Alex Kit Certification: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
(14 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
= | =Build Space= | ||
Make a copy of: | |||
<html><iframe src="https://docs.google.com/presentation/d/e/2PACX-1vSdnEaF2sf2ORPESJhIb1Bhquov-ZOh5sjbFAgT_BcNSyee0Q12eUFTsMdb6r4HEsrO17KvC3gozMSN/embed?start=false&loop=false&delayms=3000" frameborder="0" width="960" height="569" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe></html> | |||
[https://docs.google.com/presentation/d/1KGWenTMrttuJIoEpXvef1ICN8QQa0vD1EA0LrJm4tQA/edit#slide=id.g4071900322_0_32 edit] | |||
=Main Certification Spreadsheet= | |||
make a copy of Sara's - https://docs.google.com/spreadsheets/d/1k1qLG1_LydebeziBzCr1ePvJ2fdkDO85xidjKrGdd9I/edit#gid=0 | |||
=Electronics Certification= | |||
make copy of https://docs.google.com/presentation/d/1tuqGoRbD_J-1NZOyky5YsDny67ybINcYIUi9IxU4gtc/edit#slide=id.g4071900322_0_32 | |||
=Kit Inventory= | =Kit Inventory= | ||
Line 11: | Line 22: | ||
[https://docs.google.com/spreadsheets/d/1FhlzOXlx9gDl9IkadzLJBlQ7obsZjdiJURAZUjvUyVM/edit#gid=440076612 edit] | [https://docs.google.com/spreadsheets/d/1FhlzOXlx9gDl9IkadzLJBlQ7obsZjdiJURAZUjvUyVM/edit#gid=440076612 edit] | ||
=Evaluation= | |||
<html><iframe width="560" height="315" src="https://www.youtube.com/embed/EVK28rUZct8" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html> | |||
Kit build went well. There were missing parts (not printed) that were substituted (first picture in video above), and some issues: | |||
#LCD did not work | |||
#LCD location on control panel was in the way of the cable chain due to old documentation (main documentation has been since updated) | |||
#Printed carriages needed cleaning | |||
#There was an additional hole in the front frame piece which marcin mistook for a Z axis hole, only to find out that it did not have the opposing hole, and this resulted in a build error. I had to redrill a hole for the second Z. | |||
#Frame had old epoxy on it. Had to clean it with a knife and grinder. | |||
#It turns out that 8 mm shafts were tight. I replaced X and Y shafts with 5/16" shafts. This issue may depend on filament and printer - for the printed part quality. I left the Z axes at 8 mm - but needed extra glide on X and Y for speed. | |||
#Back bottom Z axis hole was too far down for the Z axis to fit - had to redrill the hole higher. | |||
#Two bed standoff nuts did not fit on 8 mm rods - used other nuts | |||
#Wire on the Z probe connector - excessively long, had to wrap up many more times in the final wiring. Works, but took more time. | |||
#Control panel - MOSFET too close to USB plug - needs to go a little to the right, and need to correct instructions. Also, needs 3rd mounting hole on MOSFET so the MOSFET doesn't slouch forward. | |||
#Spool holder pieces had to be reamed out (heated then set on rods) | |||
#PEI was already attached. Should be left for the builder. | |||
#End stop holders need modification, Both holes do not fit - one hole only is glued. Had to scrape mid of endstop to make it fit (missed this in Sara's build evaluation) | |||
#Wire of power supply needs to point sideways, not down (same issue in Sara's) | |||
=Links= | |||
*[[Prepping for 1st Kit Building]] |
Latest revision as of 16:57, 20 November 2018
Build Space
Make a copy of:
Main Certification Spreadsheet
make a copy of Sara's - https://docs.google.com/spreadsheets/d/1k1qLG1_LydebeziBzCr1ePvJ2fdkDO85xidjKrGdd9I/edit#gid=0
Electronics Certification
make copy of https://docs.google.com/presentation/d/1tuqGoRbD_J-1NZOyky5YsDny67ybINcYIUi9IxU4gtc/edit#slide=id.g4071900322_0_32
Kit Inventory
From 3D_Printer_Inventory::Alex:
Evaluation
Kit build went well. There were missing parts (not printed) that were substituted (first picture in video above), and some issues:
- LCD did not work
- LCD location on control panel was in the way of the cable chain due to old documentation (main documentation has been since updated)
- Printed carriages needed cleaning
- There was an additional hole in the front frame piece which marcin mistook for a Z axis hole, only to find out that it did not have the opposing hole, and this resulted in a build error. I had to redrill a hole for the second Z.
- Frame had old epoxy on it. Had to clean it with a knife and grinder.
- It turns out that 8 mm shafts were tight. I replaced X and Y shafts with 5/16" shafts. This issue may depend on filament and printer - for the printed part quality. I left the Z axes at 8 mm - but needed extra glide on X and Y for speed.
- Back bottom Z axis hole was too far down for the Z axis to fit - had to redrill the hole higher.
- Two bed standoff nuts did not fit on 8 mm rods - used other nuts
- Wire on the Z probe connector - excessively long, had to wrap up many more times in the final wiring. Works, but took more time.
- Control panel - MOSFET too close to USB plug - needs to go a little to the right, and need to correct instructions. Also, needs 3rd mounting hole on MOSFET so the MOSFET doesn't slouch forward.
- Spool holder pieces had to be reamed out (heated then set on rods)
- PEI was already attached. Should be left for the builder.
- End stop holders need modification, Both holes do not fit - one hole only is glued. Had to scrape mid of endstop to make it fit (missed this in Sara's build evaluation)
- Wire of power supply needs to point sideways, not down (same issue in Sara's)