April 2011 Production Run Hydraulics BOM

This page is currently under construction and might undergo drastic changes within a short span of time.

Tractor

See Parts Sourcing for contact information. Note: this includes hydraulics and balance of system after metal.

1. [8] 1-7/8" Flange Bearings - [1] ; plus BearingsOn plus Big Bearing Store
2. [2] Front Loader cylinders - 36" - $174 - 48 5/8" retracted length - [2] & [2] of [[3]]
3. [8] 3/8 NPTM x 1/2 NPTF 90 SWIVEL [4] for Loader and QA Plate cylinders [5]
4. [4] Motors - [6]
   1. [8] SAE M 10 to NPT M 1/2" for Ports [7]
   2. [4] SAE 4M TO 1/4" NPTM CONNECTOR for Case Drains [8]
   3. [8] 1/2" QC for Motors [9]
   4. [4] 1/4" QC for motors [10]
5. [2] 1-1/4 SHAFT COUPLER W 5/16" KEYWAY - [11]
6. [1 1/3] 1-3/8" 6T fully splined shafting - [12]
7. [2] Female 1-3/8" 6T spline coupling - [13], $30 each
8. [12] 1.875" double split shaft collars - [14]
9. Double split - $11 - [15]
10. Double split - $9 -Houston Bearing
11. Double split - $9 free ship - [16]
12. Single split - [17]

Motor Valves

• [1] 3-spool motor valve, 25 gpm - [18], $288
• [4] 1/2" Quick Couplers [19] - for motor valve work ports
• [2] 3/4" Quick Couplers for one set of motor valve work ports - Dalton Hydraulics
• [4] 1/2" Swivels for work ports [20] - for 2 sets of work ports to wheel motors
• [1] 3/4" tee for inlet - [21]
• [1] 3/4" elbow for inlet - [22]
• [2] 30 GPM check valves for inlet - [23]
• [2] 3/4" QC for inlet - Dalton
• [5] 3/4"nips for inlet including valve in/out - [24]
• [2] 1/2 NPT hex nipples [25]-for auxiliary pair of motor valve work ports
• [2] 3/4 NPT to 1/2 NPT bushing [26] - auxiliary work ports - NA

Loader Valve

• [1] Prince 2 Spool Valve - [27] $189
• [1] 3/4" NPT nip for outlet - [28]
• [4] 1/2" Swivels for work ports [29] - for 2 sets of work ports to wheel motors
• [1] 3/4" QC for outlet
• [2] 1/2" tees to split to 2 cylinders

Cushion Valves

• [1] 1/2 NPT 30 GPM 1500-3000 PSI HYD CUSHION VALVES - [30]
• [6] 1/2" swivels [31] - 4 valve outlet + 2 cushion valve
• [2] 1/2" nip - [32] - going from between swivel and tee
• [4] NPTF Tee [33]- (includes QA plates

Power Cube

• [1] Pump - 0.98 cu in - [34]
• [1] SAE 12 in to 3/4 hosebarb- [35]
• [1] SAE 10 out to 1/2 NPT - [36]
• [1] 3/4 to 1/2 reducer bushing - NA
• [1] Coupler half, 5/8" - $10
• [1] Coupler half, 1 1/8" - $10
• [1] Solid spider - $14
• [1] Suction strainer, 2" to 1-1/4" - [37] - $23
• [1] 3" suction strainer - [38] - $42
• [1] Pressure relief for power cube bypass- [39]
• [1] 20 GPM return Line Filter - [40]
• 1" female coupling into frame
• [1] 1" nip to filter - [41]
• [1] 30 GPM return Line Filter - [42]
• [1] 1"-3/4" reducer bushing - [43]
• [2] 3/4" nip - [44]
• [1] 30 gpm Quick Coupler

• [1] 1"-3/4" NPT reducer bushing for frame receptacle for return filter - [45]
• [1] 3/4" quick coupler for return line to filter
• [2] 1/2" quick couplers for main power lines

Soil Pulverizer

• Hydraulic PTO Motor -
• 10' hose -

Hoses

Power Cube

• [1] 2 foot hose from pump outlet to return line filter - [46]
• [2] 10 foot hoses, already have these - [47]

Pressure Bypass

• [1] 1/2" NPT Bypass valve - [48]
• [3] 1/2" Quick couplers - 1 complete for tee near pump, one going from return filter to tee, and male tip for return line. This gives one extra female quick coupler left over. This set of 3 QCs does not cover hoses going from and to the PowerCube.
• [4] 1/2" NPTF hex nip for one and other side of tee, on both tees - [49]
• [2] 1/2" NPTF tee - from outlet of pump to pressure bypass, and from bypass valve into return line filter - [50]

Between Motor Valves & Motors

• [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of the valves [51]
• [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of front motors [52]
• [4] 1/2 X 1/2 X 1/2 NPTF TEE [53]
• [4] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for rear motors [54]

Motor Case Drains

• [2] 1/4" X 72" NPTM 2750 PSI HYD HOSE to run parallel with tractor sides [55]
• [1] 1/4" X 30" NPTM 2750 PSI HYD HOSE from Tee to Tee in return hose [56]
• [1] 1/4" X 36" NPTM 2750 PSI HYD HOSE to Rear Motors [57]
• [3] 1/4 X 1/4 X 1/4 NPTF TEE [58]
• [3] 1/4 NPT hex nipples [59]
• [4] 1/4" NPT quick couplers are already with the motors

Front Loader

• [2] 1/2" X 12" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE from Valves to Cushion [60]
• [2] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for left front loader cylinder [61]
• [1] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [62]
• [1] 1/2" X 60" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [63]

Front loader QA Cylinder Hoses

• [4] 3/8" NPTM x 1/2" NPTF swivel - [64] - swivels for QA cylinders
• [2] 1/2" nips - going from cylinder swivels to tees - [65]
• [2] 1/2" NPTF tees - from cylinder to hoses - [66]
• [2] male QC tips - for plugging into control valves - [67]
• [2] 1/2" X 48" NPTM 3000 PSI HYD HOSE [68]
• [1] 1/2" X 120" NPTM 3000 PSI HYD HOSE [69]
• [1] 1/2" X 144" NPTM 3000 PSI HYD HOSE [70]