D3D Pro v23.12 Troubleshooting and Repair: Difference between revisions
Jump to navigation
Jump to search
(Create new data collection page) |
(Finish through 2024/06/24) |
||
| Line 1: | Line 1: | ||
=Print & Maintenance Log= | =Print & Maintenance Log= | ||
<nowiki>{{log|date=|time=|note=}}</nowiki> | |||
{{log|date=2024/06/24|time=11:49pm|note=Bj. S. P. 2 - Failed - nozzle too close to bed - filament stripped. I forgot to save the previous bed offset; live adjusted Z to compensate and attempt recovery. '''X axis belt clamp is too low - damaging prints.''' Failure - Bed adhesion, underextrusion, filament stripping.}} | |||
{{log|date=2024/06/24|time=11:46pm|note=Blackjack Shoe Plate 2 - probing failed, bed misaligned}} | |||
{{log|date=2024/06/24|time=11:43pm|note=Failure to heat bed - M112 error}} | |||
{{log|date=2024/06/24|time=11:38pm|note=R.T.T.P. - turned off linear advance @ ~10% - Print looking okay at 60% - some underextrusion early on. Print successful! Horizontal artiface appears in a repeating pattern every 7mm. (Primarily cosmetic issue). Printed this model in incorrect orientation}} | |||
{{log|date=2024/06/24|time=11:11pm|note=R.T.T.P. - Paused @ skirt for stripped filament. Failed @ 5-10%. Stripped filament}} | |||
{{log|date=2024/06/24|time=11:08pm|note=R.T.T.P. - Speed too high? Seemingly exceeding max volumetric flow rate. Failed - underextrusion}} | |||
{{log|date=2024/06/24|time=10:45pm|note=Ringing tower test print - Cancelled - Forgot to adjust min. layer time}} | |||
{{log|date=2024/06/24|time=10:24pm|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}} | {{log|date=2024/06/24|time=10:24pm|note=Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black}} | ||
Revision as of 12:01, 6 July 2024
Print & Maintenance Log
{{log|date=|time=|note=}}
2024/06/24 | 11:49pm
- Bj. S. P. 2 - Failed - nozzle too close to bed - filament stripped. I forgot to save the previous bed offset; live adjusted Z to compensate and attempt recovery. X axis belt clamp is too low - damaging prints. Failure - Bed adhesion, underextrusion, filament stripping.
2024/06/24 | 11:46pm
- Blackjack Shoe Plate 2 - probing failed, bed misaligned
2024/06/24 | 11:43pm
- Failure to heat bed - M112 error
2024/06/24 | 11:38pm
- R.T.T.P. - turned off linear advance @ ~10% - Print looking okay at 60% - some underextrusion early on. Print successful! Horizontal artiface appears in a repeating pattern every 7mm. (Primarily cosmetic issue). Printed this model in incorrect orientation
2024/06/24 | 11:11pm
- R.T.T.P. - Paused @ skirt for stripped filament. Failed @ 5-10%. Stripped filament
2024/06/24 | 11:08pm
- R.T.T.P. - Speed too high? Seemingly exceeding max volumetric flow rate. Failed - underextrusion
2024/06/24 | 10:45pm
- Ringing tower test print - Cancelled - Forgot to adjust min. layer time
2024/06/24 | 10:24pm
- Ringing tower test print - Cancelled - Print speeds not high enough - Polymaker PLA Black