April 2011 Production Run Hydraulics BOM

From Open Source Ecology
Jump to navigation Jump to search

Under construction icon.png This page is currently under construction and might undergo drastic changes within a short span of time.


Tractor

See Parts Sourcing for contact information. Note: this includes hydraulics and balance of system after metal.

  1. [8] 1-7/8" Flange Bearings - [1] ; plus BearingsOn plus Big Bearing Store
  2. [2] Front Loader cylinders - 36" - $174 - 48 5/8" retracted length - [2] & [2] of [[3]]
  3. [8] 3/8 NPTM x 1/2 NPTF 90 SWIVEL [4] for Loader and QA Plate cylinders [5]
  4. [4] Motors - [6]
    1. [8] SAE M 10 to NPT M 1/2" for Ports [7]
    2. [4] SAE 4M TO 1/4" NPTM CONNECTOR for Case Drains [8]
    3. [8] 1/2" QC for Motors [9]
    4. [4] 1/4" QC for motors [10]
  5. [2] 1-1/4 SHAFT COUPLER W 5/16" KEYWAY - [11]
  6. [1 1/3] 1-3/8" 6T fully splined shafting - [12]
  7. [2] Female 1-3/8" 6T spline coupling - [13], $30 each
  8. [12] 1.875" double split shaft collars - [14]
  9. Double split - $11 - [15]
  10. Double split - $9 -Houston Bearing
  11. Double split - $9 free ship - [16]
  12. Single split - [17]


Motor Valves

  • [1] 3-spool motor valve, 25 gpm - [18], $288
  • [4] 1/2" Quick Couplers [19] - for motor valve work ports
  • [2] 3/4" Quick Couplers for one set of motor valve work ports - Dalton Hydraulics
  • [4] 1/2" Swivels for work ports [20] - for 2 sets of work ports to wheel motors
  • [1] 3/4" tee for inlet - [21]
  • [1] 3/4" elbow for inlet - [22]
  • [2] 30 GPM check valves for inlet - [23]
  • [2] 3/4" QC for inlet - Dalton
  • [5] 3/4"nips for inlet including valve in/out - [24]
  • [2] 1/2 NPT hex nipples [25]-for auxiliary pair of motor valve work ports
  • [2] 3/4 NPT to 1/2 NPT bushing [26] - auxiliary work ports - NA

Loader Valve

  • [1] Prince 2 Spool Valve - [27] $189
  • [1] 3/4" NPT nip for outlet - [28]
  • [4] 1/2" Swivels for work ports [29] - for 2 sets of work ports to wheel motors
  • [1] 3/4" QC for outlet
  • [2] 1/2" tees to split to 2 cylinders

Cushion Valves

  • [1] 1/2 NPT 30 GPM 1500-3000 PSI HYD CUSHION VALVES - [30]
  • [6] 1/2" swivels [31] - 4 valve outlet + 2 cushion valve
  • [2] 1/2" nip - [32] - going from between swivel and tee
  • [4] NPTF Tee [33]- (includes QA plates

Power Cube

  • [1] Pump - 0.98 cu in - [34]
  • [1] SAE 12 in to 3/4 hosebarb- [35]
  • [1] SAE 10 out to 1/2 NPT - [36]
  • [1] 3/4 to 1/2 reducer bushing - NA
  • [1] Coupler half, 5/8" - $10
  • [1] Coupler half, 1 1/8" - $10
  • [1] Solid spider - $14
  • [1] Suction strainer, 2" to 1-1/4" - [37] - $23
  • [1] 3" suction strainer - [38] - $42
  • [1] Pressure relief for power cube bypass- [39]
  • [1] 20 GPM return Line Filter - [40]
  • 1" female coupling into frame
  • [1] 1" nip to filter - [41]
  • [1] 30 GPM return Line Filter - [42]
  • [1] 1"-3/4" reducer bushing - [43]
  • [2] 3/4" nip - [44]
  • [1] 30 gpm Quick Coupler
  • [1] 1"-3/4" NPT reducer bushing for frame receptacle for return filter - [45]
  • [1] 3/4" quick coupler for return line to filter
  • [2] 1/2" quick couplers for main power lines

Soil Pulverizer

  • Hydraulic PTO Motor -
  • 10' hose -

Hoses

Power Cube

  • [1] 2 foot hose from pump outlet to return line filter - [46]
  • [2] 10 foot hoses, already have these - [47]

Pressure Bypass

  • [1] 1/2" NPT Bypass valve - [48]
  • [3] 1/2" Quick couplers - 1 complete for tee near pump, one going from return filter to tee, and male tip for return line. This gives one extra female quick coupler left over. This set of 3 QCs does not cover hoses going from and to the PowerCube.
  • [4] 1/2" NPTF hex nip for one and other side of tee, on both tees - [49]
  • [2] 1/2" NPTF tee - from outlet of pump to pressure bypass, and from bypass valve into return line filter - [50]


Between Motor Valves & Motors

  • [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of the valves [51]
  • [4] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for in/out of front motors [52]
  • [4] 1/2 X 1/2 X 1/2 NPTF TEE [53]
  • [4] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for rear motors [54]

Motor Case Drains

  • [2] 1/4" X 72" NPTM 2750 PSI HYD HOSE to run parallel with tractor sides [55]
  • [1] 1/4" X 30" NPTM 2750 PSI HYD HOSE from Tee to Tee in return hose [56]
  • [1] 1/4" X 36" NPTM 2750 PSI HYD HOSE to Rear Motors [57]
  • [3] 1/4 X 1/4 X 1/4 NPTF TEE [58]
  • [3] 1/4 NPT hex nipples [59]
  • [4] 1/4" NPT quick couplers are already with the motors

Front Loader

  • [2] 1/2" X 12" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE from Valves to Cushion [60]
  • [2] 1/2" X 36" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for left front loader cylinder [61]
  • [1] 1/2" X 48" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [62]
  • [1] 1/2" X 60" 1/2 NPTM X 1/2 NPTM 3000 PSI HYD HOSE for right front loader cylinder [63]

Front loader QA Cylinder Hoses

  • [4] 3/8" NPTM x 1/2" NPTF swivel - [64] - swivels for QA cylinders
  • [2] 1/2" nips - going from cylinder swivels to tees - [65]
  • [2] 1/2" NPTF tees - from cylinder to hoses - [66]
  • [2] male QC tips - for plugging into control valves - [67]
  • [2] 1/2" X 48" NPTM 3000 PSI HYD HOSE [68]
  • [1] 1/2" X 120" NPTM 3000 PSI HYD HOSE [69]
  • [1] 1/2" X 144" NPTM 3000 PSI HYD HOSE [70]
Retrieved from "https://wiki.opensourceecology.org/index.php?title=April_2011_Production_Run_Hydraulics_BOM&oldid=23825"