Stepper motors: Difference between revisions
(Redirected page to Torch Table Bill of Materials) |
|||
| Line 1: | Line 1: | ||
{{Template:Category=Torch Table}} | |||
Stepper motors for [[Torch Table]] are from [http://www.xylotex.com/Econo3Ax425.htm Xylotex]. | |||
Stepper motors: | |||
[[Image:steppers.jpg]] | |||
Controller: | |||
[[Image:controller.jpg]] | |||
Possible limit switch configuration: | |||
[[Image:limitswitch.jpg]] | |||
Setting fractional steps on stepper motors: | |||
[[Image:fractionalsteps.jpg]] | |||
=Specs= | |||
*1/4" shaft | |||
*425 in oz torque | |||
*about 50 W power usage | |||
[[Image:xylotex4axisspecs.jpg]] | |||
The XS-3525/8S-4 microtepping stepper motor driver is the perfect choice for CNC retrofitting of desktop and small benchtop milling machines. Connect bipolar wired stepper motors, power, and parallel port signal source. | |||
*Small Size 4.275 x 2.8? inches. | |||
*Drives up to 35 Volts @ 2.5 A/phase | |||
*4 different microstepping step levels from Full-Step(FS) to 1/8 step | |||
*Filtered & Buffered Step & Dir lines | |||
*Built in DC-DC converter for +5V | |||
*Break-out screw terminals for I/O | |||
'''Microstepping Truth Table''' | |||
{| cellpadding="6" cellspacing="0" border="1" align="left" | |||
! axS1 | |||
! axS0 | |||
! Output | |||
|-align="left" | |||
! 0 | |||
! 0 | |||
! Full Step | |||
|-align="left" | |||
! 0 | |||
! 1 | |||
! Half Step | |||
|-align="left" | |||
! 1 | |||
! 0 | |||
! Quarter Step | |||
|-align="left" | |||
! 1 | |||
! 1 | |||
! Eighth Step | |||
|} | |||
1 means jumper NOT installed | |||
The XS-3535/8S-4 Stepper Driver is a 4 axis pulse-width-modulated (PWM) current controlled bipolar micro-stepping controller. | |||
Each axis drive has a +-2.5 Amp/phase @ 35 Volt maximum continuous Output Rating. The drive circuitry has thermal shutdown protection and crossover-current protection. Synchronous rectification circuitry eliminates the need for external clamp diodes in most applications. | |||
Each axis accepts Step & Direction signals, along with 2 jumper inputs to define microsteps per full step. | |||
The board is of 4-Later construction with Isolated Power and Logic supply planes. The drive circuitry has a heat sink attached to allow cooler operation. | |||
[[Category:Torch Table]] | |||
Revision as of 21:51, 29 May 2012
Main > Digital Fabrication > RepLab Tools > Torch Table
Stepper motors for Torch Table are from Xylotex.
Stepper motors:
Controller:
Possible limit switch configuration:
Setting fractional steps on stepper motors:
Specs
- 1/4" shaft
- 425 in oz torque
- about 50 W power usage
The XS-3525/8S-4 microtepping stepper motor driver is the perfect choice for CNC retrofitting of desktop and small benchtop milling machines. Connect bipolar wired stepper motors, power, and parallel port signal source.
- Small Size 4.275 x 2.8? inches.
- Drives up to 35 Volts @ 2.5 A/phase
- 4 different microstepping step levels from Full-Step(FS) to 1/8 step
- Filtered & Buffered Step & Dir lines
- Built in DC-DC converter for +5V
- Break-out screw terminals for I/O
Microstepping Truth Table
| axS1 | axS0 | Output |
|---|---|---|
| 0 | 0 | Full Step |
| 0 | 1 | Half Step |
| 1 | 0 | Quarter Step |
| 1 | 1 | Eighth Step |
1 means jumper NOT installed
The XS-3535/8S-4 Stepper Driver is a 4 axis pulse-width-modulated (PWM) current controlled bipolar micro-stepping controller.
Each axis drive has a +-2.5 Amp/phase @ 35 Volt maximum continuous Output Rating. The drive circuitry has thermal shutdown protection and crossover-current protection. Synchronous rectification circuitry eliminates the need for external clamp diodes in most applications.
Each axis accepts Step & Direction signals, along with 2 jumper inputs to define microsteps per full step.
The board is of 4-Later construction with Isolated Power and Logic supply planes. The drive circuitry has a heat sink attached to allow cooler operation.