|
|
| (41 intermediate revisions by 3 users not shown) |
| Line 1: |
Line 1: |
| =The Embassy Elf (MBC UELVE)= | | https://m.youtube.com/watch?v=S1E8SQde5rk |
|
| |
|
| Intended as a lightweight proof of concept MBC (Myth Buster Car) for further development of additional larger (and smaller) hybrid and tribrid electric vehicles such as solar vehicles.
| | = Basics = |
|
| |
|
| Acronym decoding:
| | * A vehicle design utilising [[Fiber Composite Reinforced Pipes]] or |
| | bamboo poles or PVC pipes (what is available). The design is focussed on efficiency. |
| | * The acronyms stand for Ultra-Efficient Libre Vehicles for Everyone - Myth Busters Car |
| | * Is a prototype for further iterations of vehicles using similar methods for various other vehicle types, as well as structures such as furniture, sheds and semi-permanent buildings. |
|
| |
|
| * UELVEs: Ultra-Efficient Libre Vehicles for Everyone.
| | Versions: |
| * MBC: the Embassy, or the "MythBusters Car" (get it?), in honour of their discovery that a golf-ball texture on a car bodypanels significantly improves fuel economy. https://www.youtube.com/watch?v=VUiGhyHC-1A
| |
|
| |
|
| =Frame Concept=
| | * [[UELVE MBC/v0.0]] (concept, initial CAD, scale model) |
| | * [[UELVE MBC/v0.1]] (build underway) |
|
| |
|
| | = Images = |
| [[File:uelves_mbc.jpg|600px]] | | [[File:uelves_mbc.jpg|600px]] |
|
| |
|
| Blue pipes are 1m measure sticks. Note that the body takes whatever form we would like.
| | =See Also= |
| | |
| = Specifications =
| |
| | |
| {{Hint|Holy shit.}}
| |
| * 4 wheels using mountain bike 19in rims and 2.75/19 motorcycle tires (26in outer diameter)
| |
| * 100kg weight (full, complete vehicle)
| |
| * 2 occupants
| |
| * Twin 3-5kW Axial Flux BLDC chain-driven motors (no gearbox needed)
| |
| * 1.1 x 1.5 x 3.4 metre dimensions with an "airbox" down the centre
| |
| * Only a 1.1 m^2 front surface area (due to the "air tunnel")
| |
| * 0-60mph in under four seconds (Sur-Ron "3" kW Motors can be pushed to 13kW for short durations, and there's two of them)
| |
| * over 200mpg at 55mph due to low weight, low rolling resistance, reduced surface area and low drag coefficient.
| |
| * capable of driving up a 50% gradient at around 25mph with 2 occupants.
| |
| | |
| ==Notes==
| |
| | |
| * While world records are held for under 3 seconds, under 4 seconds is close to world records. [https://en.wikipedia.org/wiki/List_of_fastest_production_cars_by_acceleration]. We can emphasize here that for "acceleration per horsepower", ours here is probably a world record. Luke - have you done the numbers on this one?
| |
| * with the simulator i wrote a few years ago, yes. link at bottom of page. it's the reduced weight, reduced drag coefficient and the SurRon axial flux motors which can do 13KW for short bursts that do it. the world record is an MIT team EV with 4 hub motors. 0 to 60 in 1.9 seconds. in the slo mo the walls of the tires actually buckle under the acceleration.
| |
| | |
| Correction: that MIT team has been beaten by AMZ, who officially managed 0 to 60 (100km/h) in 1.513 seconds
| |
| | |
| {{YoutubePopup|n2XiCYA3C9s}}
| |
| | |
| =Design Concept=
| |
| | |
| * Use downhill mountain-bike parts that have been proven to be light, strong and effective up to a 50kg weight with an 80kg load, thanks to the Sur-Ron Electric Bike.
| |
| * Use twin Sur-Ron direct-drive 3-5kW Axial Flux electric motors
| |
| * Use twin ASI BAC4000 BLDC Controllers (or VESC Vedder BLDC Controllers http://vedder.se/2015/01/vesc-open-source-esc/)
| |
| * Outer skin using the GABoats technique (Geodesic Aerolite Boats) - http://gaboats.com
| |
| * Inner frame using 3D-printed fibre-reinforced "nodes" connecting continuous-fibre-reinforced pipes on a [[Fibre_Reinforced_Pipe_3D_Printer]] or getting carbon-fibre, hemp-reinforced tubes (or even Bamboo), based on the Divergent 3D "Blade" car manufacturing concept https://www.youtube.com/watch?v=vPv7PwS50OE
| |
| * Epoxy-soaked cloth "wrapping" carried out on joints, if necessary, using the Calfee Design Bamboo bike technique. https://calfeedesign.com/what-is-in-calfee-diy-kits/
| |
| * Swappable Modular batteries using the [[Open_Source_Battery_Pack]]
| |
| | |
| =Source Code=
| |
| | |
| * git clone http://lkcl.net/vehicle_3d/.git
| |
| | |
| = BOM =
| |
| | |
| estimated, todo steering and suspension, estimated total under USD 4000 excluding tools and batteries.
| |
| | |
| * 3D printed 15mm x 2mm kevlar/hemp continuous reinforced pipes (250 metres)
| |
| * 3D printed "nodes" (120)
| |
| * Kevlar twine (see gaboats)
| |
| * Dacron (see gaboats)
| |
| * QTY 2 Shimano Saint M820 mountain bike hydraulic brake sets (2 front, 2 rear)
| |
| * QTY 4 19in diameter downhill mountain bike wheels
| |
| * QTY 4 2.75/19in Shinko "Goldenboy" tires
| |
| * QTY 4 Fox DHX2 rear suspension sets with orange spring
| |
| * QTY 2 Sur-Ron 3kW BLDC Axial Flux Motors
| |
| * QTY 2 Sur-Ron rear swingarm (or structurally strong 3D printed equivalent, TBD)
| |
| * QTY 2 20kW 3 phase BLDC Motor Controllers (Vedder VESC)
| |
| * 6 guage wire (appx 5 metres)
| |
| * QTY 15 (appx) Open Source Battery Packs per kWh
| |
| * Bus Bars connecting packs together
| |
| * Bearings (lots)
| |
| | |
| =TODO=
| |
| | |
| * Simulation (playable game) using ODE (Open Dynamic Engine) which will be cool and also test real-world joint strength and drivability. See Hackrod.
| |
| | |
| =Notes from Julia log=
| |
| | |
| https://wiki.opensourceecology.org/wiki/ImplicitCAD#Julia
| |
| | |
| recycling fibre reinforced plastic, fibres get shorter and shorter. (solution: add more back in?)
| |
| | |
| carbon fibre eco hostile (not going to use carbon fibre, use hemp fibre or wood fibre, see Da Ai Technology in taiwan)
| |
| | |
| use detroit technique: 3 pieces, front middle and back. matches with what i suggested, given that big printer is aiming for 4x4x8 ft. roof and floor will probably need to be separate in this design (so, 4 pieces)
| |
| | |
| =Material Strength Test=
| |
| | |
| the logical reasoning behind this test is to find out if, with fibre-reinforced plastic, the layer adhesion affects strength of the part under load when bolts are screwed directly into it.
| |
| | |
| #two M10 1.5mm pitch bolts (or close: 3/8 with 1/16in pitch)
| |
| #a 30 x 30 x 30mm cube made of fibre reinforced plastic with a smooth cylinder hole down the middle about 7 or 7.5mm diameter
| |
| #print that using 100% infill, fibre reinforced plastic, with a minimum 0.8mm nozzle, preferably 1.2mm, with the hole pointing UPRIGHT.
| |
| #screw the two M10 bolts in, using the thread to "tap" the holes, making them meet in the middle
| |
| #hang it from a bench by 1 bolt and keep putting weights on it until it breaks.
| |
| | |
| i need to know, how much weight it took. it might be a lot, before the cube breaks or the threads strip.
| |
| | |
| the next test is printing it where the hole is horizontal.
| |
| | |
| the "more advanced" version of that is for the hole to be at 45 degrees through the cube, i.e to test the effect of diagonal layers.
| |
| | |
| == questions ==
| |
| | |
| # what kind of fibre plastic? answer: don't know enough to say. ideally several materials should be tested and the results fully documented.
| |
| # what diameter hole? assuming using the bolt as self-tapping, an M10 bolt with 1.5mm pitch has around a 1.5 mm inset, therefore 10mmm minus 1.5x2 equals 7mm, so between 7 and 7.5mm seems sensible to try. bottom line: if it cracks on insertion, the hole was too small!
| |
| # how should the weights be hung? doesn't matter as long as side-twisting is avoided (we are not testing shearing or twisting, here, yet, just pulling). strong rope tied or clamped to both bolts, one end fixed to a table, the other has weights attached, it doesn't matter. doesn't have to be sophisticated, here.
| |
| | |
| == Expected Issues ==
| |
| | |
| One key issue to watch out for is the block cracking as the M10 bolt is screwed in. Normally, a tap/die would be considered, here.
| |
| | |
| The problem is that when using 1.2mm nozzles, it is extremely unlikely to be able to 3D print a matching 1.5mm thread for the bolt to fit in, therefore tapping the hole is the next option, and seeing if the bolt itself will achieve that is logical to attempt.
| |
| | |
| One alternative ie to look for very coarse threaded M10 bolts, or even trapeoizoidal bar, or, if this really doesn't work, some alternative lock mechanism, or a much larger diameter hole and use epoxy glue. of course, epoxy glue you are never going to be able to remove the bolt.
| |
| | |
| [[File:MBC_strength_test.jpg|600px]]
| |
| | |
| = Videos =
| |
| | |
| {{YoutubePopup|myu6vBy0ASs|big}}
| |
| | |
| = See Also = | |
| | |
| * [[Two Wheeled Velomobile]] | | * [[Two Wheeled Velomobile]] |
| * [[Velomobile]] | | * [[Velomobile]] |
| Line 127: |
Line 22: |
|
| |
|
| =Useful Links= | | =Useful Links= |
| | | *[http://lkcl.net/ev/vehicle_simulator/output/Simulator.html Simple Vehicle Simulator including gears, gear-changes, wind-resistance, rolling-resistance, gradients etc. ] |
| * Simple Vehicle Simulator including gears, gear-changes, wind-resistance, rolling-resistance, gradients etc. http://lkcl.net/ev/vehicle_simulator/output/Simulator.html | | * https://ec.europa.eu/info/funding-tenders/opportunities/portal/screen/opportunities/topic-details/horizon-cl5-2023-d5-01-03 |
