April 2011 Production Run Hydraulics BOM

Generator

1. [1] hydraulic motor for direct 1800RPM generator drive - [1]
2. [1] 5/8" coupler - [2]

Other

1. [1] Power Cube Throttle Cable - [3] - need 5
2. Battery Cable - [4] - need 3
3. Starter Solenoid - [5] - need 5
4. Key Switch - [6] - need 5
5. Fuel Hose Barb - [7] - need 5

Tractor (x3)

See Parts Sourcing for contact information. Note: this includes hydraulics and balance of system after metal.

1. [8] 1-7/8" Flange Bearings - [8] ; plus BearingsOn plus Big Bearing Store
2. [2] Front Loader cylinders - 36" - $174 - 48 5/8" retracted length - [9] & [2] of [[10]]
3. [2] QA Plate Cylinders - [11]
4. [4] 3/8 NPTM x 1/2 NPTF swivel [12] for QA Plate cylinders
5. [4] 3/8 NPTM x 1/2 NPTF 90 swivel [13] for Loader cylinders
6. [4] Motors - [14]
   1. [8] SAE M 10 to NPT M 1/2" for Ports [15]
   2. [4] SAE 4M TO 1/4" NPTM CONNECTOR for Case Drains [16]
   3. [8] 1/2" QC for Motors [17]
   4. [4] 1/4" QC for motors [18]
7. [2] 1-1/4 SHAFT COUPLER W 5/16" KEYWAY - [19]
8. [1 1/3] 1-3/8" 6T fully splined shafting - [20]
9. [2] Female 1-3/8" 6T spline coupling - [21], $17 each
10. [12] 1.875" double split shaft collars - [22]
11. Double split - $11 - [23]
12. Double split - $9 -Houston Bearing
13. Double split - $9 free ship - [24]
14. Single split - [25]

Motor Valves

• [1] 3-spool motor valve, 25 gpm - [26], $288
• [2] 3/4" Nips [27] (includes cylinder valve)
• [1] 3/4" swivel - [28]
• [2] 3/4" Quick Couplers for one set of motor valve work ports - Dalton Hydraulics
• [4] 1/2" Swivels for work ports [29] - for 2 sets of work ports to wheel motors
• [1] 3/4" tee for inlet - [30]
• [1] 3/4" elbow for inlet - [31]
• [2] 30 GPM check valves for inlet - [32]
• [2] 3/4" QC for inlet - Dalton
• [5] 3/4"nips for inlet including valve in/out - [33]
• [2] 1/2 NPT hex nipples [34]-for auxiliary pair of motor valve work ports
• [2] 3/4 NPT to 1/2 NPT bushing [35] - auxiliary work ports - NA

Loader Valve

• [1] Prince 2 Spool Valve - [36] $189
• [1] 3/4" NPT nip for outlet - [37]
• [4] 1/2" Swivels for work ports [38] - for 2 sets of work ports to wheel motors
• [1] 3/4" QC for outlet
• [2] 1/2" tees to split to 2 cylinders

Cushion Valve

• [1] 1/2 NPT 30 GPM 1500-3000 PSI HYD CUSHION VALVES - [39]
• [6] 1/2" swivels [40] - 4 valve outlet + 2 cushion valve
• [2] 1/2" nip - [41] - going from between swivel and tee
• [4] NPTF Tee [42]- (includes QA plates

Power Cube

• [1] Pump - 0.98 cu in - [43]
• [1] 3/4" coupler for exit - Dalton
• [1] 3/4" breather cap -[44] - $13
• [1] Filler Cap - [45]
• [1] SAE 12 in to 3/4 hosebarb- [46]
• [1] SAE 10 out to 1/2 NPT - [47]
• [1] 3/4 to 1/2 reducer bushing - NA
• [1] Coupler half, 5/8" - $10
• [1] Coupler half, 1 1/8" - $10
• [1] Solid spider - $14
• [1] Suction strainer, 2" to 1-1/4" - [48] - $23
• [1] Pressure relief for power cube bypass- [49]
• [1] 20 GPM return Line Filter - [50] - 3 of these
• 1" female coupling into frame
• [1] 1" nip to filter - [51]
• [1] 30 GPM return Line Filter - [52] - 3 total of these
• [1] 1"-3/4" reducer bushing - [53]
• [1] 3/4" tee - [54]
• [2] 3/4" nip - [55]
• [1] 30 gpm Quick Coupler to return line
• [1] 3/4"-1/4" NPT reducer bushing for case drain - [56]
• [1] 1/4" nip - [57]
• [1] 1/4" quick couplers for case drain - [58]

Soil Pulverizer

• [1] 7.6 cu in hydraulic PTO motor - [59]
• [2] 10' hose - [60] $21
• [2] 1-7/8" bearings - []
• 6 tooth spline coupler - [61] (enough for 3)

Hoses

Power Cube

• [2] 10 foot hoses - [62]

Motor Valves

• [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of the valves [63]
• [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of front motors [64]
• [4] 1/2 X 1/2 X 1/2 NPTF TEE [65]
• [4] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for rear motors [66]

Motor Case Drains

• [2] 1/4" X 60" NPTM 2750 PSI HYD HOSE to run parallel with tractor sides [67]
• [1] 1/4" X 72" hose return to Power Cube [68]
• [1] 1/4" X 36" NPTM 2750 PSI HYD HOSE to Rear Motors [69]
• [3] 1/4 X 1/4 X 1/4 NPTF TEE [70]
• [3] 1/4 NPT hex nipples [71]

Front Loader

• [2] 1/2" X 12" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE from Valves to Cushion [72]
• [2] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for left front loader cylinder [73]
• [1] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [74]
• [1] 1/2" X 60" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [75]

QA Cylinder

• [2] 1/2" nips - going from cylinder swivels to tees - [76]
• [2] 1/2" NPTF tees - from cylinder to hoses - [77]
• [2] 1/2" X 48" NPTM 3000 PSI HYD HOSE [78]
• [1] 1/2" X 120" NPTM 3000 PSI HYD HOSE [79]
• [1] 1/2" X 144" NPTM 3000 PSI HYD HOSE [80]