All public logs

Combined display of all available logs of Open Source Ecology. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

• 10:56, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:Rubber spacers01.jpg (Spacers glued to HBP.)
• 10:54, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:Rubber spacers00.jpg (Doubling the thickness.)
• 10:44, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:Y1 x square.jpg (Square mating of carriage of Y1 and short idler side of X.)
• 10:40, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:End stop y modified.jpg (Extension added on Y1 carriage to stop X before extruder hits Y1 motor. By doing this travel range on X is increased by 10mm.)
• 10:36, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:End stop x modified.jpg (Modified end stop on X to increase travel range.)
• 10:22, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:X axis parallel.jpg (Checking that x-axis is parallel to frame after installation.)
• 10:20, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:Rubber spacers.jpg (Heat resistant rubber spacers for heated bed.)
• 05:49, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Clearance Y1 X.jpg (Clearance in the Y1-X corner)
• 05:46, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Range y.jpg (Range of movement on Y-axis. 188mm)
• 05:45, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Range X.jpg (Range of movement on X-axis. 191 mm)
• 05:42, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Sensor on.jpg (Inductive sensor in place.)
• 05:40, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Heat sink ext01.jpg (Vanes)
• 05:38, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Heat sink ext00.jpg (Trimmed extruder heat sink)
• 05:37, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Heat sink ext.jpg (Trimming extruder heat sink)
• 05:34, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Inductive install.jpg (Installing inductive sensor)
• 05:31, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Termistor connector.jpg (EO and HBP termistors in one connector. Recycle.)
• 05:23, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Axes configuration.jpg (Positions of axes and motors.)
• 05:20, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Install x.jpg (Access hole to tighten the bottom screw holding X-axis to the carriage.)
• 05:15, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Belt tension.jpg (Tensioning belt by feel.)
• 05:12, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:One peg.jpg (Belt-tightening peg)
• 05:10, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:M6x30-2.jpg (Trimmed off 2mm from M6x30mm SS screws.)
• 11:15, 3 January 2018 Cabeza de Pomelo talk contribs uploaded File:All axes frame.jpg (The disposition of all axes on the metal frame.)
• 09:13, 1 January 2018 Cabeza de Pomelo talk contribs uploaded File:Controller wiring.jpg (Some of the wires to the controller.)
• 09:11, 1 January 2018 Cabeza de Pomelo talk contribs uploaded File:Soldering inductive sensor.jpg (Soldering inductive sensor's wires to Dupont end in the correct sequence.)
• 09:08, 1 January 2018 Cabeza de Pomelo talk contribs uploaded File:Inducive sensor dupont.jpg (Setting up wires to solder Dupont connector end to inductive sensor wiring.)
• 09:05, 1 January 2018 Cabeza de Pomelo talk contribs uploaded File:Sequence dupont.jpg (Changing wire sequence in Dupont connector.)
• 22:32, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:X y y.jpg (X and Y axes)
• 22:29, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Pulley alignment.jpg (Correct alignment.)
• 22:26, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Motor pulley ok.jpg (Correct placement of pulley.)
• 22:24, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Motor pulley ref.jpg (Used a bearing as a reference to accurately place the pulleys on the motors.)
• 22:21, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Short idler tight.jpg (A gap of around about 0.5mm must be seen between the two bearings)
• 22:16, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:HBP temp.jpg (Maximum temperature reached by HBP without regulation.)
• 22:13, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Idler flanges on.jpg (Printed flanges for idler bearings.)
• 22:08, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Square interface carriage.jpg (Proper alignment of parts after gluing the magnets.)
• 22:05, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Magnets epoxy.jpg (Beads of epoxy on extruder interface.)
• 22:02, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Magnets extruder interface.jpg (Sticking the magnets of the extruder interface to the carriage assembly before gluing.)
• 21:58, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Magnets taped.jpg (Magnets being held down by tape while gluing.)
• 21:54, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Bridging scraped.jpg (Scraping of the loose layer in a bridged gap of the print.)
• 21:50, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Bridging filaments.jpg (Lack of adhesion between the first layer the bottom of a magnet socket and the following layer due to the printer having to bridge the gap.)
• 05:27, 27 December 2017 Cabeza de Pomelo talk contribs uploaded File:Aus spacer idler.jpg (Detail of the spacers on the idler side.)
• 05:26, 27 December 2017 Cabeza de Pomelo talk contribs uploaded File:Aus spacer motor.jpg (Detail of the spacers on the motor side.)
• 05:23, 27 December 2017 Cabeza de Pomelo talk contribs uploaded File:Aus spacers.jpg (Spacers to mount axes using the bolts that squeeze the end sandwiches (motor and idler) together.)
• 05:21, 27 December 2017 Cabeza de Pomelo talk contribs uploaded File:Aus holes misplaced.jpg (Redrilled holes. Displaced 6mm to be able to drill next to the first set.)
• 05:18, 27 December 2017 Cabeza de Pomelo talk contribs uploaded File:Aus hole marks.jpg (Markings placed with template tool. D3D Australia)
• 11:25, 26 December 2017 Cabeza de Pomelo talk contribs uploaded File:D3DAustralia Axes Spacer.png (Spacers that allow for a 2mm separation between D3D frame and all axes assemblies when affixed with bolts.)
• 11:18, 26 December 2017 Cabeza de Pomelo talk contribs uploaded File:D3DAustralia Holes Template.png (Template to accurately place guide marks for the holes where the Y axes mount to the frame of the printer.)
• 12:16, 23 December 2017 Cabeza de Pomelo talk contribs uploaded File:Linear bearing tape00.jpg (Measuring increased diameter on a linear bearing.)
• 12:14, 23 December 2017 Cabeza de Pomelo talk contribs uploaded File:Linear bearing tape.jpg (Linear bearings with increased diameter.)
• 12:00, 23 December 2017 Cabeza de Pomelo talk contribs uploaded File:Holes template01.jpg (Template to place holes on the D3D frame's corners.)
• 11:59, 23 December 2017 Cabeza de Pomelo talk contribs uploaded File:Holes template02.jpg (Template to place holes on the D3D frame's corners.)