CEB Press v16.09/SCAD Files: Difference between revisions
Jump to navigation
Jump to search
(→A1) |
(→F8) |
||
| (14 intermediate revisions by the same user not shown) | |||
| Line 236: | Line 236: | ||
==F1== | ==F1== | ||
Welds to: F2, F3 | |||
Bolts to: F9 | |||
Abuts: A2 | |||
<nowiki> | <nowiki> | ||
| Line 274: | Line 280: | ||
</nowiki> | </nowiki> | ||
==F2== | |||
Welds to: F1, F4, F6 | |||
<nowiki> | <nowiki> | ||
| Line 302: | Line 309: | ||
</nowiki> | </nowiki> | ||
==F3== | |||
Welds to: F1 | |||
Bolts to: F12 | |||
<nowiki> | <nowiki> | ||
| Line 338: | Line 348: | ||
==F4== | ==F4== | ||
Welds to: F2, F5 | |||
Bolts to: F9 | |||
<nowiki> | <nowiki> | ||
| Line 395: | Line 409: | ||
==F5== | ==F5== | ||
Welds to: F4 | |||
Bolts to: A1 | |||
<nowiki> | <nowiki> | ||
| Line 431: | Line 449: | ||
} //end module | } //end module | ||
</nowiki> | </nowiki> | ||
==F6== | ==F6== | ||
some errors of symmetry in source dxf drawing. made some assumptions. need to check fit with interfacing parts. | some errors of symmetry in source dxf drawing. made some assumptions. need to check fit with interfacing parts. | ||
Welds to: F2, F7 | |||
Bolts to: F9 | |||
<nowiki> | <nowiki> | ||
| Line 470: | Line 491: | ||
</nowiki> | </nowiki> | ||
==F8== | |||
Welds to: F9, F10 | |||
Bolts to: Rub Plate ? | |||
<nowiki> | <nowiki> | ||
| Line 525: | Line 549: | ||
</nowiki> | </nowiki> | ||
==F9== | |||
Welds to: F8, F11 | |||
Bolts to: F1, F4, F6 | |||
Abuts: A1 ?, A2 ?, F12 | |||
<nowiki> | <nowiki> | ||
| Line 585: | Line 614: | ||
==F10== | ==F10== | ||
Welds to: F8? | |||
<nowiki> | <nowiki> | ||
| Line 595: | Line 626: | ||
==F11== | ==F11== | ||
Welds to: F9 | |||
<nowiki> | <nowiki> | ||
| Line 619: | Line 652: | ||
} //end module | } //end module | ||
</nowiki> | </nowiki> | ||
=Arms= | =Arms= | ||
Latest revision as of 02:04, 31 May 2017
work in progress
creating an OpenSCAD replica of v16.09
CEB Press v16.09/SCAD Files/Parametric
Frame
Assembly
F4x=31; //?why not just 22?
F4y=11;
F4z=0.5;
F4basex=25;
F6x=22.1875; //?why not just 22?
F6y=8;
F6z=0.5;
F8x=43.5;
F8y=6;
F8z=0.5;
F9x=43.5;
F9y=4.5;
F9z=0.5;
$fn=20; //render final model at 100
// ----------------------- //
translate([0,(F8y/2)+F6z,20.472]) //Z from F9// //adjust with cylinder length//
rotate([90,0,0])
F4(); //?group with F5?
translate([0,-(F8y/2),20.472])
rotate([90,0,0])
F4();
translate([0,(F8y/2)+F6z,0])
rotate([90,0,0])
F6();
translate([0,-(F8y/2),0])
rotate([90,0,0])
F6();
translate([1.9-8.5,0,0]){
rotate([0,0,90]){
translate([(F8y/2),F8z,0])
rotate([90,-90,0])
F8();
translate([(F8y/2)+(F9z/2)-(F8z/2),0,0])
rotate([0,-90,0])
F9();
translate([-(F8y/2)+(F9z/2)+(F8z/2),0,0])
rotate([0,-90,0])
F9();
}
}
translate([-1.9+8.5,0,0]){
rotate([0,0,-90]){
translate([(F8y/2),F8z,0])
rotate([90,-90,0])
F8();
translate([(F8y/2)+(F9z/2)-(F8z/2),0,0])
rotate([0,-90,0])
F9();
translate([-(F8y/2)+(F9z/2)+(F8z/2),0,0])
rotate([0,-90,0])
F9();
}
}
// ----------------------- //
module F4(){
difference(){
translate([-(F4x/2),0,0])
cube([F4x,F4y,F4z]);
translate([-(F4x/2),0,0])
cuts();
translate([(F4x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([0,0,0])
cube([3,5.375,F4z]);
translate([0,5.375,0])
difference(){
cube([3,5.125,F4z]);
translate([3,0,0])
rotate([0,0,atan(3/5.125)])
cube([10,10,F4z]);
}
translate([(F4x/2)-13.6375,F4y-0.5,0])
mirror([1,0,0])
cube([(F4x/2)-13.6375,0.5,F4z]);
translate([(F4x/2)-13.6375,F4y-0.625,0])
cube([2,0.625,F4z]);
translate([(F4x/2)-0.8125,F4y-0.5,0])
cube([0.8125,0.5,F4z]);
translate([(F4x/2)-1.0625,F4y-0.625,0])
cube([0.25,0.625,F4z]);
translate([(F4x/2)-9.8125,7.185,0]) //?part ycentered 7.5?
cube([1.125,0.625,F4z]); //?interfaces with what? ?part F2?
translate([(F4x/2)-8.5,2,0])
cylinder(h = F4z, r = 0.5025); //diameter 1.0?
translate([(F4x/2)-8.5,6,0])
cylinder(h = F4z, r = 0.5025);
translate([(F4x/2)-8.5,9,0])
cylinder(h = F4z, r = 0.5025);
} //end module
}
module F6(){
difference(){
translate([-(F6x/2),0,0])
cube([F6x,F6y,F6z]);
translate([-(F6x/2),0,0])
cuts();
translate([(F6x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([1.26,F6y-0.5,0]) //?xdistance from center?
cube([1.125,0.5,F6z]); //?interfaces with what?
translate([(F6x/2)-1.125,F6y-3.22,0])
cube([2.25,3.22,F6z]);
translate([F6x/2,F6y-3.22,0])
cylinder(h = F6z, r = 1.125);
translate([(F6x/2)-8.5,2,0])
cylinder(h = F6z, r = 0.38); //diameter 0.76?
translate([(F6x/2)-8.5,6,0])
cylinder(h = F6z, r = 0.38);
} //end module
}
module F8(){
difference(){
cube([F8x,F8y,F8z]);
translate([-0.0625,0,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([14.5-0.0625,0,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([14.5+14.5-0.0625,0,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([-0.0625,F8y,0])
mirror([0,1,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([14.5-0.0625,F8y,0])
mirror([0,1,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([14.5+14.5-0.0625,F8y,0])
mirror([0,1,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
hull(){
translate([23.34,3,0]) //?x interfaces with what?
cylinder(h = F8z, r = 0.5);
translate([23.6,3,0])
cylinder(h = F8z, r = 0.5);
}
hull(){
translate([30.34,3,0]) //?x interfaces with what?
cylinder(h = F8z, r = 0.5);
translate([30.6,3,0])
cylinder(h = F8z, r = 0.5);
}
}
} //end F8 module
module F9(){
difference(){
cube([F9x,F9y,F9z]);
translate([7.25,0,0])
cornerjoint(7.25,0.625,0.25,0.5,0.125);
translate([14.5+7.25,0,0])
cornerjoint(7.25,0.625,0.25,0.5,0.125);
translate([14.5+14.5+7.25,0,0])
cornerjoint(7.25,0.625,0.25,0.5,0.125);
translate([0,F9y-0.5625,0])
cube([0.53125,0.5625,F9z]);
translate([19.96875,F9y-0.5625,0])
cube([0.5625,0.5625,F9z]);
translate([31.3,F9y-1.4,0])
cube([6.4,1.4,F9z]); //?interfaces with what?
translate([F9x-0.5,F9y-0.5625,0])
cube([0.5,0.5625,F9z]);
translate([2,1.9,0]) //?x interfaces with what? ?1.9?
cylinder(h = F9z, r = 0.38);
translate([6,1.9,0]) //?x interfaces with what?
cylinder(h = F9z, r = 0.38);
translate([22.472,1.9,0]) //??.472?? ?interfaces with what?
cylinder(h = F9z, r = 0.5025);
translate([26.472,1.9,0])
cylinder(h = F9z, r = 0.5025);
translate([29.472,1.9,0])
cylinder(h = F9z, r = 0.5025);
translate([39,1.9,0]) //?x interfaces with what?
cylinder(h = F9z, r = 0.38);
translate([42,1.9,0]) //?x interfaces with what?
cylinder(h = F9z, r = 0.38);
}
} //end F9 module
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,F9z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,F9z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,F9z]);
}
} //end cornerjoint module
F1
Welds to: F2, F3
Bolts to: F9
Abuts: A2
F1x=24.2;
F1y=6;
F1z=0.5;
$fn=20; //render final model at 100
projection(cut = true) //use projection to create 2D DXF files
difference(){
translate([-(F1x/2),0,0])
cube([F1x,F1y,F1z]);
translate([-(F1x/2),0,0])
cuts();
translate([(F1x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
cube([0.5,0.5,F1z]);
translate([0.5,0,0])
cube([0.7875,0.625,F1z]);
translate([0,F1y-0.25,0])
cube([0.4,0.25,F1z]);
translate([2.2875,F1y-0.5,0])
cube([1.125,0.5,F1z]);
translate([11.0375,0,0])
cube([0.8125,0.625,F1z]);
translate([11.85,0,0])
cube([0.25,0.5,F1z]);
translate([3.6,1.5,0])
cylinder(h = F1z, r = 0.375);
translate([3.6,4.5,0])
cylinder(h = F1z, r = 0.375);
translate([6.1925,2.465,0])
cylinder(h = F1z, r = 0.6);
} //end module
F2
Welds to: F1, F4, F6
F2x=19.5;
F2y=3.5;
F2z=0.5;
$fn=20; //render final model at 100
projection(cut = true) //use projection to create 2D DXF files
difference(){
translate([-(F2x/2),0,0])
cube([F2x,F2y,F2z]);
translate([-(F2x/2),0,0])
cuts();
translate([(F2x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([1,F2y-0.625,0])
cube([0.125,0.625,F2z]);
translate([1.125,F2y-0.5,0])
cube([8.625,0.5,F2z]);
} //end module
F3
Welds to: F1
Bolts to: F12
F3x=23.75;
F3y=3.5;
F3z=0.5;
$fn=20; //render final model at 100
projection(cut = true) //use projection to create 2D DXF files
difference(){
translate([-(F3x/2),0,0])
cube([F3x,F3y,F3z]);
translate([-(F3x/2),0,0])
cuts();
translate([(F3x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([1,0,0])
cube([1,0.625,F3z]);
translate([2,0,0])
cube([1,0.5,F3z]);
translate([3,0,0])
cube([5.875,0.625,F3z]);
translate([8.875,0,0])
cube([1,0.5,F3z]);
translate([9.875,0,0])
cube([1,0.625,F3z]);
translate([5.375,1.75,0])
cylinder(h = F3z, r = 0.5);
} //end module
F4
Welds to: F2, F5
Bolts to: F9
F4x=31; //?why not just 22?
F4y=11;
F4z=0.5;
F4basex=25;
$fn=20; //render final model at 100
projection(cut = true) //use projection to create 2D DXF files
difference(){
translate([-(F4x/2),0,0])
cube([F4x,F4y,F4z]);
translate([-(F4x/2),0,0])
cuts();
translate([(F4x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([0,0,0])
cube([3,5.375,F4z]);
translate([0,5.375,0])
difference(){
cube([3,5.125,F4z]);
translate([3,0,0])
rotate([0,0,atan(3/5.125)])
cube([10,10,F4z]);
}
translate([(F4x/2)-13.6375,F4y-0.5,0])
mirror([1,0,0])
cube([(F4x/2)-13.6375,0.5,F4z]);
translate([(F4x/2)-13.6375,F4y-0.625,0])
cube([2,0.625,F4z]);
translate([(F4x/2)-0.8125,F4y-0.5,0])
cube([0.8125,0.5,F4z]);
translate([(F4x/2)-1.0625,F4y-0.625,0])
cube([0.25,0.625,F4z]);
translate([(F4x/2)-9.8125,7.185,0]) //?part ycentered 7.5?
cube([1.125,0.625,F4z]); //?interfaces with what? ?part F2?
translate([(F4x/2)-8.5,2,0])
cylinder(h = F4z, r = 0.5025); //diameter 1.0?
translate([(F4x/2)-8.5,6,0])
cylinder(h = F4z, r = 0.5025);
translate([(F4x/2)-8.5,9,0])
cylinder(h = F4z, r = 0.5025);
} //end module
F5
Welds to: F4
Bolts to: A1
F5x=31.4;
F5y=3.5;
F5z=0.5;
$fn=20; //render final model at 100
projection(cut = true) //use projection to create 2D DXF files
difference(){
translate([-(F5x/2),0,0])
cube([F5x,F5y,F5z]);
translate([-(F5x/2),0,0])
cuts();
translate([(F5x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([4,F5y-0.625,0])
cube([1,0.625,F5z]);
translate([5,F5y-0.5,0])
cube([1,0.5,F5z]);
translate([6,F5y-0.625,0])
cube([6.7,0.625,F5z]);
translate([12.7,F5y-0.5,0])
cube([1,0.5,F5z]);
translate([13.7,F5y-0.625,0])
cube([1,0.625,F5z]);
hull(){
translate([3.5,1.5,0])
cylinder(h = F5z, r = 0.5);
translate([4.5,1.5,0])
cylinder(h = F5z, r = 0.5);
}
} //end module
F6
some errors of symmetry in source dxf drawing. made some assumptions. need to check fit with interfacing parts.
Welds to: F2, F7
Bolts to: F9
F6x=22.1875; //?why not just 22?
F6y=8;
F6z=0.5;
$fn=20; //render final model at 100
projection(cut = true) //use projection to create 2D DXF files
difference(){
translate([-(F6x/2),0,0])
cube([F6x,F6y,F6z]);
translate([-(F6x/2),0,0])
cuts();
translate([(F6x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([1.26,F6y-0.5,0]) //?xdistance from center?
cube([1.125,0.5,F6z]); //?interfaces with what?
translate([(F6x/2)-1.125,F6y-3.22,0])
cube([2.25,3.22,F6z]);
translate([F6x/2,F6y-3.22,0])
cylinder(h = F6z, r = 1.125);
translate([(F6x/2)-8.5,2,0])
cylinder(h = F6z, r = 0.38); //diameter 0.76?
translate([(F6x/2)-8.5,6,0])
cylinder(h = F6z, r = 0.38);
} //end module
F8
Welds to: F9, F10
Bolts to: Rub Plate ?
F8x=43.5;
F8y=6;
F8z=0.5;
$fn=20; //render final model at 100
difference(){
cube([F8x,F8y,F8z]);
translate([-0.0625,0,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([14.5-0.0625,0,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([14.5+14.5-0.0625,0,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([-0.0625,F8y,0])
mirror([0,1,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([14.5-0.0625,F8y,0])
mirror([0,1,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
translate([14.5+14.5-0.0625,F8y,0])
mirror([0,1,0])
cornerjoint(7.375,0.625,0.25,0.5,0.125);
hull(){
translate([23.34,3,0]) //?x interfaces with what?
cylinder(h = F8z, r = 0.5);
translate([23.6,3,0])
cylinder(h = F8z, r = 0.5);
}
hull(){
translate([30.34,3,0]) //?x interfaces with what?
cylinder(h = F8z, r = 0.5);
translate([30.6,3,0])
cylinder(h = F8z, r = 0.5);
}
}
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,F8z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,F8z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,F8z]);
}
} //end cornerjoint module
F9
Welds to: F8, F11
Bolts to: F1, F4, F6
Abuts: A1 ?, A2 ?, F12
F9x=43.5;
F9y=4.5;
F9z=0.5;
$fn=20; //render final model at 100
difference(){
cube([F9x,F9y,F9z]);
translate([7.25,0,0])
cornerjoint(7.25,0.625,0.25,0.5,0.125);
translate([14.5+7.25,0,0])
cornerjoint(7.25,0.625,0.25,0.5,0.125);
translate([14.5+14.5+7.25,0,0])
cornerjoint(7.25,0.625,0.25,0.5,0.125);
translate([0,F9y-0.5625,0])
cube([0.53125,0.5625,F9z]);
translate([19.96875,F9y-0.5625,0])
cube([0.5625,0.5625,F9z]);
translate([31.3,F9y-1.4,0])
cube([6.4,1.4,F9z]); //?interfaces with what?
translate([F9x-0.5,F9y-0.5625,0])
cube([0.5,0.5625,F9z]);
translate([2,1.9,0]) //?x interfaces with what? ?1.9?
cylinder(h = F9z, r = 0.38);
translate([6,1.9,0]) //?x interfaces with what?
cylinder(h = F9z, r = 0.38);
translate([22.472,1.9,0]) //??.472?? ?interfaces with what?
cylinder(h = F9z, r = 0.5025);
translate([26.472,1.9,0])
cylinder(h = F9z, r = 0.5025);
translate([29.472,1.9,0])
cylinder(h = F9z, r = 0.5025);
translate([39,1.9,0]) //?x interfaces with what?
cylinder(h = F9z, r = 0.38);
translate([42,1.9,0]) //?x interfaces with what?
cylinder(h = F9z, r = 0.38);
}
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,F9z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,F9z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,F9z]);
}
} //end cornerjoint module
F10
Welds to: F8?
F10x=5.9; F10y=2; F10z=0.5; cube([F10x,F10y,F10y]);
F11
Welds to: F9
F11x=1.25;
F11y=6;
F11z=0.5;
projection(cut = true) //use projection to create 2D DXF files
difference(){
translate([0,-(F11y/2),0])
cube([F11x,F11y,F11z]);
translate([0,-(F11y/2),0])
cuts();
translate([0,(F11y/2),0])
mirror([0,1,0])
cuts();
} //end difference
module cuts(){
translate([0.5,0,0])
cube([0.125,0.625,F11z]);
translate([0.625,0,0])
cube([0.625,0.5,F11z]);
} //end module
Arms
A1
Welds to: A2, A6
Bolts to: A4, A5, F1, H7, H8
Abuts: F9
A1x=4;
A1y=72;
A1z=0.5;
$fn=20;
difference(){
cube([A1x,A1y,A1z]);
translate([0,0.71875,0])
cube([0.6875,0.5625,A1z]);
translate([0,44.8501,0]) //?y.8501?
cube([0.6875,0.5625,A1z]);
translate([0,70.9688,0]) //y 0.46875 from top
cube([0.6875,0.5625,A1z]);
translate([2,2,0])
cylinder(h = A1z, r = 0.4);
translate([2,4,0])
cylinder(h = A1z, r = 0.4);
translate([2,27,0])
cylinder(h = A1z, r = 0.4);
translate([2,37,0])
cylinder(h = A1z, r = 0.4);
hull(){
translate([2,39.67,0]) //small error on drawing
cylinder(h = A1z, r = 0.4);
translate([2,40.25,0]) //small error on drawing
cylinder(h = A1z, r = 0.4);
}
hull(){
translate([2,50.25,0]) //small error
cylinder(h = A1z, r = 0.4);
translate([2,50.85,0]) //small error
cylinder(h = A1z, r = 0.4);
}
translate([2,53.75,0])
cylinder(h = A1z, r = 0.4); translate([2,56.75,0])
cylinder(h = A1z, r = 0.4);
translate([2,63.75,0])
cylinder(h = A1z, r = 0.4);
translate([2,69,0])
cylinder(h = A1z, r = 0.4);
//corner joints
for(i=[0:5])
translate([4,i*11.9375,0])
rotate([0,0,90])
cornerjoint(6.0625,0.625,0.125,0.5,0.125);
}
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,A1z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,A1z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,A1z]);
}
} //end cornerjoint module
A2
Welds to: A1, A6
Bolts to: Guards, Hopper mounts
Abuts: F1 (?), F9
A2x=5.96603; //?just 6?
A2y=72;
A2z=0.5;
$fn=20;
difference(){
cube([A2x,A2y,A2z]);
translate([A2x-0.6875,0.46875,0])
cube([0.6875,0.5625,A2z]);
translate([A2x-0.6875,26.5874,0]) //?y.8501?
cube([0.6875,0.5625,A2z]);
translate([A2x-0.6875,A2y-0.71875,0]) //y 0.46875 from top
cube([0.6875,0.5625,A2z]);
hull(){
translate([A2x-1.75,21.2,0]) //?y?
cylinder(h = A2z, r = 0.4);
translate([A2x-1.75,22.765,0]) //?y?
cylinder(h = A2z, r = 0.4);
}
hull(){
translate([A2x-1.75,47.56,0]) //?y?
cylinder(h = A2z, r = 0.4);
translate([A2x-1.75,49.0785,0]) //?y?
cylinder(h = A2z, r = 0.4);
}
//corner joints
for(i=[0:5])
translate([0,(i*12)+6,0])
rotate([0,0,270])
cornerjoint(6,0.625,0.125,0.5,0.125);
}
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,A2z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,A2z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,A2z]);
}
} //end cornerjoint module
A3
Welds to: A4, A5
a3x=4;
a3y=72;
a3z=0.5;
$fn=20;
difference(){
cube([a3x,a3y,a3z]);
//corner joints
for(i=[0:5])
translate([0,(i*12)+6,0])
rotate([0,0,270])
cornerjoint(6,0.625,0.125,0.5,0.125);
}
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,a3z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,a3z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,a3z]);
}
} //end cornerjoint module
A4
Welds to: A3
Bolts to: A1
a4x=6;
a4y=72;
a4z=0.5;
$fn=20;
difference(){
cube([a4x,a4y,a4z]);
hull(){
translate([a4x-2,23.725,0]) //?y?
cylinder(h = a4z, r = 0.4);
translate([a4x-2,24.835,0]) //?y?
cylinder(h = a4z, r = 0.4);
}
hull(){
translate([a4x-4,23.725,0]) //?y?
cylinder(h = a4z, r = 0.4);
translate([a4x-4,24.835,0]) //?y?
cylinder(h = a4z, r = 0.4);
}
hull(){
translate([a4x-2,47.135,0])
cylinder(h = a4z, r = 0.4);
translate([a4x-2,48.265,0])
cylinder(h = a4z, r = 0.4);
}
hull(){
translate([a4x-4,47.135,0])
cylinder(h = a4z, r = 0.4);
translate([a4x-4,48.265,0])
cylinder(h = a4z, r = 0.4);
}
//corner joints
for(i=[0:5])
translate([0,(i*11.9375)+6.0625,0])
rotate([0,0,270])
cornerjoint(6.0625,0.625,0.125,0.5,0.125);
}
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,a4z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,a4z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,a4z]);
}
} //end cornerjoint module
A5
Welds to: A3
Bolts to: A1
a5x=6;
a5y=72;
a5z=0.5;
$fn=20;
difference(){
cube([a5x,a5y,a5z]);
hull(){
translate([3,23.795,0])
cylinder(h = a5z, r = 0.405);
translate([3,24.805,0])
cylinder(h = a5z, r = 0.405);
}
hull(){
translate([3,47.2,0])
cylinder(h = a5z, r = 0.405);
translate([3,48.2,0])
cylinder(h = a5z, r = 0.405);
}
//corner joints
for(i=[0:5])
translate([6,(i*12)+5.9375,0])
rotate([0,0,90])
cornerjoint(6.125,0.625,0.125,0.5,0.125);
}
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,a5z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,a5z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,a5z]);
}
} //end cornerjoint module
A6
Welds to: A1, A2
Drawer
D1
d1x=18.5;
d1y=18;
d1z=0.5;
$fn=20;
difference(){
translate([-(d1x/2),0,0])
cube([d1x,d1y,d1z]);
translate([-(d1x/2),0,0])
cuts();
translate([(d1x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
cube([2.5,16,d1z]);
translate([2.5,1.5,0])
cube([0.6,5,d1z]);
} //end module
D2
d2x=18.5;
d2y=6;
d2z=0.5;
$fn=20;
difference(){
cube([d2x,d2y,d2z]);
//1 cuts numbered clockwise from top left
translate([0,d2y-0.43,0])
cube([2,0.43,d2z]);
//2
translate([5.25,d2y,0])
insert(0.8125,1.3125,0.125,0.3125,0.125,0.8125);
//3
translate([11.75,d2y,0])
insert(0.8125,2.8125,0.125,0.3125,0.125,2.0625);
translate([11.75+0.28125,d2y-0.53125,0])
cube([1,0.53125,d2z]);
translate([11.75+0.78125,d2y-0.65625,0])
cube([0.625,0.25,d2z]);
//4
translate([d2x,d2y,0])
insert(1.3125,2.8125,0.125,0.8125,0.125,1.8125);
//5
translate([d2x,0,0])
insert(1.3125,1.8125,0.125,0.8125,0.125,1.3125);
translate([d2x,0,0])
insert(2.375,1.3125,0.125,1.875,0.125,0.8125);
//6 ??? error ???
translate([11.4688,0,0])
cube([0.546875,0.78125,d2z]);
translate([11.4688+0.546875,0,0])
cube([0.640575,0.53125,d2z]);
translate([11.3438,0.40625,0])
cube([0.25,0.5,d2z]);
translate([11.885609,0.65625,0])
cube([0.255066,0.25,d2z]);
translate([11.4688+0.546875+0.640575-.125,0.28125,0])
cube([0.25,0.375,d2z]);
//X values in dxf dont seem standard? error in model?
//translate([11.75,0,0]) //insert(0.8125,1.8125,0.125,0.3125,0.125,1.3125);
//translate([11.75,0,0]) //insert(0.8125,1.8125,0.125,0.3125,0.125,1.3125);
//7
translate([4.65625,0,0])
insert(1.125,1.3125,0.125,0.625,0.125,0.8125);
translate([5.25,0,0])
insert(0.8125,2.3125,0.125,0.3125,0.125,1.8125);
translate([5.25,0.53125,0])
cube([0.40625,0.375,d2z]);
//8
insert(1.8125,1.3125,0.125,1.3125,0.125,0.8125);
} //end difference
module insert(X,Y,standdepthX,standwidthX,standdepthY,standwidthY){
difference(){
translate([0,0,d2z/2]){
#cube([X,Y,d2z],true);
}
translate([X/2,0,d2z/2]){
cube([standdepthY*2,standwidthY,d2z],true);
}
translate([-X/2,0,d2z/2]){
cube([standdepthY*2,standwidthY,d2z],true);
}
translate([0,Y/2,d2z/2]){
cube([standwidthX,standdepthX*2,d2z],true);
}
translate([0,-Y/2,d2z/2]){
cube([standwidthX,standdepthX*2,d2z],true);
}
}
} //end insert
D3
d3x=13;
d3y=5.5;
d3z=0.5;
$fn=20;
difference(){
translate([-(d3x/2),0,0])
cube([d3x,d3y,d3z]);
translate([-(d3x/2),0,0])
cuts();
translate([(d3x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([0,0.75,0])
cube([0.5,4,d3z]);
translate([0.5,0.75,0])
cube([0.125,0.125,d3z]);
translate([0.5,1.125,0])
cube([0.125,3.25,d3z]);
translate([0.5,4.625,0])
cube([0.125,0.125,d3z]);
translate([3.5,4.625,0])
insert(0.75,1,0.09375,0.25);
translate([3.5,2.5,0])
insert(0.75,0.75,0.09375,0.25);
translate([3.5,0.125,0])
insert(0.75,1.5,0.09375,0.25);
translate([d3x/2,4.625,0])
insert(0.75,1,0.09375,0.25);
translate([d3x/2,2.5,0])
insert(0.75,0.75,0.09375,0.25);
translate([d3x/2,0.125,0])
insert(0.75,1.5,0.09375,0.25);
} //end module
module insert(X,Y,standdepth,standwidth){
difference(){
translate([0,0,d3z/2]){
#cube([X,Y,d3z],true);
}
translate([X/2,0,d3z/2]){
cube([standdepth*2,standwidth,d3z],true);
}
translate([-X/2,0,d3z/2]){
cube([standdepth*2,standwidth,d3z],true);
}
translate([0,Y/2,d3z/2]){
cube([standwidth,standdepth*2,d3z],true);
}
translate([0,-Y/2,d3z/2]){
cube([standwidth,standdepth*2,d3z],true);
}
}
} //end insert
D4
d4x=7;
d4y=5.5;
d4z=0.5;
$fn=20;
difference(){
translate([-(d4x/2),0,0])
cube([d4x,d4y,d4z]);
translate([-(d4x/2),0,0])
cuts();
translate([(d4x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([0,d4y-0.75,0])
rotate([0,0,270])
cornerjoint(1.46875,0.625,0.125,1.21875,0.125);
translate([0,1.46875+1.25,0])
rotate([0,0,270])
cornerjoint(1.46875,0.625,0.125,1.21875,0.125);
translate([-0.125,0,0])
cornerjoint(3.375,0.625,0.125,3.125,0.125);
} //end module
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,d4z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,d4z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,d4z]);
}
} //end cornerjoint module
D5
d5x=13;
d5y=6;
d5z=0.5;
$fn=20;
difference(){
translate([-(d5x/2),0,0])
cube([d5x,d5y,d5z]);
translate([-(d5x/2),0,0])
cuts();
translate([(d5x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([0,0.5,0])
cube([0.5,5,d5z]);
translate([0.5,0.5,0])
cube([0.125,0.125,d5z]);
translate([0.5,0.875,0])
cube([0.125,4.25,d5z]);
translate([0.5,5.375,0])
cube([0.125,0.125,d5z]);
translate([1,0,0])
cube([5,0.125,d5z]);
translate([1,d5y-0.125,0])
cube([5,0.125,d5z]);
translate([3.5,3,0])
insert(0.75,0.75,0.09375,0.25);
translate([d5x/2,3,0])
insert(0.75,0.75,0.09375,0.25);
} //end module
module insert(X,Y,standdepth,standwidth){
difference(){
translate([0,0,d5z/2]){
#cube([X,Y,d5z],true);
}
translate([X/2,0,d5z/2]){
cube([standdepth*2,standwidth,d5z],true);
}
translate([-X/2,0,d5z/2]){
cube([standdepth*2,standwidth,d5z],true);
}
translate([0,Y/2,d5z/2]){
cube([standwidth,standdepth*2,d5z],true);
}
translate([0,-Y/2,d5z/2]){
cube([standwidth,standdepth*2,d5z],true);
}
}
} //end insert
D6
d6x=13;
d6y=6;
d6z=0.5;
$fn=20;
difference(){
translate([-(d6x/2),0,0])
cube([d6x,d6y,d6z]);
translate([-(d6x/2),0,0])
cuts();
translate([(d6x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([0,5.5,0])
rotate([0,0,270])
cornerjoint(4.5,0.625,0.125,0.25,0.125);
translate([5,2,0])
insert(0.75,0.75,0.09375,0.25);
} //end module
module insert(X,Y,standdepth,standwidth){
difference(){
translate([0,0,d6z/2]){
#cube([X,Y,d6z],true);
}
translate([X/2,0,d6z/2]){
cube([standdepth*2,standwidth,d6z],true);
}
translate([-X/2,0,d6z/2]){
cube([standdepth*2,standwidth,d6z],true);
}
translate([0,Y/2,d6z/2]){
cube([standwidth,standdepth*2,d6z],true);
}
translate([0,-Y/2,d6z/2]){
cube([standwidth,standdepth*2,d6z],true);
}
}
} //end insert
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,a4z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,a4z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,a4z]);
}
} //end cornerjoint module
D7
d7x=3;
d7y=3;
d7z=0.5;
$fn=20;
difference(){
cube([d7x,d7y,d7z]);
translate([d7x/2,d7y/2,0])
cylinder(h = d7z,r = 0.5);
}
D8
d8x=13;
d8y=5;
d8z=0.5;
$fn=20;
difference(){
translate([-(d8x/2),0,0])
cube([d8x,d8y,d8z]);
translate([-(d8x/2),0,0])
cuts();
translate([(d8x/2),0,0])
mirror([1,0,0])
cuts();
} //end difference
module cuts(){
translate([0,4.25,0])
rotate([0,0,270])
cornerjoint(3.5,0.625,0.125,0.25,0.125);
translate([1,d8y-0.125,0])
cube([5.125,0.125,d8z]);
translate([5,3.5,0])
insert(0.75,0.75,0.09375,0.25);
} //end module
module insert(X,Y,standdepth,standwidth){
difference(){
translate([0,0,d8z/2]){
#cube([X,Y,d8z],true);
}
translate([X/2,0,d8z/2]){
cube([standdepth*2,standwidth,d8z],true);
}
translate([-X/2,0,d8z/2]){
cube([standdepth*2,standwidth,d8z],true);
}
translate([0,Y/2,d8z/2]){
cube([standwidth,standdepth*2,d8z],true);
}
translate([0,-Y/2,d8z/2]){
cube([standwidth,standdepth*2,d8z],true);
}
}
} //end insert
module cornerjoint(L,H,EndGap,PadL,PadH){
difference(){
cube([L,H,a4z]);
translate([EndGap,H-PadH,0])
cube([PadL,PadH,a4z]);
translate([L-EndGap-PadL,H-PadH,0])
cube([PadL,PadH,a4z]);
}
} //end cornerjoint module
D9
d9x=3.5;
d9y=3.5;
d9z=0.5;
$fn=20;
difference(){
cube([d9x,d9y,d9z]);
translate([2,0,0])
singlepeg(0.5,0.5,0.125,0.125,d9x);
translate([-0.0000001,2,0]) //slight x shift to fix abberation
rotate([0,0,270])
singlepeg(0.5,0.5,0.125,0.125,d9x);
translate([2,2,0])
cylinder(h = d9z,r = 0.5);
} //end difference
module singlepeg(L,W,divotsDepth,divotsW,sidelength){
translate([(W/2),0,0]){
union(){
cube([divotsW,L+divotsDepth,d9z]);
translate([divotsW,0,0])
cube([sidelength,L,d9z]);
}
}
translate([-(W/2),0,0]){
mirror([1,0,0]){
union(){
cube([divotsW,L+divotsDepth,d9z]);
translate([divotsW,0,0])
cube([sidelength,L,d9z]);
}
}
}
}
D10
d10x=18;
d10y=3;
d10z=0.5;
$fn=20;
difference(){
cube([d10x,d10y,d10z]);
translate([1,d10y/2,0])
cylinder(h = d10z,r = 0.55);
translate([4,d10y/2,0])
cylinder(h = d10z,r = 0.55);
translate([9,d10y/2,0])
cylinder(h = d10z,r = 0.55);
translate([14,d10y/2,0])
cylinder(h = d10z,r = 0.55);
translate([17,d10y/2,0])
cylinder(h = d10z,r = 0.55);
} //end difference
Grate
G1
g1x=23;
g1y=2;
g1z=0.5;
$fn=20;
difference(){
cube([g1x,g1y,g1z]);
translate([7,g1y/2,0])
cylinder(h = g1z,r = 0.4065);
translate([16,g1y/2,0])
cylinder(h = g1z,r = 0.4065);
} //end difference
G2
g2x=56;
g2y=2.3;
g2z=0.5;
$fn=20;
union(){
difference(){
cube([g2x,g2y-0.1,g2z]);
translate([4.375,1.6,0]) //goofy distance apart holes
cylinder(h = g2z,r = 0.406);
translate([20.125,1.6,0])
cylinder(h = g2z,r = 0.406);
translate([35.875,1.6,0])
cylinder(h = g2z,r = 0.406);
translate([51.625,1.6,0])
cylinder(h = g2z,r = 0.406);
//first two cuts are goofy distance from begining, so is last one.
for(i=[0:((g2x-3.4)/1.75)])
translate([(i*1.75)+3.4,0,0])
cube([0.3,0.5,g2z]);
translate([1.6,0,0])
cube([0.3,0.5,g2z]);
} //end difference
//goofy distance from end
translate([15.9475,g2y-0.1,0])
cube([0.3,0.1,g2z]);
translate([g2x-15.9475-0.3,g2y-0.1,0])
cube([0.3,0.1,g2z]);
}
G3
g3x=2;
g3y=3;
g3z=0.5;
$fn=20;
difference(){
cube([g3x,g3y,g3z]);
translate([1,1,0])
cylinder(h = g3z,r = 0.40625);
} //end difference
G4
g4x=5;
g4y=2.5;
g4z=0.5;
$fn=20;
difference(){
cube([g4x,g4y,g4z]);
translate([1,1.25,0])
cylinder(h = g4z,r = 0.40625);
} //end difference