For the fruition of LifeTrac II is with this plenipotentiary abridged parts list

Complete detailed parts list [1]

Hydraulics

Note that the following list involves 2 loaders. For a simpler version, a single front loader is sufficient. Two loaders are used for extreme flexibility.

(download Blender file here)

Main

Parts from Surplus Center:

Note: Green indicates finalized shopping list from Surplus Center. Blue indicates list from McMaster Carr. Red is Dalton Hydralics. See Parts Sourcing for contact information.

[8] flange Bearings - [2]
[2] Front Loader cylinders - 36" - $174 - 48 5/8" retracted length - [3]
[4] 3/8 NPTM x 1/2 NPTF 90 SWIVEL [4] for Front Loader Cylinders up to hose
1. 4.9 square inch area at 2500 PSI implies 12000 lb of force for each cylinder
[4] QA plate hydraulic cylinders ~~& 2 Rear Loader~~ [5]
[4] Motors - [6]
1. [8] SAE M 10 to NPT M 1/2" for Ports [7]
2. [4] SAE 4M TO 1/4" NPTM CONNECTOR for Case Drains [8]
3. [8] 1/2" QC for Motors [9]
4. [4] 1/4" QC for motors [10]
[4] 1-1/4" shaft couplers - [11]
[1] 1-3/8" 6T fully splined shafting - [12]
[2] Female 1-3/8" 6T spline coupling - [13], $30 each
[12] 1.875" double split shaft collars - [14]
1. got 10 double split
2. got 2 single split - [15]

Valves

[1] 3-spool motor valve, 25 gpm - [16], $288
[4] 1/2" Quick Couplers [17] - for motor valve work ports
[4] 1/2" NPT M to NPT M 90deg Elbow for Motor Valve working ports [18] - for 2 sets of work ports to wheel motors
[4] 3/4" NPT quick couplers - Dalton Hydraulics - 2 for in/out, 2 for auxiliary work ports
[2] 1/2 NPT hex nipples [19]-for auxiliary pair of motor valve work ports
[2] 3/4 NPT hex nips [20] - in and out of valve
[2] 3/4 NPT to 1/2 NPT bushing [21] - auxiliary work ports

OSE Danfoss Black 2 Spool

[4] SAE 8M TO 1/2" NPTM CONNECTOR for working ports [22]
[6] 1/2" NPT QUICK COUPLER F/F S20-4 [23]
[1] SAE 10 PLUG for OSE BLACK 2 Spool [24]
[2] SAE 10M TO 1/2" NPT CONNECTOR [25]

3 Spool Husco

[1] 3/4" NPT quick couplers - Dalton Hydraulics - 1 pair for inlet
[1] 3/4" NPT nip - [26] - for inlet
[3] 1/2" nip for return cross [27]
[1] 1/2"-1/4" bushing - to accept case drain return [28]
[2] quick coupler pairs for return line - [29]
Pipe cross fitting on the return line to accommodate case drain return - [30]

2 Spool Prince Valve

~~[1] 3/4" Quick Coupler for outlet (already included in central 3-spool motor valve)~~
[2] 3/4" NPT nip for inlet/outlet - [31]
[1] 3/4" NPT tee (already have these) for inlet
[2] 3/4" to 1/2" bushings - [32]
[1] 1/2" NPT male elbow - [33]
[2] 1/2" quick coupler pairs - [34]

Cushion Valves

[2] 1/2 NPT 30 GPM 1500-3000 PSI HYD CUSHION VALVES - [35]
[4] 1/2" male QC tips to plug into valves, which already have female QCs [36]
[2] 1/2 NPTM x 1/2 NPTF swivel [37] for cushion valve to mount tees, for separating to right and left cylinders; only one swivel needed per cushion valve
[4] 1/2" nip - [38] - going from between swivel and tee.
[4] NPTF Tee [39]- 4 for loaders only, not QA plates

Power Cube

[1] Coupler half, 5/8" - $10
[1] Coupler half, 1" - $10
[1] Solid spider - $14
[1] Breather cap - [40] - $8
- [1] 3/4 NPT coupling - found at big box hardware stores
[1] Suction strainer, 2" tp 1-1/4" - [41] - $23
- Use for dual Power Cubes
- [1] Use 2" coupler from bix box store to thread into Power Cube frame
[1] Pressure relief for power cube bypass- [42]