CEB Press/Manufacturing Instructions/Valve Mount: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
No edit summary
 
(5 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{Category=CEB press building instructions}}
{{Category=CEB press building instructions}}
{{Template:CEB Press Manufacturing Instructions Navbox}}
 
The valve mount holds the hydraulic solenoid valves to the primary arm.
=Part Information=
<html><iframe src="http://sketchup.google.com/3dwarehouse/mini?mid=a239d963ea082d1a1211da1f85706ccd&etyp=im&width=400&height=300" frameborder="0" scrolling="no" marginheight="0" marginwidth="0" width="400" height="300"></iframe></html>
 
=Tools required=
*The valve mount holds the hydraulic solenoid valves to the primary arm.
 
=Tools=
 
*Hole puncher with 13/16" Dies
*Hole puncher with 13/16" Dies
*Drill Press with 1/4" or larger bit.
 
=Materials required=  
*Drill Press with 5/16" or larger bit.
*1/4"x6" flatbar: 12"
 
=Diagrams=
*Center Punch
[[Image:valvemount.png|thumb|600px|The valve mount]]
 
=Fabrication instructions=
*Measuring Tape
#Find your hydraulic solenoid valve and locate its mounting holes on the back. Put the plate under it so that the mounts on the valve align with the top of the plate.  
 
#Use spray paint to mark the holes on the mount's location to the 6"x12" plate. Center punch them.
*Metal Marking Utensil
#Drill the holes to at least a 1/4" large (you might want to oversize them a bit, as it very difficult to get them in the perfect location.)
 
#Punch 13/16" holes at the bottom of the plate.
=Materials=  
 
*Steel plate 1/4" x 6" x 12"
 
*Solenoid Valve Subplate with Mount Angles
 
=Steps=
 
*Set the steel plate on a flat surface
 
*Position the solenoid valve subplate with mount angles over the plate such that its work port surface is flush with the top edge and square with the side edges of the steel plate.  
 
*Using the marking utensil and the center punch, mark then center punch the 4 aligned holes at the sides of the steel plate
 
*Drill 4 holes of 5/16" diameter at the marked points of the steel plate
 
*Punch 2 holes of 13/16" diameter that are centered 20cm from each other and 3cm from the bottom edge of the steel plate.
 
[[Image:ValveMount.png]]

Latest revision as of 00:30, 23 December 2011

Main > Housing and construction > CEB Press > CEB press building instructions

Part Information

  • The valve mount holds the hydraulic solenoid valves to the primary arm.

Tools

  • Hole puncher with 13/16" Dies
  • Drill Press with 5/16" or larger bit.
  • Center Punch
  • Measuring Tape
  • Metal Marking Utensil

Materials

  • Steel plate 1/4" x 6" x 12"
  • Solenoid Valve Subplate with Mount Angles

Steps

  • Set the steel plate on a flat surface
  • Position the solenoid valve subplate with mount angles over the plate such that its work port surface is flush with the top edge and square with the side edges of the steel plate.
  • Using the marking utensil and the center punch, mark then center punch the 4 aligned holes at the sides of the steel plate
  • Drill 4 holes of 5/16" diameter at the marked points of the steel plate
  • Punch 2 holes of 13/16" diameter that are centered 20cm from each other and 3cm from the bottom edge of the steel plate.

ValveMount.png

Retrieved from "https://wiki.opensourceecology.org/index.php?title=CEB_Press/Manufacturing_Instructions/Valve_Mount&oldid=49131"