Mike Hill Modular Wheel Units Order

Introduction

The wheel unit parts prior to the addendum make:

• one set of 3" shaft wheel units - for trucktor
• one set of 1-7/8" shaft wheel units - for microtrac or bulldozer
• One set of gear reduction units - for Bulldozer. Bulldozer uses 1-7/8" drive and 3" gear reduction.
• 2 idler wheels for Microtrac

Parts

edit

92 parts total - Complete DXFs here - File:Hillparts.zip. Quantities of specific part below:

• [4] Part 1 - File:Wheel Mounts Part 1.dxf
• [6] Part 2 - File:Wheel Mounts Part 2.dxf
• [4] Part 3 - File:Wheel Mounts Part 3.dxf
• [6] Part 4 - File:Wheel Mounts Part 4.dxf
• [8] Part 5 - File:Wheel Mounts Part 5.dxf
• [2] Part 6 - File:Wheel Mounts Part 6.dxf
• [8] Part 7 - File:Wheel Mounts Part 7.dxf
• [12] Part 8 - File:Wheel Mounts Part 8.dxf
• [2] Part 9 - File:Wheel Mounts Part 9.dxf
• [8] Part 10 - File:Wheel mounts Part 10.dxf
• [8] Part 11 - File:Wheel Mounts Part 11.dxf

For geardown from here on, not shown above, see James_Log#Tue_Jun_18.2C_2013) - -

• [4] Part 12 - File:Wheel Mounts Part 12.dxf
• [4] Part 13 - File:Wheel Mounts Part 13.dxf
• [4] Part 14 - File:Wheel Mounts Part 14.dxf
• [4] Part 15 - File:Wheel Mounts Part 15.dxf
• [4] Part 16 - File:Wheel Mounts Part 16.dxf
• [4] Part 17 - File:Wheel Mounts Part 17.dxf

Parts Addendum

File:Hillparts2.zip - parts 18-32. 100 parts more.

• [4] Part 18 - Sprocket - File:45T325bore1by8cut.dxf -
• [8] Part 19 - Hub Plate - File:3hubplate.dxf -
• [4] Part 20 - Microtrac Hub - File:Wheel Hub for MicroTrac.dxf -
• [4] Part 21 - Trucktor Motor Interface Plate - File:Trucktorinterface.dxf -
• [8] Part 22 - Bobcat Standard Quick Attach Standard - File:Bobcatstandard.dxf -
• [7] Part 23 - Dozer Rib 1 - File:Drib1.dxf -
• [7] Part 24 - Dozer Rib 2 - File:Drib2.dxf -
• [4] Part 25 - Pivot Holder 1 - File:Holder1.dxf -
• [4] Part 26 - Pivot Holder 2 - File:Holder2.dxf -
• [2] Part 27 - Pivot - File:Dpivot.dxf -
• [4] Part 28 - Spacer - File:Pspacer.dxf -
• [4] Part 29 - Ear - File:Pear.dxf -
• [8] Part 30 - Ironworker Blade Holder - File:Bladeholder.dxf -
• [16] Part 31 - Small Bonding Plate - File:Stocksmallbond.dxf -
• [16] Part 32 - Medium Bonding Plate - File:Stockmedbond.dxf -

Summary

(note: appears there are 4 too many of the 3" hole plates for geardown)

File:Thisorder.dxf

Images

• [4] Part 1 -
• [8] Part 2 -
• [4] Part 3 -
• [8] Part 4 -
• [10] Part 5 -
• [2] Part 6 -
• [10] Part 7 -
• [14] Part 8 -
• [2] Part 9 -
• [10] Part 10 -
• [10] Part 11 -