Power Cube II

Parts List

Last updated 26 August, 2010

Power Cube II engine

Breather cap

Suction strainer, 14 gpm

Suction strainer, 23 gpm

Hydraulic pump, 14 gpm

Frame

• 1/4"x4"x4" mild steel square tubing - 22 feet @$8.15/foot - $180 - 286 lb
• Quick attach system

Hydraulic and gasoline filler/breather.

Engine

• 18 hp Engine - $479 - [1]- 81 lb. Sorry, steam engine is forthcoming.
  • Note: engine spins counterclockwise (CCW) from PTO side, so pump must have clockwise (CW) rotation
• 27 hp engine - $750 - [2]
• Fuel tank filler and breather - [[3]]
• Fuel tank fuel line barb with shutoff
• Battery
• Starter solenoid
• Starter switch, shutoff switch - key with spring return?
• Battery cables
• Throttle cable
• Choke cable

Engine Coupling to Pump

• Coupler half, 5/8" - $10
• Coupler half, 1" - $10
• Solid spider - $14

Pump

• Hydraulic pump - 0.677 cu in, 5/8" keyed shaft, 10.1 gmp @3600 RPM, 3000 PSI max, 4000 RPM max - $180
• Pump outlet - SAE 10 to 1/2 NPTM straight - $1.89
• 1/2" quick coupler - same as above - $16
• Suction Hose
• 3/4 NPTM to hose barb elbow connector - $4.69
• 3/4 NPTM to hose barb straight connector for second PowerCube - $3.95
• Pump inlet - SAE 12 to 3/4 hose barb connector - $4.69

Engine Mounting and Pump Mount Plate

• Pump mount plate - 1/4"x6"x8"
• Engine mounting -

Pressure Bypass Safety Valve

• [1] 1/2" NPT Bypass valve - [4]
• [3] 1/2" Quick couplers - 1 complete for tee near pump, one going from return filter to tee, and male tip for return line. This gives one extra female quick coupler left over. This set of 3 QCs does not cover hoses going from and to the PowerCube.
• [4] 1/2" NPTF hex nip for one and other side of tee, on both tees - [5]
• [2] 1/2" NPTF tee - from outlet of pump to pressure bypass, and from bypass valve into return line filter - [6]

Reservoir

• Suction strainer, 1.5" - [7] - $20
  • Use this for single Power Cube
  • 1-1/2" NPT coupling for threading suction strainer into frame - found at big box hardware
• Suction strainer, 2" - [8] - $23
  • Use for dual Power Cubes
  • Use 2" coupler from bix box store to thread into Power Cube frame
• Hydraulic pump - 10 gpm at 3600 rpm, CW rotation - from Power Cube I - [9]
• Hydraulic pump - 14 gpm at 3600 rpm, CW rotation - from Power Cube I - [10]
• [1] 20 GPM return Line Filter - [11]
• [1] 3/4" quick coupler for return line to filter
• [1] 3/4" NPT Swivel for return line filter going into frame - [12]
• [2] 3/4" NPT hex nip on both sides of filter - [13]
• [1] 1"-3/4" NPT reducer bushing for frame receptacle for return filter - [14]
• [2] 1/2" quick couplers for main power lines

Hoses

• [1] 2 foot hose from pump outlet to return line filter - [15]
• 3/4" suction hose