Open Source Induction Furnace Project: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
No edit summary
(Redirected page to Induction Furnace)
 
(19 intermediate revisions by 9 users not shown)
Line 1: Line 1:
* [http://openfarmtech.org/weblog/category/global-village-construction-set/induction-furnace/ Induction Furnace posts]
#redirect [[Induction Furnace]]
* [http://openfarmtech.org/weblog/forum/induction-furnace/ Induction Furnace Forum]
* [[:Category: Induction Furnace]]
 
Project management site: http://openpario.mime.oregonstate.edu/projects/osif
 
[[Image:induction_furnace.jpg|right|alt=Induction Furnace.]]
==Introduction==
 
The Open Source Induction Furnace Project seems to be the most promising way to implement the [[foundry]].
This project involves the design of:
* a high-power induction furnace circuit (between 20 and 50 kW), and
* the melting chamber proper.
 
Well, we could buy a turnkey system perhaps for $5k total used, and run it from the LifeTrac generator. The only disadvantage to this route is that if it breaks we’re dead-in-the-water – either with the impossibility of fixing closed-source technology, or a high repair bill. A single component which blows and is inaccessible for fixing could in principle turn a working power supply into worthless junk. Thus, it is worthwhile to tame this technology by open-sourcing the design.
 
==Goals==
 
To fulfill our [[foundry]] goals,
The furnace should have the following characteristics:
 
#Induction furnace or any other technology that can do this within a budget of 20 kW of electric input, with minimal pollution
#Suitable for melting all metals and alloying
#300 lb per hour steel melting furnace for casting
#240 v ac, 20 kW power source available
 
==Conceptual Diagram==
 
This is a conceptual diagram of the entire Induction Furnace system from the [[Global Village Construction Set]]. The furnace is powered by 20 kW of 240VAC electricity from the [[LifeTrac]] generator. The entire system includes the power electronics, induction coil, and heating vessel - into which metal for melting is inserted. This diagram intends to document the relationship of functional components in the induction furnace system, as a basis for technical development of components and their integration.
 
The electronics part should be adaptable to different metals and different metal melting coil  geometries. Melting coils should also be modular, such that the power electronics can feed different coils. Basic functions include selection of heating frequencies, which are required for melting different metals or metal geometries. There should be a feedback in the electronics, where the amount of power given to the coil should match the quantity/geometry of metal being melted.
 
[[Image:induction_concept.jpg]]
 
 
==Details==
The complete design should include all of the following:
 
===Induction Furnace Circuit===
# Scalable from 20 up to 50 kW in units of 1 or 5 kW
# Allows for power and frequency selection
# Power source may be either 1 or 3 phase electrical power
 
===Heat Dissipation System===
Specifications of a cooling or heat dissipation system.
 
===Coil===
# Modular, adaptable design specifications for primary coil windings
 
===Melt Chamber===
# Geometical design of melt chamber and basic power transfer calculations
# Should include provisions for loading and pouring
# Given our goals, which is best: a coreless or a channel induction furnace type [http://www.wisegeek.com/what-is-an-induction-furnace.htm] ?
## channel: useful in the melting of lower melt temperature metals; less turbulence at the surface.
## coreless: stronger stirring
# Pouring: manual pouring methods are more suited to low volume production lines.
====Crucible====
* See: Crucibles for Induction Melting - Guidelines for Selection and Use: http://www.engineeredceramics.com/crucible.htm
 
===Other Considerations===
# Complete bill of materials
# Fabrication files for circuit and other components
# Sourcing information for components
# System design and process flow drawings
 
==Notes==
===Benny===
I just read that you plan to build up an induction furnace. That´s a an interesting and exciting plan.While reading the aricle some remarks came to my mind.
 
But before I want to introduce myself:
 
I am Benny from Germany, Hannover.
I am diploma engineer for electrotechnology and working at the university. I am dealing with some induction heating/ melting applications like induction melting of glasses (that is possible!) and induction furnaces for cast iron.
 
Some remarks from my point of view:
 
# It is possible to build up a low cost furnace with the mentioned parameters.
# The frequency of 9,6 kHz is much to high. The efficiancy will be so bad, that it will be hardly possible to melt steel or iron. Due to the small penetration depth of about 2 mm with this frequency and this electrical resistance. So it needs a really small diameter of the crucible, and thats not helpful. Also the refractory material will be strained too much, so that a small lifetime is given. This will raise the cost for the operating.
# 50 Hz or 60 Hz is a better solution. And you can save the cost for the hf-converter.
# How much material do you want to cast at one time? The maximum, what i expect to be possible with 50 kW will be about 50 to 60 kg.
# What kind of raw material should be charged? It is important for the starting, because the initial density should not be too small (packing density). And the other question is, what kind of scrab it will be.
There are so many problems known with content of zinc (hot zinc dipped) and other materials. The lifetime of common refractory material is really small. And what is more important the security for the personal is not given without a strong exhaust system, due to the toxic steam. I expect this as a strong cost factor.
 
===Power Supply===
*50 kW for $1600 - [http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=200415768835&rvr_id=&crlp=1_263602_263622&UA=L*F%3F&GUID=1357ab741250a0265337bec7ff94d6a7&itemid=200415768835&ff4=263602_263622]
*20 kw STC 3 phase 120 - 480V, also 1 phase - generator - $692 -[http://cgi.ebay.com/20kw-STC-3-Phase-277-480-12-Wire-generator-Head-altern_W0QQitemZ160369799644QQcmdZViewItemQQptZBI_Generators?hash=item2556c8f1dc]
*50 kw STC 3 phase- $1300 - [http://cgi.ebay.com/50KW-STC-3-Phase-12-Wire-generator-alternator_W0QQitemZ160357088416QQcmdZViewItemQQptZBI_Generators?hash=item255606fca0]
**LifeTrac 55 hp can produce 38 kW with this head
 
===Melt Calculations===
[[Image:inductioncalc.jpg]]
 
==See Also==
* Original blog post: http://openfarmtech.org/weblog/?p=1373
* Furnace selection: http://www.articlesfactory.com/articles/hobbies/induction-furnace-and-cupola-furnace-information.html
* http://inductionheater.org/
* http://www.dansworkshop.com/electricity-and-electronics/induction-heating.htm
* Educypedia - Induction-related articles: http://www.educypedia.be/electronics/electricityinduction.htm
* Articles on electricity and electronics: http://www.allaboutcircuits.com/
* UFES: http://www.ufes.com/index.php?n=Foundry.FurnacesOvens
* induction furnaces are a mature technology. Many induction furnace patents are more than 20 years old, and therefore public domain. What is a good way to get a list of patents that have good information about making an induction furnace, that isn't diluted by hundreds of patents that happen to mention using induction furnaces?
** "channel type induction furnace" 1974 US Patent 3798344.
* Other technology: With the right techniques, a microwave oven can apparently heat glass to its melting point of 1,500 °C. (  [http://www.popsci.com/diy/article/2003-09/smelting-microwave PopSci], [http://www.wired.com/gadgetlab/2008/02/video-micowave/ Wired], [http://www.wonderhowto.com/topic/fusing-glass-with-microwave-oven/ Howto]). That is slightly more than melting point of steel (more or less 1,400 °C). Is it possible to use similar techniques to form small steel parts in a off-the-shelf microwave?[http://home.c2i.net/metaphor/mvpage.html] Would a thin layer of glass floating on the molten steel help block oxidation?
* Other technology: Is it possible to pre-heat the metal -- and the crucible -- with some kind of [[Solar Concentrators]], reducing the amount of electrical energy required to bring it the rest of the way up to melting temperature?
===DIY Furnaces===
*http://www.richieburnett.co.uk/indheat.html
*http://www.hvguy.4hv.org/ih/
*http://webpages.charter.net/dawill/tmoranwms/Elec_IndHeat1.html
* 1 kW Induction Furnace Kit: http://webpages.charter.net/dawill/tmoranwms/Elec_IndHeat8.html
*http://www.dansworkshop.com/electricity-and-electronics/induction-heating.htm
===Commercial===
*Commercial induction furnace power supplies from Superior Induction - [http://www.superiorinduction.com/?gclid=CO2fgNqPtZkCFRAhDQodqjeo5Q]
*EPRI works with induction - The EPRI Center for Materials Production at Carnegie Mellon, Pittsburgh, PA, 412-268-3243
 
===Forum Posts===
* You can start your own discussions on our [http://openfarmtech.org/weblog/forum/induction-furnace/ Open Source Induction Furnace Forum]
* CNC Zone - Induction furnace topic: http://www.cnczone.com/forums/showthread.php?t=13545
* Metal Casting Zone - Furnace Info: http://www.metalcastingzone.com/metal-casting-forum/casting-furnaces
* Metal and Metallurgy engineering Forum: http://www.eng-tips.com/threadminder.cfm?pid=330&page=1
* Electronics and electricity: http://forum.allaboutcircuits.com/
* Electronics: http://www.electro-tech-online.com/
If you think there are missing or incorrect details here, please help correct that.
 
 
[[Category:Induction Furnace]]
[[Category:Specifications]]
[[Category:Metalworks]]
[[Category:Fabrication]]

Latest revision as of 21:25, 11 September 2011

Redirect to:

Retrieved from "https://wiki.opensourceecology.org/index.php?title=Open_Source_Induction_Furnace_Project&oldid=40696"