Industrial Robot Bill of Materials
Jump to navigation
Jump to search
| Industrial Robot | ||
|---|---|---|
| Home | Research & Development | Bill of Materials | Manufacturing Instructions | User's Manual | User Reviews | 
| |
- Note: Major Changes to be applied along with master diagram.
- This bill of materials is a developmental version.
| PART NAME | NUMBER NEEDED | PURPOSE | COST | SUGGESTED SOURCE |
|---|---|---|---|---|
| Foundation Underplate | 1 | Ground contact mount for industrial robot (15" by 15" by 0.25" A36 steel plate) | est. under 130 | |
| Foundation Underplate Bolt | 4 | Fastener piece for foundation underplate to support (stainless steel 18-8, 1/2”-13 diameter and threads per inch, 3" length, hex bolt) | est. under 6 | |
| Foundation Underplate Washer | 4 | Fastener piece for foundation underplate to support (stainless steel 18-8, 1/2” inner diameter washer) | est. under 1 | |
| Foundation Underplate Nut | 4 | Fastener piece for foundation underplate to support (stainless steel 18-8, 1/2”-13 diameter and threads per inch, hex nut) | est under 2 | |
| MIG Welding Consumables | Enough for welding the 4 pillars onto the foundation underplate and 2 hubs onto the tube | Materials for welding the foundation pillars onto the foundation underplate | guess under 10 | |
| Foundation Pillar | 4 | Supporting frame between foundation plates(2” by 2” by 10”, A36 steel square bar) | est under 100 | |
| Foundation Angle | 4 | Connector piece between foundation pillars and foundation overplate (4” width A by 2” width B by 2” length, A36 steel angle, 0.5” thickness) | est under 6 | |
| Foundation Angle Bolt | 12 | Fastener piece between foundation pillars and foundation overplate (stainless steel 18-8, 1/2”-13 diameter and threads per inch, 3” length, hex bolt) | est under 5 | |
| Foundation Angle Washer | 12 | Fastener piece between foundation pillars and foundation overplate (stainless steel 18-8, 1/2” inner diameter washer) | est under 1 | |
| Foundation Angle Nut | 12 | Fastener piece between foundation pillars and foundation overplate (stainless steel 18-8, 1/2”-13 diameter and threads per inch, hex nut) | est under 2 | |
| Foundation Overplate | 1 | Mid-air mount for industrial robot (11” by 11” by 0.25” A36 steel plate) | est under 90 | |
| Joint 1 Gearbox | 1 | Enables rotation of baseplate relative to foundation overplate and insertion of motor shaft for rotation control | guess under 100 | |
| Joint 1 Gearbox Bolt | 10? | Fastener piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 15 | |
| Joint 1 Gearbox Washer | 10? | Fastener piece (stainless steel 18-8, x inner diameter washer) | guess under 2 | |
| Joint 1 Gearbox Nut | 10? | Fastener piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 4 | |
| Joint 1 Hydraulic Motor | 1 | Rotates base of industrial robot | est under 150 | surpluscenter |
| Joint 1 Motor Bolt | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 6 | |
| Joint 1 Motor Washer | 4? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 1 | |
| Joint 1 Motor Nut | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 1 | |
| Base Angle | 1 | Base for industrial robot on top of foundation overplate (8” width A by 8” width B by 8” length A36 steel angle, 1” thickness) | est under 90 | |
| Joint 2 Hydraulic Motor | 1 | Tilts main arm of industrial robot from base | es under 150 | surpluscenter |
| Joint 2 Hydraulic Motor Bolt | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 6 | |
| Joint 2 Hydraulic Motor Washer | 4? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 1 | |
| Joint 2 Hydraulic Motor Nut | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 1 | |
| Joint 2 Gearbox | 1 | Enables tilting of main arm relative to baseplate and control through shaft | guess under 100 | |
| Joint 2 Gearbox Bolt | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 15 | |
| Joint 2 Gearbox Washer | 10? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 2 | |
| Joint 2 Gearbox Nut | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 4 | |
| Main Arm | 1 | Frame piece from baseplate to elbow (24“ by 6” by 2” A36 steel bar) | est under 150 | |
| Joint 3 Gearbox | 1 | Enables tilting of forearm relative to main arm, and control through shaft | guess under 100 | |
| Joint 3 Gearbox Bolt | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 15 | |
| Joint 3 Gearbox Washer | 10? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 2 | |
| Joint 3 Gearbox Nut | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 4 | |
| Joint 3 Hydraulic Motor | 1 | Tilts forearm of industrial robot from main arm | est under 150 | surpluscenter |
| Joint 3 Hydraulic Motor Bolt | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 6 | |
| Joint 3 Hydraulic Motor Washer | 4? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 1 | |
| Joint 3 Hydraulic Motor Nut | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 1 | |
| Joint 4 Hydraulic Motor | 1 | Rotates wrist of industrial robot from forearm | est under 150 | surpluscenter |
| Joint 4 Hydraulic Motor Bolt | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 6 | |
| Joint 4 Hydraulic Motor Washer | 4? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 1 | |
| Joint 4 Hydraulic Motor Nut | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 1 | |
| Joint 4 Gearbox | 1 | Enables rotation of wrist relative to forearm and control through shaft | guess under 100 | |
| Joint 4 Gearbox Bolt | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 15 | |
| Joint 4 Gearbox Washer | 10? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 1 | |
| Joint 4 Gearbox Nut | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 2 | |
| Forearm Angle | 1 | For mounting of joint 4 hydraulic motor (8” width A by 8” width B by 12” length steel L-piece, 1” thickness) | est under 150 | |
| Forearm Angle Bolt | 4 | Fastener Piece (stainless steel 18-8, 1/2”-13 diameter and threads per inch, z length, hex bolt) | est under 6 | |
| Forearm Angle Washer | 4 | Fastener Piece (stainless steel 18-8, 1/2” inner diameter washer) | est under 1 | |
| Forearm Angle Nut | 4 | Fastener Piece (stainless steel 18-8, 1/2”-13 diameter and threads per inch, hex nut) | est under 2 | |
| Forearm Hub 1 | 1 | Square plate at one end of forearm (8” by 8” by 0.5” A36 steel plate) | guess under 50 | |
| Forearm | 1 | Tube connecting elbow to wrist (18” length by 6” diameter by 0.5” thickness A36 steel tube) | guess under 150 | |
| Forearm Hub 2 | 1 | Square plate at one end of forearm (8” by 8” by 0.5” A36 steel plate) | guess under 50 | |
| Wrist Angle | 1 | For mounting of joint 5 hydraulic motor (8” width A by 8” width B by 8” length steel angle, 1” thickness) | est under 90 | |
| Wrist Angle Bolt | 4 | Fastener Piece (1/2”-13, 3”, 18-8 Stainless Steel hex bolt) | est under 5 | |
| Wrist Angle Nut | 4 | Fastener Piece (1/2”-13, 18-8 Stainless Steel hex nut) | est under 1 | |
| Wrist Angle Washer | 4 | Fastener Piece (1/2”, 18-8 Stainless Steel washer) | est under 1 | |
| Joint 5 Hydraulic Motor | 1 | Tilts wrist of industrial robot | est under 150 | surpluscenter |
| Joint 5 Hydraulic Motor Bolt | 4? | Fastener piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 6 | |
| Joint 5 Hydraulic Motor Washer | 4? | Fastener piece (stainless steel 18-8, x inner diameter washer) | guess under 1 | |
| Joint 5 Hydraulic Motor Nut | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 1 | |
| Joint 5 Gearbox | 1 | Enables tilting of wrist relative to forearm and control through shaft | guess under 100 | |
| Joint 5 Gearbox Bolt | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 15 | |
| Joint 5 Gearbox Washer | 10? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 2 | |
| Joint 5 Gearbox Nut | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 2 | |
| Joint 6 Angle | 1 | For mounting of joint 6 hydraulic motor (8”A by 8”B by 8”Length L-piece, 0.5” thickness) | est under 90 | |
| Joint 6 Angle Bolt | 4 | Fastener Piece (stainless steel 18-8, 1/2”-13” diameter and threads per inch, z length, hex bolt) | est under 6 | |
| Joint 6 Angle Washer | 4 | Fastener Piece (stainless steel 18-8, 1/2” inner diameter washer) | est under 2 | |
| Joint 6 Angle Nut | 4 | Fastener Piece (stainless steel 18-8, 1/2”-13 diameter and threads per inch, hex nut) | est under 2 | |
| Joint 6 Hydraulic Motor | 1 | Rotates end-effector of industrial robot | est under 150 | surpluscenter |
| Joint 6 Hydraulic Motor Bolt | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 6 | |
| Joint 6 Hydraulic Motor Washer | 4? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 2 | |
| Joint 6 Hydraulic Motor Nut | 4? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 2 | |
| Joint 6 Gearbox | 1 | Enables rotation of end effector relative to wrist and control through shaft | guess under 100 | |
| Joint 6 Gearbox Bolt | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, z length, hex bolt) | guess under 15 | |
| Joint 6 Gearbox Washer | 10? | Fastener Piece (stainless steel 18-8, x inner diameter washer) | guess under 2 | |
| Joint 6 Gearbox nut | 10? | Fastener Piece (stainless steel 18-8, x-y diameter and threads per inch, hex nut) | guess under 2 | |
| Powercube | 1? | As prime mover-connected pump and reservoir for hydraulic system | P | |
| Primary 4-way Pipe | 1 | For tubing connection to: Pump, Secondary 4-way Pipe, Tertiary 4-way Pipe, Pressure Relief Valve | guess under 20 | |
| Pump to Primary 4-way Pipe Hose | 1 | Hydraulic connector (x max pressure, y length, z dia) | guess under 20 | |
| Pressure Relief Valve | 1 | For maintaining continuity of flow when flow to all hydraulic motors is cut | est under 50 | surpluscentre |
| Primary 4-way Pipe to Pressure Relief Valve Hose | 1 | Hydraulic connector (x max pressure, y length, z dia) | guess under 20 | |
| Pressure Relief Valve to Tank Hose | 1 | Hydraulic connector (x max pressure, y length, z dia) | guess under 20 | |
| Secondary 4-way Pipe | 1 | For tubing connection to: Primary 4-way Pipe, Joint 1 Needle Valve, Joint 2 Needle Valve, Joint 3 Needle Valve | guess under 20 | |
| Primary 4-way Pipe to Secondary 4-way Pipe Hose | 1 | Hydraulic connector (x pressure, y length, z dia) | guess under 20 | |
| Tertiary 4-way Pipe | 1 | For tubing connection to: Primary 4-way Pipe, Joint 4 Needle Valve, Joint 5 Needle Valve, Joint 6 Needle Valve | guess under 20 | |
| Primary 4-way Pipe to Tertiary 4-way Pipe Hose | 1 | Hydraulic connector (x pressure, y length, z dia) | guess under 20 | |
| Joint 1 Needle Valve | 1 | Flow control for joint 1 hydraulic motor | est under 43 | |
| Joint 2 Needle Valve | 1 | Flow control for joint 2 hydraulic motor | est under 43 | |
| Joint 3 Needle Valve | 1 | Flow control for joint 3 hydraulic motor | est under 43 | |
| Secondary 4-way pipe to Joint 1 Needle Valve Hose | 1 | Hydraulic Connector | guess under 20 | |
| Secondary 4-way pipe to Joint 2 Needle Valve Hose | 1 | Hydraulic Connector | guess under 20 | |
| Secondary 4-way pipe to Joint 3 Needle Valve Hose | 1 | Hydraulic Connector | guess under 20 | |
| Joint 4 Needle Valve | 1 | Flow control for joint 4 hydraulic motor | est under 43 | surpluscentre |
| Joint 5 Needle Valve | 1 | Flow control for joint 5 hydraulic motor | est under 43 | surpluscentre |
| Joint 6 Needle Valve | 1 | Flow control for joint 6 hydraulic motor | est under 43 | surpluscentre |
| Tertiary 4-way Pipe to Joint 4 Needle Valve Hose | 1 | Hydraulic Connector | guess under 20 | |
| Tertiary 4-way Pipe to Joint 5 Needle Valve Hose | 1 | Hydraulic Connector | guess under 20 | |
| Tertiary 4-way Pipe to Joint 6 Needle Valve Hose | 1 | Hydraulic Connector | guess under 20 | |
| Joint 1 Solenoid Valve | 1 | 2?-position directional control for joint 1 hydraulic motor | est under 50 | surpluscentre |
| Joint 2 Solenoid Valve | 1 | 2?-position directional control for joint 2 hydraulic motor | est under 50 | surpluscentre |
| Joint 3 Solenoid Valve | 1 | 2?-position directional control for joint 3 hydraulic motor | est under 50 | surpluscentre |
| Joint 4 Solenoid Valve | 1 | 2?-position directional control for joint 4 hydraulic motor | est under 50 | surpluscentre |
| Joint 5 Solenoid Valve | 1 | 2?-position directional control for joint 5 hydraulic motor | est under 50 | surpluscentre |
| Joint 6 Solenoid Valve | 1 | 2?-position directional control for joint 6 hydraulic motor | est under 50 | surpluscentre |
| Joint 1 Needle Valve to Solenoid Valve Hose | 1 | Hydraulic connector | guess under 20 | |
| Joint 2 Needle Valve to Solenoid Valve Hose | 1 | Hydraulic connector | guess under 20 | |
| Joint 3 Needle Valve to Solenoid Valve Hose | 1 | Hydraulic connector | guess under 20 | |
| Joint 4 Needle Valve to Solenoid Valve Hose | 1 | Hydraulic connector | guess under 20 | |
| Joint 5 Needle Valve to Solenoid Valve Hose | 1 | Hydraulic connector | guess under 20 | |
| Joint 6 Needle Valve to Solenoid Valve Hose | 1 | Hydraulic connector | guess under 20 | |
| Joint 1 Solenoid Valve to Tank Hose | 1 | Hydraulic Connector | guess under 20 | |
| Joint 2 Solenoid Valve to Tank Hose | 1 | Hydraulic Connector | guess under 20 | |
| Joint 3 Solenoid Valve to Tank Hose | 1 | Hydraulic Connector | guess under 20 | |
| Joint 4 Solenoid Valve to Tank Hose | 1 | Hydraulic Connector | guess under 20 | |
| Joint 5 Solenoid Valve to Tank Hose | 1 | Hydraulic Connector | guess under 20 | |
| Joint 6 Solenoid Valve to Tank Hose | 1 | Hydraulic Connector | guess under 20 | |
| Joint 1 Solenoid Valve to Hydraulic Motor Hose | 2 | Hydraulic Connector | guess under 20 | |
| Joint 2 Solenoid Valve to Hydraulic Motor Hose | 2 | Hydraulic Connector | guess under 20 | |
| Joint 3 Solenoid Valve to Hydraulic Motor Hose | 2 | Hydraulic Connector | guess under 20 | |
| Joint 4 Solenoid Valve to Hydraulic Motor Hose | 2 | Hydraulic Connector | guess under 20 | |
| Joint 5 Solenoid Valve to Hydraulic Motor Hose | 2 | Hydraulic Connector | guess under 20 | |
| Joint 6 Solenoid Valve to Hydraulic Motor Tubing | 2 | Hydraulic Connector | guess under 20 | |
| DC Power Supply | 1 | To power various electronic components | guess under 100 | |
| Power Supply to Stepper Motor Driver Wires | Electric Connector for 6 channels | guess under 10 | ||
| Power Supply to Solenoid Driver Wires | Electric Connector for 6 channels | guess under 10 | ||
| Microcontroller | 1 | To receive computer signals and shaft encoder signals; to command stepper motor drivers and solenoid drivers (ex. arduino mega 2560) | est under 60 | |
| Stepper Motor Driver | (6 channels total) | To receive microcontroller signals and give electric current to stepper motors for joint 1-6 needle valves | est under 60 | |
| Microcontroller to Stepper Motor Driver Wires | Electric Connector for 6 channels | guess under 10 | ||
| Stepper Motor | 6 | To allow electric operation of joint 1-6 needle valves | est under 160 | ex. Pololu |
| Stepper Motor Driver to Stepper Motor Wires | Electric Connector for 6 Motors | guess under 10 | ||
| Stepper Motor Angle | 6 | Main Bracket Component for Stepper Motor and Needle Valve ( | est under 40 | |
| Stepper Motor Hub | 6 | To connect onto stepper motors as component for bracket | guess under 20 | |
| Needle Valve Hub | 6 | To connect onto needle valve handle as component for bracket | guess under 20 | |
| Needle Valve Plate | 12 | Bracket Component to hold needle valve | guess under 20 | |
| Needle Valve Bolt | 18 | Fastener Piece | guess under 20 | |
| Solenoid Driver | (6 channels) | To receive microcontroller signals and give electric current to joint 1-6 solenoid valves (PWM Driver 1.1 from reprapwiki) | est under 26 | |
| Shaft Encoder | 6 | To measure speed of joint 1-6 shaft rotation | guess under 300 | |
| Microcontroller to Shaft Encoder Wires | Electric Connector for 6 Shaft Encoders | guess under 20 | ||
| Grand Total | Sum of guesses, informed estimates | 5013 + P |