D3D Pro v23.12 Troubleshooting and Repair: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
No edit summary
(Finish through 2024/06/25)
Line 2: Line 2:
=Print & Maintenance Log=
=Print & Maintenance Log=
<nowiki>{{log|date=|time=|note=}}</nowiki>
<nowiki>{{log|date=|time=|note=}}</nowiki>
{{log|date=2024/06/25|time=11:11pm|note=Failed - '''Lost Z Steps'''}}
{{log|date=2024/06/25|time=11:07pm|note= Pen Case - Homing failed}}
{{log|date=2024/06/25|time=3:29am|note=Pen Case - Failed - underextrusion (?)}}
{{log|date=2024/06/25|time=2:58am|note=Pen Case - good start (?). Paused for filament strip. Am I printing too fast? Good again after pause. Nevermind - failed on filament stripping.}}
{{log|date=2024/06/25|time=2:52am|note=Pen Case - Failed - Z randomly losing steps during initial heatup.}}
{{log|date=2024/06/25|time=2:21am|note=Pen Case - Failed - Z offset too high.}}
{{log|date=2024/06/25|time=2:05am|note=Failed - stripping. '''Recaptured bed mesh'''}}
{{log|date=2024/06/25|time=1:59am|note=Failed - stripping. Adjusted Z offset.}}
{{log|date=2024/06/25|time=1:58am|note=Failed - Y axis skewed.}}
{{log|date=2024/06/25|time=1:55am|note=Failed - X homing. Endstop rotated and was angled too low.}}
{{log|date=2024/06/25|time=1:20am|note=Bj. S. P. 2 - Paused at start for stripped filament. Failure -  stripping, bed leveling(?)}}
{{log|date=2024/06/25|time=1:13am|note=Bj. S. P. 2 - 0.2mm layers - Failed - nozzle too close to bed. Forgot to set correct Z offset and save to EEPROM (again).}}
{{log|date=2024/06/25|time=1:11am|note=Bj. S. P. 2 - Moved to 0.2mm layer heights from 0.3mm to reduce throughput. Failed - probing.}}
---


{{log|date=2024/06/24|time=11:49pm|note=Bj. S. P. 2 - Failed - nozzle too close to bed - filament stripped. I forgot to save the previous bed offset; live adjusted Z to compensate and attempt recovery. '''X axis belt clamp is too low - damaging prints.''' Failure - Bed adhesion, underextrusion, filament stripping.}}
{{log|date=2024/06/24|time=11:49pm|note=Bj. S. P. 2 - Failed - nozzle too close to bed - filament stripped. I forgot to save the previous bed offset; live adjusted Z to compensate and attempt recovery. '''X axis belt clamp is too low - damaging prints.''' Failure - Bed adhesion, underextrusion, filament stripping.}}

Revision as of 12:15, 6 July 2024

Print & Maintenance Log

{{log|date=|time=|note=}}


2024/06/25 | 11:11pm

  • Failed - Lost Z Steps


2024/06/25 | 11:07pm

  • Pen Case - Homing failed


2024/06/25 | 3:29am

  • Pen Case - Failed - underextrusion (?)


2024/06/25 | 2:58am

  • Pen Case - good start (?). Paused for filament strip. Am I printing too fast? Good again after pause. Nevermind - failed on filament stripping.


2024/06/25 | 2:52am

  • Pen Case - Failed - Z randomly losing steps during initial heatup.


2024/06/25 | 2:21am

  • Pen Case - Failed - Z offset too high.


2024/06/25 | 2:05am

  • Failed - stripping. Recaptured bed mesh


2024/06/25 | 1:59am

  • Failed - stripping. Adjusted Z offset.


2024/06/25 | 1:58am

  • Failed - Y axis skewed.


2024/06/25 | 1:55am

  • Failed - X homing. Endstop rotated and was angled too low.


2024/06/25 | 1:20am

  • Bj. S. P. 2 - Paused at start for stripped filament. Failure - stripping, bed leveling(?)


2024/06/25 | 1:13am

  • Bj. S. P. 2 - 0.2mm layers - Failed - nozzle too close to bed. Forgot to set correct Z offset and save to EEPROM (again).


2024/06/25 | 1:11am

  • Bj. S. P. 2 - Moved to 0.2mm layer heights from 0.3mm to reduce throughput. Failed - probing.


---


2024/06/24 | 11:49pm

  • Bj. S. P. 2 - Failed - nozzle too close to bed - filament stripped. I forgot to save the previous bed offset; live adjusted Z to compensate and attempt recovery. X axis belt clamp is too low - damaging prints. Failure - Bed adhesion, underextrusion, filament stripping.


2024/06/24 | 11:46pm

  • Blackjack Shoe Plate 2 - probing failed, bed misaligned


2024/06/24 | 11:43pm

  • Failure to heat bed - M112 error


2024/06/24 | 11:38pm

  • R.T.T.P. - turned off linear advance @ ~10% - Print looking okay at 60% - some underextrusion early on. Print successful! Horizontal artiface appears in a repeating pattern every 7mm. (Primarily cosmetic issue). Printed this model in incorrect orientation


2024/06/24 | 11:11pm

  • R.T.T.P. - Paused @ skirt for stripped filament. Failed @ 5-10%. Stripped filament


2024/06/24 | 11:08pm

  • R.T.T.P. - Speed too high? Seemingly exceeding max volumetric flow rate. Failed - underextrusion


2024/06/24 | 10:45pm

  • Ringing tower test print - Cancelled - Forgot to adjust min. layer time


2024/06/24 | 10:24pm

  • Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black
Retrieved from "https://wiki.opensourceecology.org/index.php?title=D3D_Pro_v23.12_Troubleshooting_and_Repair&oldid=298292"