Upload log

Below is a list of the most recent file uploads. See the gallery of new files for a more visual overview.

• 10:54, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:Rubber spacers00.jpg (Doubling the thickness.)
• 10:44, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:Y1 x square.jpg (Square mating of carriage of Y1 and short idler side of X.)
• 10:40, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:End stop y modified.jpg (Extension added on Y1 carriage to stop X before extruder hits Y1 motor. By doing this travel range on X is increased by 10mm.)
• 10:36, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:End stop x modified.jpg (Modified end stop on X to increase travel range.)
• 10:22, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:X axis parallel.jpg (Checking that x-axis is parallel to frame after installation.)
• 10:20, 9 January 2018 Cabeza de Pomelo talk contribs uploaded File:Rubber spacers.jpg (Heat resistant rubber spacers for heated bed.)
• 00:15, 9 January 2018 Marcin talk contribs uploaded File:OSE Marlin 1612.tar.gz (Initial Copy comes from OSE Linux, October 25, 2017 Version 1.0 release.)
• 05:49, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Clearance Y1 X.jpg (Clearance in the Y1-X corner)
• 05:46, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Range y.jpg (Range of movement on Y-axis. 188mm)
• 05:45, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Range X.jpg (Range of movement on X-axis. 191 mm)
• 05:42, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Sensor on.jpg (Inductive sensor in place.)
• 05:40, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Heat sink ext01.jpg (Vanes)
• 05:38, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Heat sink ext00.jpg (Trimmed extruder heat sink)
• 05:37, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Heat sink ext.jpg (Trimming extruder heat sink)
• 05:34, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Inductive install.jpg (Installing inductive sensor)
• 05:31, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Termistor connector.jpg (EO and HBP termistors in one connector. Recycle.)
• 05:23, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Axes configuration.jpg (Positions of axes and motors.)
• 05:20, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Install x.jpg (Access hole to tighten the bottom screw holding X-axis to the carriage.)
• 05:15, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:Belt tension.jpg (Tensioning belt by feel.)
• 05:12, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:One peg.jpg (Belt-tightening peg)
• 05:10, 6 January 2018 Cabeza de Pomelo talk contribs uploaded File:M6x30-2.jpg (Trimmed off 2mm from M6x30mm SS screws.)
• 11:15, 3 January 2018 Cabeza de Pomelo talk contribs uploaded File:All axes frame.jpg (The disposition of all axes on the metal frame.)
• 05:20, 3 January 2018 Marcin talk contribs uploaded a new version of File:CEB v1708 CAM.zip (Removed H6 and H7 from the 1/4" steel cuts. See last version.)
• 01:16, 2 January 2018 S Oberloier talk contribs uploaded File:RF Transmitter.png.png
• 00:55, 2 January 2018 S Oberloier talk contribs uploaded File:Non invert amplifier.png
• 00:11, 2 January 2018 S Oberloier talk contribs uploaded File:OCI.png
• 23:28, 1 January 2018 S Oberloier talk contribs uploaded File:PM 5V Supply.png
• 09:13, 1 January 2018 Cabeza de Pomelo talk contribs uploaded File:Controller wiring.jpg (Some of the wires to the controller.)
• 09:11, 1 January 2018 Cabeza de Pomelo talk contribs uploaded File:Soldering inductive sensor.jpg (Soldering inductive sensor's wires to Dupont end in the correct sequence.)
• 09:08, 1 January 2018 Cabeza de Pomelo talk contribs uploaded File:Inducive sensor dupont.jpg (Setting up wires to solder Dupont connector end to inductive sensor wiring.)
• 09:05, 1 January 2018 Cabeza de Pomelo talk contribs uploaded File:Sequence dupont.jpg (Changing wire sequence in Dupont connector.)
• 15:23, 31 December 2017 Ruslan talk contribs uploaded File:Create-elbow-alpha.FCMacro
• 15:12, 31 December 2017 Ruslan talk contribs uploaded File:Pvc-elbow-alpha-gui-screenshot.png
• 15:12, 31 December 2017 Ruslan talk contribs uploaded File:Pvc-elbow-alpha-cad-screenshot.png
• 15:12, 31 December 2017 Ruslan talk contribs uploaded File:Pvc-elbow-alpha-test.fcstd
• 22:37, 30 December 2017 Ruslan talk contribs uploaded a new version of File:Pvc-elbow-90-gui-screenshot.png
• 22:32, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:X y y.jpg (X and Y axes)
• 22:29, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Pulley alignment.jpg (Correct alignment.)
• 22:26, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Motor pulley ok.jpg (Correct placement of pulley.)
• 22:24, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Motor pulley ref.jpg (Used a bearing as a reference to accurately place the pulleys on the motors.)
• 22:21, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Short idler tight.jpg (A gap of around about 0.5mm must be seen between the two bearings)
• 22:19, 30 December 2017 Ruslan talk contribs uploaded a new version of File:Pvc-elbow-90-gui-screenshot.png (Reverted to version as of 22:16, 30 December 2017)
• 22:19, 30 December 2017 Ruslan talk contribs uploaded a new version of File:Pvc-elbow-90-gui-screenshot.png
• 22:16, 30 December 2017 Ruslan talk contribs uploaded a new version of File:Pvc-elbow-90-gui-screenshot.png
• 22:16, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:HBP temp.jpg (Maximum temperature reached by HBP without regulation.)
• 22:13, 30 December 2017 Ruslan talk contribs uploaded File:Create-elbow-90.FCMacro
• 22:13, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Idler flanges on.jpg (Printed flanges for idler bearings.)
• 22:08, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Square interface carriage.jpg (Proper alignment of parts after gluing the magnets.)
• 22:05, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Magnets epoxy.jpg (Beads of epoxy on extruder interface.)
• 22:02, 30 December 2017 Cabeza de Pomelo talk contribs uploaded File:Magnets extruder interface.jpg (Sticking the magnets of the extruder interface to the carriage assembly before gluing.)