D3D v20.04 Software: Difference between revisions
Jump to navigation
Jump to search
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
=Firmware= | =Firmware= | ||
*Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works. | *Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. [[File:Marlin_D3D_Pro_v1.0.zip]] no longer works. | ||
*New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: | *New firmware builds upon the last version with 3-wire endstops - from [[3D Printer Genealogy]] - the first version that had 2-wire endstops was [[D3D v19.02]]. Change log from v19.12 firmware states " Change log: endstop_inverting was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of [[File:Marlin_D3D_Pro_v1.0.zip]] | ||
*'''New file with versioning is thus: [[File:Marlin_D3D_Pro_2.zip]]''' | *'''New file with versioning is thus: [[File:Marlin_D3D_Pro_2.zip]]''' | ||
*Note that we also need to use D3D Universal E steps per mm -M92 E100 | *Note that we also need to use D3D Universal E steps per mm -M92 E100 | ||
*Note we need to make sure we move over 80 mm after G28 so probe is over bed | *Note we need to make sure we move over 80 mm after G28 so probe is over bed | ||
=Updates= | |||
*#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } - changed z from 10 to 30 - increase homing speed. | |||
*#define Z_MAX_POS 400 - increase z | |||
*#define HOMING_FEEDRATE_Z (12*60) - changed this from 4*60 | |||
=Profile= | =Profile= | ||
Latest revision as of 16:28, 26 April 2020
Firmware
- Firmaware goes back from the 2-wire endstops to 3-wire endstops with indicator light to make fabrication easier. File:Marlin D3D Pro v1.0.zip no longer works.
- New firmware builds upon the last version with 3-wire endstops - from 3D Printer Genealogy - the first version that had 2-wire endstops was D3D v19.02. Change log from v19.12 firmware states " Change log: endstop_inverting was reversed on X and Y compared to former versions". Thus, chaning this only would suffice - reversing back to the opposite of File:Marlin D3D Pro v1.0.zip
- New file with versioning is thus: File:Marlin D3D Pro 2.zip
- Note that we also need to use D3D Universal E steps per mm -M92 E100
- Note we need to make sure we move over 80 mm after G28 so probe is over bed
Updates
- define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 } - changed z from 10 to 30 - increase homing speed.
- define Z_MAX_POS 400 - increase z
- define HOMING_FEEDRATE_Z (12*60) - changed this from 4*60
Profile
- File:D3d pro 2.ini
- G0 Z330 takes bed down - but why was it 330 (12"+) in the 8" printers? This is taken from the older printer profiles.