Shop Prep Checklist: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Overall= | |||
*Food acquisition | |||
*Safety glasses | |||
*Clean off 2 more welding tables | |||
*Remove 3D printer | |||
*Lay out all materials on 8 welding stations tables | |||
*Set up 2 more torches | |||
*Pick up Sweiger metal | |||
:*1/4"x4" flats - 20' | |||
:*1/4"x2 flats - 60' | |||
:*4 insulators for Tweco guns | |||
:*Bottles exchange; 2 more new acetylene and 1 more new oxygen bottles | |||
:*4'x8' sheet steel of 1/4" metal | |||
:*2 spools of welding wire | |||
:*2.5"x4" DOM, 2.5" long, for 2.5" shaft fitting inside | |||
:*thread tape - 2 small rolls | |||
*Last minute shopping: 4 cans of black spray paint | |||
*7/16" bolts for engine | |||
*Move 2 power cube PC to make it more visible | |||
*Hose adapter - 1/2" to 3/4" | |||
*SeWire up manual valve | |||
*Print out instructionals | |||
*Provide control code specification | |||
*Finish masks verification | |||
*Weld cylinder? | |||
=Welding= | =Welding= | ||
#Test all welders according to [[Welders Check Protocol]]. Replace liner if needed. Inventory spools, tips, | #Test all welders according to [[Welders Check Protocol]]. Replace liner if needed. Inventory spools, tips, | ||
#Clean spools of welding wire | |||
#Welding masks - check if they darken; put broken ones back on shelves, mark them as broken. Check lens covers, replace as needed. Clear visibility but dark should be the norm. If can't see clearly, need to replace. | #Welding masks - check if they darken; put broken ones back on shelves, mark them as broken. Check lens covers, replace as needed. Clear visibility but dark should be the norm. If can't see clearly, need to replace. | ||
#Organize drills and charging stations | #Organize drills and charging stations | ||
#Dismantle brick press | #[[File:check.png]]Dismantle brick press | ||
#Buff CEB press metal | #Buff CEB press metal | ||
#Paint CEB press metal | #Paint CEB press metal | ||
#Inventory grinders | #Inventory grinders | ||
#Inventory bolts | #Inventory bolts | ||
#Get 2 more acetylene bottles and 1 oxygen | #Get[[File:check.png]] 2 more acetylene bottles and 1 oxygen | ||
#Get last materials - battry, press foot, pin, as by CAD | #Get last materials - battry, press foot, pin, as by CAD | ||
#'''Cut and weld cylinder''' | #'''Cut and weld cylinder''' | ||
| Line 18: | Line 45: | ||
#Cut 7" rebar reinforcements | #Cut 7" rebar reinforcements | ||
#Bring hoist over | #Bring hoist over | ||
#Fire up tractor | #[[File:check.png]]Fire up tractor | ||
=Torching= | =Torching= | ||
Latest revision as of 18:40, 24 August 2017
Overall
- Food acquisition
- Safety glasses
- Clean off 2 more welding tables
- Remove 3D printer
- Lay out all materials on 8 welding stations tables
- Set up 2 more torches
- Pick up Sweiger metal
- 1/4"x4" flats - 20'
- 1/4"x2 flats - 60'
- 4 insulators for Tweco guns
- Bottles exchange; 2 more new acetylene and 1 more new oxygen bottles
- 4'x8' sheet steel of 1/4" metal
- 2 spools of welding wire
- 2.5"x4" DOM, 2.5" long, for 2.5" shaft fitting inside
- thread tape - 2 small rolls
- Last minute shopping: 4 cans of black spray paint
- 7/16" bolts for engine
- Move 2 power cube PC to make it more visible
- Hose adapter - 1/2" to 3/4"
- SeWire up manual valve
- Print out instructionals
- Provide control code specification
- Finish masks verification
- Weld cylinder?
Welding
- Test all welders according to Welders Check Protocol. Replace liner if needed. Inventory spools, tips,
- Clean spools of welding wire
- Welding masks - check if they darken; put broken ones back on shelves, mark them as broken. Check lens covers, replace as needed. Clear visibility but dark should be the norm. If can't see clearly, need to replace.
- Organize drills and charging stations
Dismantle brick press- Buff CEB press metal
- Paint CEB press metal
- Inventory grinders
- Inventory bolts
- Get 2 more acetylene bottles and 1 oxygen
- Get last materials - battry, press foot, pin, as by CAD
- Cut and weld cylinder
- Inventory old materials - grate etc
- Lay out hydraulic parts
- Lay out bolts
- Set up weld tables
- Make press foot spacers, 5.5x11.5"
- Cut 7" rebar reinforcements
- Bring hoist over
- Fire up tractor
Torching
- Strikers in good shape
- 4 torch sets functional; bottles full; tips clean