120V Heatbed: Difference between revisions
Jump to navigation
Jump to search
(→About) |
(→About) |
||
| Line 7: | Line 7: | ||
*Metal, glass, ceramic have been used successfully as heated beds. | *Metal, glass, ceramic have been used successfully as heated beds. | ||
:*Ceramic - [https://hackaday.io/project/20848-arcus-3d-m2-ceramic-heated-bed] | :*Ceramic - [https://hackaday.io/project/20848-arcus-3d-m2-ceramic-heated-bed] | ||
:*'''Granite success and looks good''' -[https://groups.google.com/forum/#!msg/solidoodle/oeg854r2nAc/wnlYSx9YyckJ] | |||
:*'''Ceramic Floor Tile with Pictures''' - [https://groups.google.com/forum/#!topic/cubex-3d-printing/-O230cSgGVI]. Addresses the melting of edges - edges remain cool. | |||
=Sourcing= | =Sourcing= | ||
Revision as of 01:05, 28 April 2019
About
- OSE Reasons for using a nichrome 120V bed are scalability and lower cost for large beds.
- Reason for DIY nichrome beds is clear for larger beds on the basis of cost.
- Sound design is required a safe method:
- Do not use parts that melt at low temperature. Thus, use Nichrome C wire and braided fiberglass insulation.
- For connection, use high temp 200C wire, and simply wind them around each other. But wait... How to Connect Wire to Nichrome Heaters.
- Metal, glass, ceramic have been used successfully as heated beds.
Sourcing
Bed Plate
Aluminum
- All with hefty shipping - 6" $3- [4], 12" $20 with ship for 1 [5], 8x16 $24 [6], 8x8 $13 [7] -
- 24" $43 [8]. $10 per 12" bed, or $5 per 8" bed
- McMaster stock - $13 + SH for 8" - [9]
Steel
- This would be interesting to CNC torch on a waterbed from 8" stock - or just cut with abrasive metal cutoff. Steel is under $1/lb - with a 1 square foot sheet weighing $5. So $5 is the baseline cost for 12" beds.
- If steel is torched, this should be done with water cooling to address warping
- Baseline cost is $5 vs. $10 for aluminum.
Tile
- Tile is a winner in terms of cost at $1/sf. 77 cents [10].
- Granite - $2.50 - [11]
- Polished ceramic tile 69 cents - [12]
Pad
- Ultimaker beds are 500W - - [13]
- 8" bed on amazon is $84. [14]
- 8" bed on Aliexpress is $45 - [15]
- Expensive 12" on amazon - [16]
- Silicone rubber sheet - to 450F - [17] - $6/sf
- 10x10" heatbed aliexpress 500W - $10 - [18]
- 200W 8x8, $13 - [19]
Silicone Rubber Sheet
Double Sided Tape
- $3/sf - [22]
Single Sided Tape
- Kapton tape, 4"x100ft - $25 - [23]
- Enough for 300 small beds (4"), or 33 12" beds.
Coated Nichrome Wire
- Need 30 Ohms of wire, about 10' long
- See Nichrome Wire
Uncoated Nichrome Wire
- Need 30 Ohm resistance for the length of wire at 120V to get 480W, for P=IV, V=IR, I=V/R -> P=V^2/R = 120^2/30 according to Electrical Power Calculator.
High Temp Nichrome in Fiberglass
- Claim of 1200C - [24]
Sleeving
Rope Heater
- Up to 500C - [27]. Description: helical winding around core material, then insulating sleeve.
Helical Nichrome Coil
- Can be stretched - [28]
Carbon Fiber
- Carbon fiber is also used as a heating wire - [29]. Interesting. But it appears it can only do 15W/meter? Why is it limited? Limitation appears to be encapsulating materials - [30]
Example of a DIY Nichrome Heater
- Idea is to wind Nichrome around an inner core, as otherwise, the heater element gets too long. That is just a practical consideration for these types of heaters if running high voltage.
- Here is 31 ga and 19 feet - for 90W - at 115V. [31]
- Here is another at 12V, with 16 gauge - 10' long, going up only to 225C. [32]
.
Derivative for OSE + Calculations
- 31 ga, 19 feet long above
- Power to bring 31 ga up to 2000F is under 4A - so with full 500W, 31 ga wire would probably blow up. [33]. Need to go thicker to handle the power.
- See Electronics Stack Exchange - [34]
Links
- Insulated Heatbed
- Hackaday article - [35]