120V Heatbed: Difference between revisions
Jump to navigation
Jump to search
(→About) |
|||
| Line 54: | Line 54: | ||
*Here is another at 12V, with 16 gauge - 10' long, going up only to 225C. [http://forum.seemecnc.com/viewtopic.php?t=13] | *Here is another at 12V, with 16 gauge - 10' long, going up only to 225C. [http://forum.seemecnc.com/viewtopic.php?t=13] | ||
[[File:nichromeheater2.jpg]]. | [[File:nichromeheater2.jpg]]. | ||
==Derivative for OSE + Calculations== | |||
*31 ga, 19 feet long above | |||
*Power to bring 31 ga up to 2000F is under 4A - so with full 500W, 31 ga wire would probably blow up. [https://wiretron.com/nichrome-resistance-wires/]. Need to go thicker to handle the power. | |||
*See Electronics Stack Exchange - [https://electronics.stackexchange.com/questions/20542/can-i-using-nichrome-wire-to-light-a-candle-electronicaly] | |||
=Links= | =Links= | ||
*Hackaday article - [https://hackaday.io/project/8671-110-230-v-pcb-heated-bed] | *Hackaday article - [https://hackaday.io/project/8671-110-230-v-pcb-heated-bed] | ||
Revision as of 01:34, 27 April 2019
About
- OSE Reasons for using a nichrome 120V bed are scalability and lower cost for large beds.
- Reason for DIY nichrome beds is clear for larger beds on the basis of cost.
- Sound design is required a safe method:
- Do not use parts that melt at low temperature. Thus, use Nichrome C wire and braided fiberglass insulation.
- For connection, use high temp 200C wire, and simply wind them around each other. But wait... How to Connect Wire to Nichrome Heaters.
Sourcing
Pad
- 400+ watt 8" beds do not exist - [1]. It is questionable whether this one has 500W on 120V - [2]. Closest is the Ultimaker clone - [3]
- 8" bed on amazon is $84. [4]
- 8" bed on Aliexpress is $45 - [5]
- Expensive 12" on amazon - [6]
- Silicone rubber sheet - to 450F - [7] - $6/sf
- 10x10" heatbed aliexpress 500W - $10 - [8]
- 200W 8x8, $13 - [9]
Silicone Rubber Sheet
Double Sided Tape
- $3/sf - [12]
Single Sided Tape
- Kapton tape, 4"x100ft - $25 - [13]
- Enough for 300 small beds (4"), or 33 12" beds.
Coated Nichrome Wire
- Need 30 Ohms of wire, about 10' long
- See Nichrome Wire
Uncoated Nichrome Wire
- Need 30 Ohm resistance for the length of wire at 120V to get 480W, for P=IV, V=IR, I=V/R -> P=V^2/R = 120^2/30 according to Electrical Power Calculator.
High Temp Nichrome in Fiberglass
- Claim of 1200C - [14]
Sleeving
Rope Heater
- Up to 500C - [17]. Description: helical winding around core material, then insulating sleeve.
Helical Nichrome Coil
- Can be stretched - [18]
Carbon Fiber
- Carbon fiber is also used as a heating wire - [19]. Interesting. But it appears it can only do 15W/meter? Why is it limited? Limitation appears to be encapsulating materials - [20]
Example of a DIY Nichrome Heater
- Idea is to wind Nichrome around an inner core, as otherwise, the heater element gets too long. That is just a practical consideration for these types of heaters if running high voltage.
- Here is 31 ga and 19 feet - for 90W - at 115V. [21]
- Here is another at 12V, with 16 gauge - 10' long, going up only to 225C. [22]
.
Derivative for OSE + Calculations
- 31 ga, 19 feet long above
- Power to bring 31 ga up to 2000F is under 4A - so with full 500W, 31 ga wire would probably blow up. [23]. Need to go thicker to handle the power.
- See Electronics Stack Exchange - [24]
Links
- Hackaday article - [25]