Industrial Robot/Manufacturing Instructions: Difference between revisions
Jump to navigation
Jump to search
| Line 16: | Line 16: | ||
**Drill 3 holes in each bar (redone image TBD) | **Drill 3 holes in each bar (redone image TBD) | ||
[[ | [[Media:Pillar.jpg]] | ||
*[1] Plate | *[1] Plate | ||
**Drill 13 holes (redone image) | **Drill 13 holes (redone image) | ||
[[ | [[Media:IROverplate.jpg]] | ||
*[12] Bolts | *[12] Bolts | ||
| Line 27: | Line 27: | ||
*[4] Bolts | *[4] Bolts | ||
===Main Arm=== | ===Main Arm=== | ||
Revision as of 09:36, 12 August 2011
| Industrial Robot | ||
|---|---|---|
| Home | Research & Development | Bill of Materials | Manufacturing Instructions | User's Manual | User Reviews | 
| |
Open Section Fabrication and Assembly
Structure
Foundation
- [2] Main tubes
- [2] Support tubes
- [4] Raising Bars
- Drill 3 holes in each bar (redone image TBD)
- [1] Plate
- Drill 13 holes (redone image)
- [12] Bolts
- [4] Bolts
- [4] Bolts
Main Arm
- [1] Bar
- Drill 18 holes
- [8] Bolts
- [8] Bolts
Forearm
- Perpendicular Plate
- Drill 9 holes
- Weld to tube
- Tube
- Parallel Plate
- Drill 9 holes
- Weld to tube
- [8] Bolts
- [8] Bolts
Gearbox 1,2
- [2] Hydraulic Motor
- [1] Angle
- Drill
- [2] Input Plate
- Drill
- Note: Location of mounting holes for hydraulic motor unknown
- [4] Side Plate
- Drill
- [2] Cover Plates
- Drill
- [4] Outer Race Plate
- Torch
- Drill
- [2] Round Bar
- Grind
- Drill
- Tap
- [4] Inner Race
- Turn
- Drill
- [2] Output Hub
- Turn
- Drill
- Broach
- [2] Support Hub
- Turn
- Drill
- Broach
- [1] Loose Ball Bearings
- [12] Side Plate Bolts
- [12] Side Plate Nuts
- [4] Cover Plate Bolts
- [4] Cover Plate Nuts
- [4] O-ring Seal
- [4] Output Shaft Bolts
- [4] Lube Bolts
- [2] Input Gear
- [2] Output Gear
- [2] Key
Gearbox 3,4
Forearm Angle
- As shown below
Wrist Angle
- As shown below
Gearbox 3,4,5,6 Input Plate
- Note: Location of mounting holes for hydraulic motor unknown
Gearbox 3,4,5,6 Side Plates
Gearbox 3,4,5,6 Cover Plates
Gearbox 3,4,5,6 Outer Race Plate
Gearbox 3,4,5,6 Output Hub
*incorrect picture
Gearbox 3,4,5,6 Output Shaft
- Keyed
Gearbox 3,4,5,6 Inner Race
Encoder Mount
Encoder Mount Support Angle
Encoder Mount Main Angle
Encoder Mount Coupling
Stepper Mount
Stepper Motor Mount Angle
Stepper Motor Mount Plate
Shaft Bar
- As shown below, repeat for a total of 6 bars
Assemble Components
Assemble Gearboxes
Assemble Industrial Robot
- As shown below
Assemble Stepper Motor Mount
- As shown below, repeat for a total of 6 mounts
Connect Components
Hydraulic Connections
- 2 Axes Hydraulic Circuit
- Hydraulic Circuit
Electronic Connections
- As shown below
