Heat Pump Installation: Difference between revisions
Jump to navigation
Jump to search
(→Links) |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Online Instructionals= | =Online Instructionals= | ||
*'''{{Check}}Complete video including flex pvc on wires, bending, cutting with tubing cutter, no line bender needed if you route coolant lines | *'''{{Check}}Complete video including flex pvc on wires, bending, cutting with tubing cutter, no line bender needed if you route coolant lines effectively. [https://youtu.be/JQkth-AM5CE] | ||
=SH4 Heat Pump Build Instructions= | =SH4 Heat Pump Build Instructions= | ||
<html> | <html> <iframe src="https://docs.google.com/presentation/d/e/2PACX-1vTwIraS-Hf0p0QtuWxC2_Yf3zAZRvCr-_qqT3XDB7Zvr5jLQMd9YMkM7Z__0QhMivVNSdJ8lt7rbBr1/embed?start=false&loop=false&delayms=3000#slide=id.g239a841a92e_0_44" frameborder="0" width="480" height="389" allowfullscreen="true" mozallowfullscreen="true" webkitallowfullscreen="true"></iframe> </html> | ||
[https://docs.google.com/presentation/d/1YF44L9WZ75y9LLAr8AwxbeC-K__OKJVt7FZzvzeQQ6Y/edit#slide=id.g239a841a92e_0_44 edit] | [https://docs.google.com/presentation/d/1YF44L9WZ75y9LLAr8AwxbeC-K__OKJVt7FZzvzeQQ6Y/edit#slide=id.g239a841a92e_0_44 edit] | ||
=Heat Pump Line Evacuation and Refrigerant Release= | |||
This is doc taken from SH4-4 and Sh4-5 build docs and put into one document: | |||
[[Heat Pump Line Evacuation and Refrigerant Release]] | |||
=OSE Installs= | =OSE Installs= | ||
| Line 21: | Line 27: | ||
=Resources= | =Resources= | ||
*Good pdf - [[File:heatpumpinstall.pdf]] | *Good pdf overview of process - [[File:heatpumpinstall.pdf]] | ||
=Links= | =Links= | ||
*[[Heat Pump]] | *[[Heat Pump]] | ||
*[[Senville Aura]] | *[[Senville Aura]] | ||
*Heat pumps - initial concpepts doc - [https://docs.google.com/presentation/d/15mYKFucL57P8U_dvaXIhAW36M7y_NE7EAeoDSx3XvC0/edit?slide=id.ga2b61afa46_2_1#slide=id.ga2b61afa46_2_1] | |||
[[Category: HVAC]] [[Category: Instructions]] [[Category: Instructionals]] | [[Category: HVAC]] [[Category: Instructions]] [[Category: Instructionals]] | ||
Latest revision as of 03:52, 8 February 2026
Online Instructionals
Complete video including flex pvc on wires, bending, cutting with tubing cutter, no line bender needed if you route coolant lines effectively. [1]
SH4 Heat Pump Build Instructions
Heat Pump Line Evacuation and Refrigerant Release
This is doc taken from SH4-4 and Sh4-5 build docs and put into one document:
Heat Pump Line Evacuation and Refrigerant Release
OSE Installs
- Proper install means you cut the line set to the correct length, otherwise you would coil them up (oil sump issues) or run them extra length just to use up the available length (unsightly and time consuming) [2]. If you cut lines, you may need to add or remove precharged refrigerant.
- Outdoor unit may be higher or lower than indoor unit [3]
- Floor-mounted unit mounted high on wall? Yes - see Answered Questions by user Dan Mueller [4]
Resources
- Good pdf overview of process - File:Heatpumpinstall.pdf
Links
- Heat Pump
- Senville Aura
- Heat pumps - initial concpepts doc - [5]