel 18-8, M3x0.5 | |||
Screw x4 (for mounting stepper motor) | |||
Screw xX (for mounting retainers) | |||
Screw xX (for compressing gib) | |||
Nut xX (for holding gib screw) | |||
---- | |||
Lubrication Fitting | |||
---- | |||
Cast grey iron 2" x 4" x 12" for Base (from SpeedyMetals) | |||
Cast grey iron 2" x 4" x 4" for Saddle (from SpeedyMetals) | |||
=Build= | =Build= | ||
Latest revision as of 07:02, 27 November 2012
Introduction
A boxed way is a type of linear slide. A linear slide is made of two things that can move freely in a line but not in any other way (ex. cannot bend or rotate or move along any other line).
The adhesive used between the ways and the base is #459-0087 - DP-190 Gray Scotch Weld. An adhesive is also used to bond the low friction bearing material to the saddle and that is #SBNS1763FC5OZ - Waylock 2-part adhesive.
Design
Tools
Reduced Shank Endmill
Materials
Stepper Motor - NEMA 23 from Lin Engineering - 5818L-04S
Leadscrew - Rolled or Ground Acme Screw OR Ballscrew, Stainless Steel, Machined Straight Ends -
Leadscrew Nut - Anti-Backlash, Axial mounting -
Leadscrew Nut Mount -
Thrust Bearing x2 -
Thrust Bearing Mount x2 -
Shaft Coupling - Helical Beam, Clamp, Aluminum from Mcmaster-Carr - 6208K541 (~40 / unit) ?
All fasteners are stainless steel 18-8, M3x0.5
Screw x4 (for mounting stepper motor)
Screw xX (for mounting retainers)
Screw xX (for compressing gib)
Nut xX (for holding gib screw)
Lubrication Fitting
Cast grey iron 2" x 4" x 12" for Base (from SpeedyMetals)
Cast grey iron 2" x 4" x 4" for Saddle (from SpeedyMetals)