CNC Torch Table v19.10: Difference between revisions

From Open Source Ecology
Jump to navigation Jump to search
No edit summary
No edit summary
Line 7: Line 7:
==Mechanical==
==Mechanical==
[[File:CNC_Torch_1in_idler_module.jpg|100px]][[File:torch_idler_trimmed.png|100px]][[File:front_of_idler_trimmed.png|100px]][[File:torch.png|100px]][[File:torch_tip.png|100px]][[File:torch_handle_only.png|100px]][[File:Cnc_torch_idler_v19_10.png|100px]][[File:Bearing_1in.png|100px]][[File:nema23motor.png|100px]][[File:tb6600.png|100px]][[File:idlerassy2.png|100px]][[File:1inchshaft.png|100px]][[File:EndPlug.png|100px]][[File:idler+bearing.png|100px]][[File:Cnc_torch_carriage_v19_10.png|100px]][[File:Cnc_peg_15mm_belt_v19_10.png|100px]][[File:Cnc_torch_half_carriage_v19_10.png|100px]][[File:YAxisAssembly.PNG|100px]][[File:Torch table assembly v19 10.png|100px]][[File:CNC_Torch_Tablepic.jpg|100px]][[File:igniter.png|100px]][[File:Fl_205_cut_of_solenoid.png|100px]]
[[File:CNC_Torch_1in_idler_module.jpg|100px]][[File:torch_idler_trimmed.png|100px]][[File:front_of_idler_trimmed.png|100px]][[File:torch.png|100px]][[File:torch_tip.png|100px]][[File:torch_handle_only.png|100px]][[File:Cnc_torch_idler_v19_10.png|100px]][[File:Bearing_1in.png|100px]][[File:nema23motor.png|100px]][[File:tb6600.png|100px]][[File:idlerassy2.png|100px]][[File:1inchshaft.png|100px]][[File:EndPlug.png|100px]][[File:idler+bearing.png|100px]][[File:Cnc_torch_carriage_v19_10.png|100px]][[File:Cnc_peg_15mm_belt_v19_10.png|100px]][[File:Cnc_torch_half_carriage_v19_10.png|100px]][[File:YAxisAssembly.PNG|100px]][[File:Torch table assembly v19 10.png|100px]][[File:CNC_Torch_Tablepic.jpg|100px]][[File:igniter.png|100px]][[File:Fl_205_cut_of_solenoid.png|100px]]
[[File:quarterplug.png|100px]][[File:zassembly.png|100px]]
[[File:quarterplug.png|100px]][[File:zassembly.png|100px]][[File:Idler_belt_wheel.png|100px]]


<gallery perrow=6>
<gallery perrow=6>
Line 68: Line 68:
File:quarterplug.png|1/4" Plug. <br>FreeCAD - [[File:quarterplug.stl]]
File:quarterplug.png|1/4" Plug. <br>FreeCAD - [[File:quarterplug.stl]]


File:Idler_belt_wheel.png|Idler wheel.<br>FreeCAD - [[File:Idler_belt_wheel.fcstd]]<br>STL - [[File:Idler_belt_wheel.stl]]


</gallery>
</gallery>

Revision as of 07:19, 3 December 2019

CAD 1" Universal Axis - 3 Pieces

Frame

Mechanical

CNC Torch 1in idler module.jpgTorch idler trimmed.pngFront of idler trimmed.pngTorch.pngTorch tip.pngTorch handle only.pngCnc torch idler v19 10.pngBearing 1in.pngNema23motor.pngTb6600.pngIdlerassy2.png1inchshaft.pngEndPlug.pngIdler+bearing.pngCnc torch carriage v19 10.pngCnc peg 15mm belt v19 10.pngCnc torch half carriage v19 10.pngYAxisAssembly.PNGTorch table assembly v19 10.pngCNC Torch Tablepic.jpgIgniter.pngFl 205 cut of solenoid.png Quarterplug.pngZassembly.pngIdler belt wheel.png

Electronics

12Vps.pngAuxcontrol.pngAuxcontrol2.pngAuxcontrol3.pngAuxcontrol4.pngAuxcontrol5.png

Concept

edit

Universal Controller Automation

=Concept Video Walk-Through=

BOM

  • Impco FL-205-1 valves - [9]
  • Impco Et98-52295 valves - [10]
  • Brass 90° Elbow 1/4" NPT Male to Female - [11]
  • 40 micron Inline Gas Filter - [12][13]
  • Idler Bearing - [14]
  • Spring steel - 0.049" - [15] and 0.075" - [16]
  • Split Wire Loom - 1.5"
  • Angle barb - 1/4" - [17]

Firmware

Download firmware: File:Marlin v19.10.CNCTorch.zip

  • To use no temperature sensors, set max temps to 500 and jumper the thermistor pin pairs. Jumpering sets temp to max, which is 358C. Result: does not work. MAXTEMP error is still triggered.
  • So instead in Configuration.h:
  1. define HEATER_0_MINTEMP -1
  2. define BED_MINTEMP -1

This works. Without thermistors, RAMPS reads 0C. Set the minimum below that, and MINTEMP ERROR is avoided.

Build

X axis, carriage, end plug for hanging 1" Universal Axis around 4"x4" stel tube:

Links

Retrieved from "https://wiki.opensourceecology.org/index.php?title=CNC_Torch_Table_v19.10&oldid=204585"