April 2011 Production Run Hydraulics BOM

From Open Source Ecology
Jump to navigation Jump to search

Generator

  1. [1] hydraulic motor for direct 1800RPM generator drive - [1]
  2. [1] 5/8" coupler - [2]

Other

  1. [1] Power Cube Throttle Cable - [3] - need 5

Tractor

See Parts Sourcing for contact information. Note: this includes hydraulics and balance of system after metal.

  1. [8] 1-7/8" Flange Bearings - [4] ; plus BearingsOn plus Big Bearing Store
  2. [2] Front Loader cylinders - 36" - $174 - 48 5/8" retracted length - [5] & [2] of [[6]]
  3. [8] 3/8 NPTM x 1/2 NPTF 90 SWIVEL [7] for Loader and QA Plate cylinders [8]
  4. [4] Motors - [9]
    1. [8] SAE M 10 to NPT M 1/2" for Ports [10]
    2. [4] SAE 4M TO 1/4" NPTM CONNECTOR for Case Drains [11]
    3. [8] 1/2" QC for Motors [12]
    4. [4] 1/4" QC for motors [13]
  5. [2] 1-1/4 SHAFT COUPLER W 5/16" KEYWAY - [14]
  6. [1 1/3] 1-3/8" 6T fully splined shafting - [15]
  7. [2] Female 1-3/8" 6T spline coupling - [16], $17 each
  8. [12] 1.875" double split shaft collars - [17]
  9. Double split - $11 - [18]
  10. Double split - $9 -Houston Bearing
  11. Double split - $9 free ship - [19]
  12. Single split - [20]

Motor Valves

  • [1] 3-spool motor valve, 25 gpm - [21], $288
  • [2] 3/4" Nips [22] (includes cylinder valve)
  • [1] 3/4" swivel - [23]
  • [2] 3/4" Quick Couplers for one set of motor valve work ports - Dalton Hydraulics
  • [4] 1/2" Swivels for work ports [24] - for 2 sets of work ports to wheel motors
  • [1] 3/4" tee for inlet - [25]
  • [1] 3/4" elbow for inlet - [26]
  • [2] 30 GPM check valves for inlet - [27]
  • [2] 3/4" QC for inlet - Dalton
  • [5] 3/4"nips for inlet including valve in/out - [28]
  • [2] 1/2 NPT hex nipples [29]-for auxiliary pair of motor valve work ports
  • [2] 3/4 NPT to 1/2 NPT bushing [30] - auxiliary work ports - NA

Loader Valve

  • [1] Prince 2 Spool Valve - [31] $189
  • [1] 3/4" NPT nip for outlet - [32]
  • [4] 1/2" Swivels for work ports [33] - for 2 sets of work ports to wheel motors
  • [1] 3/4" QC for outlet
  • [2] 1/2" tees to split to 2 cylinders

Cushion Valve

  • [1] 1/2 NPT 30 GPM 1500-3000 PSI HYD CUSHION VALVES - [34]
  • [6] 1/2" swivels [35] - 4 valve outlet + 2 cushion valve
  • [2] 1/2" nip - [36] - going from between swivel and tee
  • [4] NPTF Tee [37]- (includes QA plates

Power Cube

  • [1] Pump - 0.98 cu in - [38]
  • [1] 3/4" coupler for exit - Dalton
  • [1] 3/4" breather cap -[39] - $13
  • [1] Filler Cap - [40]
  • [1] SAE 12 in to 3/4 hosebarb- [41]
  • [1] SAE 10 out to 1/2 NPT - [42]
  • [1] 3/4 to 1/2 reducer bushing - NA
  • [1] Coupler half, 5/8" - $10
  • [1] Coupler half, 1 1/8" - $10
  • [1] Solid spider - $14
  • [1] Suction strainer, 2" to 1-1/4" - [43] - $23
  • [1] Pressure relief for power cube bypass- [44]
  • [1] 20 GPM return Line Filter - [45] - 3 of these
  • 1" female coupling into frame
  • [1] 1" nip to filter - [46]
  • [1] 30 GPM return Line Filter - [47] - 3 total of these
  • [1] 1"-3/4" reducer bushing - [48]
  • [1] 3/4" tee - [49]
  • [2] 3/4" nip - [50]
  • [1] 30 gpm Quick Coupler to return line
  • [1] 3/4"-1/4" NPT reducer bushing for case drain - [51]
  • [1] 1/4" nip - [52]
  • [1] 1/4" quick couplers for case drain - [53]

Soil Pulverizer

  • [1] 7.6 cu in hydraulic PTO motor - [54]
  • [2] 10' hose - [55] $21
  • [2] 1-7/8" bearings - []
  • 6 tooth spline coupler - [56] (enough for 3)

Hoses

Power Cube

  • [2] 10 foot hoses - [57]

Motor Valves

  • [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of the valves [58]
  • [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of front motors [59]
  • [4] 1/2 X 1/2 X 1/2 NPTF TEE [60]
  • [4] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for rear motors [61]

Motor Case Drains

  • [2] 1/4" X 72" NPTM 2750 PSI HYD HOSE to run parallel with tractor sides [62]
  • [1] 1/4" X 30" NPTM 2750 PSI HYD HOSE from Tee to Tee in return hose [63]
  • [1] 1/4" X 36" NPTM 2750 PSI HYD HOSE to Rear Motors [64]
  • [3] 1/4 X 1/4 X 1/4 NPTF TEE [65]
  • [3] 1/4 NPT hex nipples [66]
  • [4] 1/4" NPT quick couplers are already with the motors

Front Loader

  • [2] 1/2" X 12" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE from Valves to Cushion [67]
  • [2] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for left front loader cylinder [68]
  • [1] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [69]
  • [1] 1/2" X 60" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [70]

QA Cylinder

  • [4] 3/8" NPTM x 1/2" NPTF swivel - [71] - swivels for QA cylinders
  • [2] 1/2" nips - going from cylinder swivels to tees - [72]
  • [2] 1/2" NPTF tees - from cylinder to hoses - [73]
  • [2] male QC tips - for plugging into control valves - [74]
  • [2] 1/2" X 48" NPTM 3000 PSI HYD HOSE [75]
  • [1] 1/2" X 120" NPTM 3000 PSI HYD HOSE [76]
  • [1] 1/2" X 144" NPTM 3000 PSI HYD HOSE [77]
Retrieved from "https://wiki.opensourceecology.org/index.php?title=April_2011_Production_Run_Hydraulics_BOM&oldid=24048"