Klipper: Difference between revisions
Jump to navigation
Jump to search
(Added a Category to the Page) |
(Added some more links under the "External Links" section) |
||
| Line 32: | Line 32: | ||
*[https://www.youtube.com/watch?v=T-knWbh1Gg8 A Video by the YouTube Channel "NERO 3D" Titled "Klipper Initial Setup : Making sure things are all good before printing" ] (~19 Minute Watch) (Does great documentation of a [[Machine Startup Procedure]] and all the "pre flight checks" ) | *[https://www.youtube.com/watch?v=T-knWbh1Gg8 A Video by the YouTube Channel "NERO 3D" Titled "Klipper Initial Setup : Making sure things are all good before printing" ] (~19 Minute Watch) (Does great documentation of a [[Machine Startup Procedure]] and all the "pre flight checks" ) | ||
*[https://www.reddit.com/r/klippers/comments/kuf9si/mainsail_vs_fluidd_vs_dw2/ A 2020 Reddit Post on "r/Klippers" Titled "Best Klipper UI Setup?" ] (Mainly Discusses Fluidd and Mainsail) | *[https://www.reddit.com/r/klippers/comments/kuf9si/mainsail_vs_fluidd_vs_dw2/ A 2020 Reddit Post on "r/Klippers" Titled "Best Klipper UI Setup?" ] (Mainly Discusses Fluidd and Mainsail) | ||
*[https://www.reddit.com/r/VORONDesign/comments/s35zda/ive_been_using_octoprint_for_a_long_time_but/ A 2022 Reddit Post on "r/[[Voron]]Design" Titled "I've been using octoprint for a long time but wondering if there is a convincing reason to switch to Fluidd or Mainsail?" | |||
[[Category: 3D Printing]] [[Category: Internet of Things]] | [[Category: 3D Printing]] [[Category: Internet of Things]] | ||
Revision as of 00:12, 23 January 2022
Basics
- An advanced FDM 3D Printer Firmware
- "Klipper is a 3d-Printer firmware. It combines the power of a general purpose computer with one or more micro-controllers." (The Project's Website)
Hardware
- 1.) A Single Board Computer (or in theory at least a used low-spec computer acquired for cheap?)
- Typically:
- A Raspberry Pi Zero if not utilizing 3D Printer Webcam functionalities
- A Raspberry Pi (need to grab what model is recommended, 2/3/4 etc) if utilizing the camera and/or other more intensive features
- Typically:
- 2.) A Standard Control Board (This no longer does the calculations of G Code to various electronics as this is offloaded to the Raspberry Pi)
- (Optional) 3.) A Klipperscreen ( Raspberry Pi Touchscreen + (Most Likely 3D Printed) Enclosure + Wiring )
Interfaces
Mainsail (Software)
Fluidd
- A Fork of Mainsail
- Supposedly More Actively Developed
Internal Links
External Links
- The Clipper Documentation Website
- The GitHub Page for Klipper
- The RepRap Wiki page on Klipper
- A Video by the YouTube Channel "NERO 3D" Titled "Klipper 3d Printer Firmware - What is it? Why do I want it?" ( ~18 Minute Watch)
- A Video by the YouTube Channel "NERO 3D" Titled "Klipperscreen - The Touchscreen Interface for Klipper" (~6 Minute Watch)
- A Video by the YouTube Channel "NERO 3D" Titled "Klipper Initial Setup : Making sure things are all good before printing" (~19 Minute Watch) (Does great documentation of a Machine Startup Procedure and all the "pre flight checks" )
- A 2020 Reddit Post on "r/Klippers" Titled "Best Klipper UI Setup?" (Mainly Discusses Fluidd and Mainsail)
- [https://www.reddit.com/r/VORONDesign/comments/s35zda/ive_been_using_octoprint_for_a_long_time_but/ A 2022 Reddit Post on "r/VoronDesign" Titled "I've been using octoprint for a long time but wondering if there is a convincing reason to switch to Fluidd or Mainsail?"