Power Cube/Manufacturing Instructions/Fabrication June 2011: Difference between revisions
mNo edit summary |
|||
| (23 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
=Power Cube 4.0 Construction= | =Power Cube 4.0 Construction= | ||
[[Image:PowerCubeFrameCAD.jpg]] | [[Image:PowerCubeFrameCAD.jpg|800px]] | ||
Here's how to replicate our Powercube 4.0 design. Keep in mind that this the powercube is still at the prototype stages and designs are likely to change. | Here's how to replicate our Powercube 4.0 design. Keep in mind that this the powercube is still at the prototype stages and designs are likely to change. There's also a few fittings /wires that are not reflected in this design. Aside from that, there should be enough information here to construct your very own OSE PowerCube 4.0! | ||
<html> | |||
<iframe width="425" height="349" src="https://www.youtube.com/embed//NEYMDD9T718" frameborder="0" allowfullscreen></iframe></html> | |||
<html> | |||
<iframe width="425" height="349" src="https://www.youtube.com/embed//703w_qBifXY" frameborder="0" allowfullscreen></iframe> | |||
</html> | |||
All designs, CAD drawings, media and documentation are mirrored on [http://openpario.net/projects/powercube/documents OpenPario]. | |||
| Line 15: | Line 22: | ||
| align="center" style="background:#f0f0f0;"|'''Quantity''' | | align="center" style="background:#f0f0f0;"|'''Quantity''' | ||
| align="center" style="background:#f0f0f0;"|'''Dimensions''' | | align="center" style="background:#f0f0f0;"|'''Dimensions''' | ||
|- | |- | ||
| '''ENGINE ASSEMBLY'''||1 | | '''ENGINE ASSEMBLY'''||1|| | ||
|- | |- | ||
| Engine ||1 | | Engine ||1|| | ||
|- | |- | ||
| Mounting Plate - Hydraulic Motor||1|| 8"x10"x1/4" | | Mounting Plate - Hydraulic Motor||1|| 8"x10"x1/4" | ||
|- | |- | ||
| Connector Plate||1||8"x3.75"x1/4" | | Connector Plate||1||8"x3.75"x1/4" | ||
|- | |- | ||
| Mounting Angle||2||8"x(2"x1/4") | | Mounting Angle||2||8"x(2"x1/4") | ||
|- | |- | ||
| Engine Mount Plate||1||8"x23"x1/4" | | Engine Mount Plate||1||8"x23"x1/4" | ||
|- | |- | ||
| Lovejoy Coupler||1||2.5"x2.25" | | Lovejoy Coupler||1||2.5"x2.25" | ||
|- | |- | ||
| Hydraulic Motor||1 | | Hydraulic Motor||1|| | ||
|- | |- | ||
| Gas Tank||1||14"x6"x6" | | Gas Tank||1||14"x6"x6" | ||
|- | |- | ||
| '''FUEL FILTER ASSEMBLY'''||1 | | '''FUEL FILTER ASSEMBLY'''||1|| | ||
|- | |- | ||
| Fuel Filter Fitting||1 | | Fuel Filter Fitting||1|| | ||
|- | |- | ||
| Fuel Filter||1||3.5"x5" | | Fuel Filter||1||3.5"x5" | ||
|- | |- | ||
| '''FRAME ASSEMBLY'''||1||24"x27.5"x30" | | '''FRAME ASSEMBLY'''||1||24"x27.5"x30" | ||
|- | |- | ||
| 24" Angle ||4||24"x(2"x1/4") | | 24" Angle ||4||24"x(2"x1/4") | ||
|- | |- | ||
| 27" Angle ||4||27"x(2"x1/4") | | 27" Angle ||4||27"x(2"x1/4") | ||
|- | |- | ||
| 29" Angle ||6||29"x(2"x1/4") | | 29" Angle ||6||29"x(2"x1/4") | ||
|- | |- | ||
| '''HYDRAULIC TANK ASSEMBLY'''||1||19"x29"x4" | | '''HYDRAULIC TANK ASSEMBLY'''||1||19"x29"x4" | ||
|- | |- | ||
| Hydraulic Tank Plates||2||19"x29"x1/4" | | Hydraulic Tank Plates||2||19"x29"x1/4" | ||
|- | |- | ||
| Flat - Hydraulic Sides||2||19"x3.5"x1/4" | | Flat - Hydraulic Sides||2||19"x3.5"x1/4" | ||
|- | |- | ||
| Flat - Hydraulic Bottom/Top||2||3.5"x28.5"x1/4" | | Flat - Hydraulic Bottom/Top||2||3.5"x28.5"x1/4" | ||
|- | |- | ||
| Battery||1||5"x6"x7.5" | | Battery||1||5"x6"x7.5" | ||
|- | |- | ||
| Hydraulic Mount||2||4.75"x3" | | Hydraulic Mount||2||4.75"x3" | ||
|} | |} | ||
==Total Metal to Purchase== | ==Total Metal to Purchase (summary)== | ||
{| | {| | ||
| Line 91: | Line 97: | ||
<iframe width="560" height="349" src="https://www.youtube.com/embed//1InlPCks6cE" frameborder="0" allowfullscreen></iframe> | <iframe width="560" height="349" src="https://www.youtube.com/embed//1InlPCks6cE" frameborder="0" allowfullscreen></iframe> | ||
</html> | </html> | ||
[[Image:PowerCubeFramePhoto.jpg|600px]] | |||
The frame is assembled in halves, and tack/welded in place. A completed frame should look like like this. | The frame is assembled in halves, and tack/welded in place. A completed frame should look like like this. | ||
[[Image:PowerCubeFrameSketch.jpg| | [[Image:PowerCubeFrameSketch.jpg|800px]] | ||
Note the overlap order. Short angles (green) on the outside. | |||
Assuming everything goes well on the welding, you should have your very own OSE PowerCube 4.0 Frame! | |||
[[Image:PowerCubeFramePic.jpg|800px]] | |||
==Assembly== | ==Assembly== | ||
[[Image:PowerCubeFrameAssembly.jpg]] | [[Image:PowerCubeFrameAssembly.jpg]] | ||
The open frame of the power cube makes assembly a snap. Just slide pieces into place, tack and weld away. Later designs will likely feature a little less intensive welding, but for now, it is a solid construction technique. | |||
===Mounting Assembly=== | ===Mounting Assembly=== | ||
[[Image:MountingCAD.jpg]] | [[Image:MountingCAD.jpg]] | ||
<html> | <html> | ||
<iframe width="425" height="349" src="https://www.youtube.com/embed//LnCRry5oPpc" frameborder="0" allowfullscreen></iframe> | <iframe width="425" height="349" src="https://www.youtube.com/embed//LnCRry5oPpc" frameborder="0" allowfullscreen></iframe> | ||
</html> | </html> | ||
[[Image:HydraulicMountPlate4.jpg]] | |||
[[Image:EngineMountPlate4.jpg]] | |||
[[Image:PowerCubeEngine4.jpg]] | |||
===Hydraulic Tank Assembly=== | ===Hydraulic Tank Assembly=== | ||
[[Image:HydraulicTankCAD.jpg]] | [[Image:HydraulicTankCAD.jpg]] | ||
Lay out a plate, tack and weld the 3.5" wide pieces vertically in a box shape atop it. Then lay the top plate atop and weld it in place. | |||
[[Image:HydraulicTankCADHoles.jpg]] | |||
Torch out holes in the top plate in the corners. 2" holes with the center 2"x2" offset from the sides | |||
<html> | <html> | ||
<iframe width="425" height="349" src="https://www.youtube.com/embed//GT957CJQNNo" frameborder="0" allowfullscreen></iframe> | <iframe width="425" height="349" src="https://www.youtube.com/embed//GT957CJQNNo" frameborder="0" allowfullscreen></iframe> | ||
</html> | </html> | ||
This would be a good time to break out the soap bubbles and test for leaks on the weld. Assuming the tank is tight, go ahead and move it on into the frame and weld it in place. Spacers may be needed on the sides near the top to keep everything snug. | |||
===Final=== | ===Final=== | ||
Mount the hydraulic fittings, hydraulic motor, gas tank, battery and wires. Finish it up to complete your very own OSE Powercube 4.0! | |||
<html> | <html> | ||
<iframe width="560" height="349" src="https://www.youtube.com/embed//V78idrurW5U" frameborder="0" allowfullscreen></iframe> | <iframe width="560" height="349" src="https://www.youtube.com/embed//V78idrurW5U" frameborder="0" allowfullscreen></iframe> | ||
</html> | </html> | ||
---- | |||
= Jig (optional) = | = Jig (optional) = | ||
| Line 189: | Line 220: | ||
[[Image:Jig.jpg|400px]] | [[Image:Jig.jpg|400px]] | ||
Jig Fully Assembled. | Jig Fully Assembled. | ||
=Muffler= | |||
==Muffler Mound CAD== | |||
In QCad: | |||
[[Image:mufflermount.jpg]] | |||
Uploaded to Open Pario - [http://openpario.net/documents/1236] | |||
CAM file from [[DXF to G-code Converter]]: | |||
[[Image:mufflermountCAM.jpg]] | |||
Uploaded to Open Pario - [http://openpario.net/documents/1236] | |||
[[Category: Power Cube]] | [[Category: Power Cube]] | ||
Latest revision as of 21:19, 5 February 2012
Power Cube 4.0 Construction
Here's how to replicate our Powercube 4.0 design. Keep in mind that this the powercube is still at the prototype stages and designs are likely to change. There's also a few fittings /wires that are not reflected in this design. Aside from that, there should be enough information here to construct your very own OSE PowerCube 4.0!
All designs, CAD drawings, media and documentation are mirrored on OpenPario.
BOM
| Name | Quantity | Dimensions |
| ENGINE ASSEMBLY | 1 | |
| Engine | 1 | |
| Mounting Plate - Hydraulic Motor | 1 | 8"x10"x1/4" |
| Connector Plate | 1 | 8"x3.75"x1/4" |
| Mounting Angle | 2 | 8"x(2"x1/4") |
| Engine Mount Plate | 1 | 8"x23"x1/4" |
| Lovejoy Coupler | 1 | 2.5"x2.25" |
| Hydraulic Motor | 1 | |
| Gas Tank | 1 | 14"x6"x6" |
| FUEL FILTER ASSEMBLY | 1 | |
| Fuel Filter Fitting | 1 | |
| Fuel Filter | 1 | 3.5"x5" |
| FRAME ASSEMBLY | 1 | 24"x27.5"x30" |
| 24" Angle | 4 | 24"x(2"x1/4") |
| 27" Angle | 4 | 27"x(2"x1/4") |
| 29" Angle | 6 | 29"x(2"x1/4") |
| HYDRAULIC TANK ASSEMBLY | 1 | 19"x29"x4" |
| Hydraulic Tank Plates | 2 | 19"x29"x1/4" |
| Flat - Hydraulic Sides | 2 | 19"x3.5"x1/4" |
| Flat - Hydraulic Bottom/Top | 2 | 3.5"x28.5"x1/4" |
| Battery | 1 | 5"x6"x7.5" |
| Hydraulic Mount | 2 | 4.75"x3" |
Total Metal to Purchase (summary)
| Type | Width | Thickness | Total Length (rounded up) |
| Angle | 2" | 1/4" | 400" |
| Plate | 19" | 1/4" | 60" |
| Plate | 8" | 1/4" | 40" |
| Plate | 6" | 1/4" | 12" |
| Plate | 3.5" | 1/4" | 100" |
| Tube | 6" | 1/4" | 14" |
Frame
The Power Cube 4.0 (as of this prototype at least) is not actually a strict cube. But more of a lopsided box.) The longest dimensions are on the side (left to right), while the shortest dimension is up/down. See below.
The frame is assembled in halves, and tack/welded in place. A completed frame should look like like this.
Note the overlap order. Short angles (green) on the outside.
Assuming everything goes well on the welding, you should have your very own OSE PowerCube 4.0 Frame!
Assembly
The open frame of the power cube makes assembly a snap. Just slide pieces into place, tack and weld away. Later designs will likely feature a little less intensive welding, but for now, it is a solid construction technique.
Mounting Assembly
Hydraulic Tank Assembly
Lay out a plate, tack and weld the 3.5" wide pieces vertically in a box shape atop it. Then lay the top plate atop and weld it in place.
Torch out holes in the top plate in the corners. 2" holes with the center 2"x2" offset from the sides
This would be a good time to break out the soap bubbles and test for leaks on the weld. Assuming the tank is tight, go ahead and move it on into the frame and weld it in place. Spacers may be needed on the sides near the top to keep everything snug.
Final
Mount the hydraulic fittings, hydraulic motor, gas tank, battery and wires. Finish it up to complete your very own OSE Powercube 4.0!
Jig (optional)
The jig is an optional piece of fabrication equipment that can be very useful to have should you be creating several power cubes concurrently. The materials for the cube are assembled in the jig in half sections and tacked and welded in place.
Materials List
Total Length 14' Angle (2"x1/4") 7'2" Rebar (1/2")
Cut List
| Type | Length | Dimensions | Quantity | Color |
| Angle | 22" | (2"x1/4") | 2 | (red) |
| Angle | 26" | (2"x1/4") | 2 | (yellow) |
| Angle | 29" | (2"x1/4") | 2 | (green) |
| Rebar | 30.5" | (1/2") | 1 | |
| Rebar | 27" | (1/2") | 2 |
Assembly of the Jig is fairly straight forward. Tack and weld the pieces in place.
Be sure to note the overlapping order and the notch made at the bottom of the 1'10 1/4" piece (red). Torch holes in the corners below the frame as seen above. This allows room for the welding torch to get to the PowerCube while welding.
Also note that the corners are offset 3/4" (1/2" measured on the interior), to give room for the cube to sit snugly in the frame (and a convenient gap for welding the corners.)
Tack weld the two shorter rebar sections at roughly a 45 degree angle on the sides. Add a long rebar section to span the gap. Precision is not as important with these, they are more there for stability.
With any luck, you'll have your jig, ready to crank out Power Cubes with!
Jig Fully Assembled.
Muffler
Muffler Mound CAD
In QCad:
Uploaded to Open Pario - [1]
CAM file from DXF to G-code Converter:
Uploaded to Open Pario - [2]