CNC Torch Table v19.10

CAD 1" Universal Axis - 3 Pieces

Mechanical

• 

  Final assembly of CNC torch table. FreeCAD at Gitlab -[1]

• 

  File:YAxisAssembly.FCStd - Assembly of Y axis

• 

  File:Cnctorchidlerassy.fcstd Idler assembly for final assembly via merge workflow.

• 

  File:1inchshaft.fcstd One inch front side shaft.

• 

  608 skateboard 8x22x7 mm Bearing. Download - File:608Bearing.FCStd

• 

  Flange for 608 bearing. Download - File:BearingFlange.FCStd

• 

  Bushing for Flanged bearing. Download - File:BearingBushing.FCStd

• 

  File:Bearing 1in.fcstd

• Torchidlerbolt.png

  Bolt for CNC torch table idler to frame attachment. Download - File:608Bearing.FCStd

• 

  Stock tubing library. Download - File:FreeCAD Tubing Library.tar.gz. See more information at Quarter Inch Stock Tubing

• 

  Parametric 4x4 tubing - File:4x4Tube.FCStd.

• 

  End Plug to join Idler to 4x4 tubing - File:EndPlug.FCStd.

• 

  File:Nema23motor.fcstdNema 23 motor.

• 

  File:CNC Torch 1708 Motor interface.fcstd. STL for printing - File:CNC Torch 1708 motorside.stl

• 

  File:CNC Torch 1in carriage module.fcstd Has the shortened and longer printed piece.

• 

  File:Cnc torch idler v19 10.fcstd Idler with full carriage contact. STL - File:Cnc torch idler v19 10.stl

• 

  File:Torch.fcstd Torch Handle.

• 

  File:Torch tip.fcstd Torch Handle.

• 

  File:Torch handle only.fcstd Torch Handle.

• 

  File:Cnc torch carriage v19 10.fcstd - carriage with nut catchers in top and bottom. STL - File:Cnc torch carriage v19 10.stl

• 

  Peg for 15mm G2 belt - File:Cnc peg 15mm belt v19 10.fcstd - STL - File:Cnc peg 15mm belt v19 10.stl

• 

  File:IdlerShort.FCStd - Short Idler to take flanged bearing

• 

  Half carriage for auto alignment - File:Cnc torch half carriage v19 10.fcstd - STL - File:Cnc torch half carriage v19 10.stl

• 

  Igniter for acetylene cut torch
  FreeCAD - File:Igniter.fcstd

• 

  EM valve for acetylene and oxygen
  FreeCAD - File:Fl 205 cut of solenoid.fcstd

Electronics

• 

  Control Panel - FreeCAD -File:Controlpanel v1904.fcstd. Bent panel STL - File:Bentpanel v1904.stl

• 

  D3D v19.04 Power Supply - FreeCAD -File:Powersupply v1904.fcstd

• 

  RAMPS 1.4 - FreeCAD -File:RAMPS14 v1904.fcstd. Full detailed file - 4MB - [2]

• 

  Stepper driver - FreeCAD -File:Stepperdriver v1904.fcstd. File for detailed LCD controller and endstop can be found at [3]

• 

  Solid state relay - FreeCAD -File:Ssr v1904.fcstd. Source: [4]. See Fotek SSR. Dimensions verified with Amazon source.

• 

  Reprap Discount Smart Controller - FreeCAD -File:Smartcontroller v1904.fcstd. Source: [5].

• 

  Ground Fault Connection Interrupt (GFCI) outlet - FreeCAD -File:Gfci v1904.fcstd. CAD source at McMaster Carr: [6]. May not represent actual GFCI.

• 

  File:Tb6600.fcstd Toshiba 6600 stepper driver. Source: [7]

Concept

edit

BOM

• Impco FL-205-1 valves - [8]
• Impco Et98-52295 valves - [9]
• Brass 90° Elbow 1/4" NPT Male to Female - [10]
• 40 micron Inline Gas Filter - [11][12]
• Idler Bearing - [13]
• Spring steel - 0.049" - [14] and 0.075" - [15]
• Split Wire Loom - 1.5"
• Angle barb - 1/4" - [16]

Firmware

• To use no temperature sensors, set max temps to 500 and jumper the thermistor pin pairs. Jumpering sets temp to max, which is 358C. Result: does not work. MAXTEMP error is still triggered.
• So instead in Configuration.h:

1. define HEATER_0_MINTEMP -1
2. define BED_MINTEMP -1

This works. Without thermistors, RAMPS reads 0C. Set the minimum below that, and MINTEMP ERROR is avoided.

Build

X axis, carriage, end plug for hanging 1" Universal Axis around 4"x4" stel tube:

Links

• Torch Table Genealogy
• Universal Axis
• Universal Controller