Talk:MicroTrac Controller v17.10: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
 
(18 intermediate revisions by the same user not shown)
Line 5: Line 5:
*Arduino MKR WAN 1300 [https://store.arduino.cc/usa/mkr-wan-1300 link]
*Arduino MKR WAN 1300 [https://store.arduino.cc/usa/mkr-wan-1300 link]
**new board for arduino, comes out in november
**new board for arduino, comes out in november
=Latency=
some digi cards have reported latency issues. might need to change xbee card.
*https://www.digi.com/support/forum/5998/can-get-predictable-consistent-latency-using-xbee-pro-module
*https://www.digi.com/support/forum/7695/variable-latency-and-hanging-on-of-xbee-pro-2
*https://www.digi.com/support/forum/3033/xbee-s2-zigbee-latency-problem
**"I would try with routers and sending a unicast to each of them instead of a broadcast. Also, maybe ZigBee is not the best option here if speed is relevant (ZigBee migth add up to seconds due to Mesh network routing), XBee Series 1 (802.15.4) are faster than ZigBee and the configuration is similar if you want to deploy a star network."
*might try using GPIO pins on xbee radio to avoid using serial communication
**need to use 330 ohm resistor + 3.3V zener diode to drop from 5V to 3.3V for each pin


=Remote Control Arduino Examples=
=Remote Control Arduino Examples=
Line 10: Line 22:
*http://www.instructables.com/id/Control-the-relays-via-GPRS-SMS/
*http://www.instructables.com/id/Control-the-relays-via-GPRS-SMS/
*http://www.instructables.com/id/Arduino-Wireless-Serial-Communication/
*http://www.instructables.com/id/Arduino-Wireless-Serial-Communication/
===Xbee Examples===
*http://www.ardumotive.com/how-to-use-xbee-modules-as-transmitter--receiver-en.html


=Control=
=Control=
Line 31: Line 48:
*trottle potentiometer - linear actuator?
*trottle potentiometer - linear actuator?


==Actuators==
===Actuators===


*https://www.servocity.com/100-mm-stroke-4-lb-thrust-light-duty-linear-servo
*https://www.servocity.com/100-mm-stroke-4-lb-thrust-light-duty-linear-servo
*https://www.hobbyzone.com/radio-related/servo-related/servos/linear/SPMSH2040T.html


=switches=
===Input Devices and Switches===


*joysticks
*joysticks
**https://www.sparkfun.com/products/9426
**https://www.sparkfun.com/products/9426
**https://www.sparkfun.com/products/9032
*switches
**https://www.grainger.com/product/HONEYWELL-Toggle-Switch-24D449
***https://www.grainger.com/product/APM-HEXSEAL-Toggle-Switch-Boot-1UDJ7
===Relay Boards===
[[Relay Module]]
*https://smile.amazon.com/SainSmart-101-70-102-8-Channel-Relay-Module/dp/B0057OC5WK/
== Wire Connections ==
===Trailer Connections===
*4-way Knockout mounted connector [https://www.grainger.com/product/REESE-Flat-Knock-Out-Wiring-Kit-20PR31 grainger]
**these would look nice on a box. no dimensions listed online. hole size?
==Radio Coax Cable Connections==
see https://en.wikipedia.org/wiki/SMA_connector#Reverse_polarity
== wire routing ==
*putting two 18 gauge wires into one relay module terminal block is tricky.
**could have switch wire and trailer plug wire meet at a crimp connector then have one wire go to relay module
== GPS Module ==
http://www.doctormonk.com/2012/05/sparkfun-venus-gps-and-arduino.html
Three pins on GPS module GRND, 3.3V, TX
== Compass and Logic Level Converter ==
https://learn.sparkfun.com/tutorials/hmc6343-3-axis-compass-hookup-guide
need a converter to communicate between 3.3v compass and 5v arduino pins
https://learn.sparkfun.com/tutorials/bi-directional-logic-level-converter-hookup-guide
== USB on/off switch ==
how to splice in an on/off switch to a usb cable
*http://www.instructables.com/id/OnOff-switch-for-a-USB-Powered-Device/

Latest revision as of 07:28, 10 June 2018

Wireless Communication Options

  • Arduino's official wifi shield is discontinued
  • Could use xbee radio w/ shield
  • Arduino MKR WAN 1300 link
    • new board for arduino, comes out in november

Latency

some digi cards have reported latency issues. might need to change xbee card.

  • might try using GPIO pins on xbee radio to avoid using serial communication
    • need to use 330 ohm resistor + 3.3V zener diode to drop from 5V to 3.3V for each pin

Remote Control Arduino Examples

Xbee Examples


Control

  • Relay Board Controlled
    • left side forward
    • left side reverse
    • right side forward
    • right side reverse
    • main arm up
    • main arm down
    • bucket up
    • bucket down
    • engine start
    • engine kill
    • auxillary
    • auxillary
  • choke - linear actuator?
  • trottle potentiometer - linear actuator?

Actuators

Input Devices and Switches

Relay Boards

Relay Module

Wire Connections

Trailer Connections

  • 4-way Knockout mounted connector grainger
    • these would look nice on a box. no dimensions listed online. hole size?

Radio Coax Cable Connections

see https://en.wikipedia.org/wiki/SMA_connector#Reverse_polarity

wire routing

  • putting two 18 gauge wires into one relay module terminal block is tricky.
    • could have switch wire and trailer plug wire meet at a crimp connector then have one wire go to relay module

GPS Module

http://www.doctormonk.com/2012/05/sparkfun-venus-gps-and-arduino.html

Three pins on GPS module GRND, 3.3V, TX

Compass and Logic Level Converter

https://learn.sparkfun.com/tutorials/hmc6343-3-axis-compass-hookup-guide

need a converter to communicate between 3.3v compass and 5v arduino pins

https://learn.sparkfun.com/tutorials/bi-directional-logic-level-converter-hookup-guide

USB on/off switch

how to splice in an on/off switch to a usb cable

Retrieved from "https://wiki.opensourceecology.org/index.php?title=Talk:MicroTrac_Controller_v17.10&oldid=173398"