April 2011 Production Run Hydraulics BOM

From Open Source Ecology
Jump to: navigation, search

Generator (X1)

  1. [1] hydraulic motor for direct 1800RPM generator drive - [1]
  2. [1] 5/8" coupler - [2]

Other (X5)

  1. [1] Power Cube Throttle Cable - [3] - need 5
  2. Battery Cable - [4] - need 3
  3. Starter Solenoid - [5] - need 5
  4. Key Switch - [6] - need 5
  5. Fuel Hose Barb - [7] - need 5

Tractor (x3)

See Parts Sourcing for contact information. Note: this includes hydraulics and balance of system after metal.

  1. [8] 1-7/8" Flange Bearings - [8] ; plus BearingsOn plus Big Bearing Store
  2. [2] Front Loader cylinders - 36" - $174 - 48 5/8" retracted length - [9] & [2] of [[10]]
  3. [2] QA Plate Cylinders - [11]
  4. [4] 3/8 NPTM x 1/2 NPTF swivel [12] for QA Plate cylinders
  5. [4] 3/8 NPTM x 1/2 NPTF 90 swivel [13] for Loader cylinders
  6. [4] Motors - [14]
    1. [8] SAE M 10 to NPT M 1/2" for Ports [15]
    2. [4] SAE 4M TO 1/4" NPTM CONNECTOR for Case Drains [16]
    3. [8] 1/2" QC for Motors [17]
    4. [4] 1/4" QC for motors [18]
  7. [2] 1-1/4 SHAFT COUPLER W 5/16" KEYWAY - [19]
  8. [1 1/3] 1-3/8" 6T fully splined shafting - [20]
  9. [2] Female 1-3/8" 6T spline coupling - [21], $17 each
  10. [12] 1.875" double split shaft collars - [22]
  11. Double split - $11 - [23]
  12. Double split - $9 -Houston Bearing
  13. Double split - $9 free ship - [24]
  14. Single split - [25]

Motor Valves (X3)

  • [1] 3-spool motor valve, 25 gpm - [26], $288
  • [3] 3/4" Nips [27] (includes cylinder valve, outlet tee)
  • [1] 3/4" swivel - [28]
  • [2] 3/4" Quick Couplers for one set of motor valve work ports - Dalton Hydraulics
  • [4] 1/2" Swivels for work ports [29] - for 2 sets of work ports to wheel motors
  • [2] 3/4" tee for inlet + outlet - [30]
  • [1] 3/4"-1/4" reducer for outlet - [31]
  • [1] 3/4" elbow for inlet - [32]
  • [1] 1/4" nip for case drain of pulverizer - [33]
  • [1] 1/4" Quiuck Coupler - [34]
  • [2] 30 GPM check valves for inlet - [35]
  • [2] 3/4" QC for inlet - Dalton
  • [5] 3/4"nips for inlet including valve in/out - [36]
  • [2] 1/2 NPT hex nipples [37]-for auxiliary pair of motor valve work ports
  • [2] 3/4 NPT to 1/2 NPT bushing [38] - auxiliary work ports - NA

Loader Valve (X3)

  • [1] Prince 2 Spool Valve - [39] $189
  • [1] 3/4" NPT nip for outlet - [40]
  • [4] 1/2" Swivels for work ports [41] - for 2 sets of work ports to wheel motors
  • [1] 3/4" QC for outlet
  • [2] 1/2" tees to split to 2 cylinders - [42]

Cushion Valve (X3)

  • [1] 1/2 NPT 30 GPM 1500-3000 PSI HYD CUSHION VALVES - [43]
  • [6] 1/2" swivels [44] - 4 valve outlet + 2 cushion valve
  • [2] 1/2" nip - [45] - going from between swivel and tee
  • [4] NPTF Tee [46]- (includes QA plates

Power Cube (x5)

  • [1] Pump - 0.98 cu in - [47]
  • [1] 3/4" coupler for exit - Dalton
  • [1] 3/4" breather cap -[48] - $13
  • [1] Filler Cap - [49]
  • [1] SAE 12 in to 3/4 hosebarb- [50] - GOT 1 FOR TESTING
  • [1] SAE 10 out to 1/2 NPT - [51]
  • [1] 3/4 to 1/2 reducer bushing - NA
  • [1] Coupler half, 5/8" - $10
  • [1] Coupler half, 1 1/8" - $10
  • [1] Solid spider - $14
  • [1] Suction strainer, 2" to 1-1/4" - [52] - $23
  • 1" female coupling into frame
  • [1] 1" nip to filter - [53]
  • [1] 30 GPM return Line Filter - [54] - 5 total of these
  • [1] 1"-3/4" reducer bushing - [55]
  • [1] 3/4" tee - [56]
  • [2] 3/4" nip - [57]
  • [1] 30 gpm Quick Coupler to return line
  • [1] 3/4"-1/4" NPT reducer bushing for case drain - [58]
  • [1] 1/4" nip - [59]
  • [1] 1/4" quick couplers for case drain - [60]

Soil Pulverizer (x1)

  • [1] 7.6 cu in hydraulic PTO motor - [61]
  • [2] 1-7/8" bearings - []
  • [1] 6 tooth spline coupler - [62] (enough for 3)
  • [4] 30 gpm Quick Coupler - Dalton
  • [2] SAE 10 to 1/2 NPT swivel - [63]
  • [1] SAE 4 to 1/4 NPT swivel- [64]

Hoses

Soil Pulverizer (x1)

  • [2] 1/2"x12' hose - [65]
  • [1] 1/4"x12' hose - [66]

Power Cube (x1 bc it's broken down)

  • [4] 10 foot hoses - [67]
  • [6] 8 foot hoses - [68]

Motor Valves (x3)

  • [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of the valves [69]
  • [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of front motors [70]
  • [4] 1/2 X 1/2 X 1/2 NPTF TEE [71]
  • [4] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for rear motors [72]

Motor Case Drains (x3)

  • [2] 1/4" X 60" NPTM 2750 PSI HYD HOSE to run parallel with tractor sides [73]
  • [1] 1/4" X 72" hose return to Power Cube [74]
  • [1] 1/4" X 36" NPTM 2750 PSI HYD HOSE to Rear Motors [75]
  • [3] 1/4 X 1/4 X 1/4 NPTF TEE [76]
  • [3] 1/4 NPT hex nipples [77]

Front Loader (x3)

  • [2] 1/2" X 12" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE from Valves to Cushion [78]
  • [2] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for left front loader cylinder [79]
  • [1] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [80]
  • [1] 1/2" X 60" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [81]

QA Cylinder (x3)

  • [2] 1/2" nips - going from cylinder swivels to tees - [82]
  • [2] 1/2" NPTF tees - from cylinder to hoses - [83]
  • [2] 1/2" X 48" NPTM 3000 PSI HYD HOSE [84]
  • [1] 1/2" X 120" NPTM 3000 PSI HYD HOSE [85]
  • [1] 1/2" X 144" NPTM 3000 PSI HYD HOSE [86]

Retrieved from "https://wiki.opensourceecology.org/index.php?title=April_2011_Production_Run_Hydraulics_BOM&oldid=44745"