Garage Door Opener Install: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
Programming: [https://docs.google.com/presentation/d/1IglMwlvzJzA5S6ePZJcBh-0rtOnXw41Hl-RiOQfvbNk/edit?slide=id.g33327038b48_0_0#slide=id.g33327038b48_0_0] | Programming: [https://docs.google.com/presentation/d/1IglMwlvzJzA5S6ePZJcBh-0rtOnXw41Hl-RiOQfvbNk/edit?slide=id.g33327038b48_0_0#slide=id.g33327038b48_0_0] | ||
= Genie 7055 Garage Door Opener LED Status Codes = | |||
Source - [https://chatgpt.com/share/69ab74fd-77e0-8010-9f81-7bc3ddb8b8dd] | |||
= Genie 7055 Garage Door Opener LED Status Codes = | |||
{| class="wikitable" | |||
! System State | |||
! Opener Round LED (Blue) | |||
! Opener Long LED (Purple) | |||
! Sensor LEDs (Red / Green) | |||
! Meaning | |||
! Typical Action | |||
|- | |||
| Normal operation (fully programmed, ready) | |||
| Solid Blue | |||
| Off | |||
| Red solid / Green solid | |||
| System powered and operating normally | |||
| None required | |||
|- | |||
| Programming mode entered | |||
| Flashing Blue | |||
| Off | |||
| Red solid / Green solid | |||
| User pressed SET/PROGRAM to begin programming | |||
| Continue programming steps | |||
|- | |||
| Ready to program remote | |||
| Flashing Blue | |||
| Flashing Purple | |||
| Red solid / Green solid | |||
| Opener waiting for remote signal | |||
| Press remote button to pair | |||
|- | |||
| Travel limit programming mode | |||
| Blue on | |||
| Purple flashing | |||
| Red solid / Green solid | |||
| System waiting for UP/DOWN limits to be set | |||
| Set open and close positions | |||
|- | |||
| Door opening or closing normally | |||
| Blue solid | |||
| Off | |||
| Red solid / Green solid | |||
| Normal door movement | |||
| None | |||
|- | |||
| Safe-T-Beam blocked | |||
| Blue solid | |||
| Off | |||
| Red solid / Green flashing | |||
| Beam interrupted or object in doorway | |||
| Remove obstruction | |||
|- | |||
| Safe-T-Beam misaligned | |||
| Blue solid | |||
| Off | |||
| Red flashing / Green off or flashing | |||
| Sensors not aligned | |||
| Realign sensors | |||
|- | |||
| Safe-T-Beam wiring fault | |||
| Blue solid | |||
| Off | |||
| Red off / Green off | |||
| Sensor wiring disconnected or damaged | |||
| Inspect wiring to sensors | |||
|- | |||
| Door will not close unless wall button held | |||
| Blue solid | |||
| Off | |||
| Red flashing or Green flashing | |||
| Safety beam not detected | |||
| Fix sensor alignment or wiring | |||
|- | |||
| Battery backup idle (AC power lost) | |||
| Off | |||
| Off | |||
| Red solid / Green solid | |||
| Opener powered only by battery and conserving energy | |||
| Restore AC power to opener | |||
|- | |||
| Battery backup operating | |||
| Blue dim or brief flash | |||
| Off | |||
| Red solid / Green solid | |||
| Door operating on battery backup | |||
| Restore AC power | |||
|- | |||
| System memory reset or limits not programmed | |||
| Blue flashing | |||
| Purple flashing | |||
| Red solid / Green solid | |||
| Travel limits missing | |||
| Perform travel limit setup | |||
|- | |||
| Obstruction detected during travel | |||
| Blue solid | |||
| Off | |||
| Red solid / Green solid | |||
| Door encountered resistance | |||
| Check tracks, rollers, springs, obstruction | |||
|} | |||
Latest revision as of 00:56, 7 March 2026
Programming: [1]
Genie 7055 Garage Door Opener LED Status Codes
Source - [2]
Genie 7055 Garage Door Opener LED Status Codes
| System State | Opener Round LED (Blue) | Opener Long LED (Purple) | Sensor LEDs (Red / Green) | Meaning | Typical Action |
|---|---|---|---|---|---|
| Normal operation (fully programmed, ready) | Solid Blue | Off | Red solid / Green solid | System powered and operating normally | None required |
| Programming mode entered | Flashing Blue | Off | Red solid / Green solid | User pressed SET/PROGRAM to begin programming | Continue programming steps |
| Ready to program remote | Flashing Blue | Flashing Purple | Red solid / Green solid | Opener waiting for remote signal | Press remote button to pair |
| Travel limit programming mode | Blue on | Purple flashing | Red solid / Green solid | System waiting for UP/DOWN limits to be set | Set open and close positions |
| Door opening or closing normally | Blue solid | Off | Red solid / Green solid | Normal door movement | None |
| Safe-T-Beam blocked | Blue solid | Off | Red solid / Green flashing | Beam interrupted or object in doorway | Remove obstruction |
| Safe-T-Beam misaligned | Blue solid | Off | Red flashing / Green off or flashing | Sensors not aligned | Realign sensors |
| Safe-T-Beam wiring fault | Blue solid | Off | Red off / Green off | Sensor wiring disconnected or damaged | Inspect wiring to sensors |
| Door will not close unless wall button held | Blue solid | Off | Red flashing or Green flashing | Safety beam not detected | Fix sensor alignment or wiring |
| Battery backup idle (AC power lost) | Off | Off | Red solid / Green solid | Opener powered only by battery and conserving energy | Restore AC power to opener |
| Battery backup operating | Blue dim or brief flash | Off | Red solid / Green solid | Door operating on battery backup | Restore AC power |
| System memory reset or limits not programmed | Blue flashing | Purple flashing | Red solid / Green solid | Travel limits missing | Perform travel limit setup |
| Obstruction detected during travel | Blue solid | Off | Red solid / Green solid | Door encountered resistance | Check tracks, rollers, springs, obstruction |