Rototiller/Manufacturing Instructions/Bucket: Difference between revisions
Jump to navigation
Jump to search
| Line 15: | Line 15: | ||
| align="center" |'''QTY.''' | | align="center" |'''QTY.''' | ||
|- | |- | ||
| 1||[[Media:Bucket_-_Blade.PNG| Blade]] ||1 | | 1|| [[Media:Bucket_-_Blade.PNG| Blade]] ||1 | ||
|- | |- | ||
| 2||Skid Plate||2 | | 2|| Skid Plate||2 | ||
|- | |- | ||
| 3||[[media:Bucket_-_Bottom_Plate.PNG| Bottom Plate]] ||1 | | 3|| [[media:Bucket_-_Bottom_Plate.PNG| Bottom Plate]] ||1 | ||
|- | |- | ||
| 4||[[media:Bucket_-_Side Plates.PNG| Side Plates]] ||2 | | 4|| [[media:Bucket_-_Side Plates.PNG| Side Plates]] ||2 | ||
|- | |- | ||
| 5||[[media:Bucket_-_Side_Brace_Plates.PNG| Side Brace Plate]] ||2 | | 5|| [[media:Bucket_-_Side_Brace_Plates.PNG| Side Brace Plate]] ||2 | ||
|- | |- | ||
| 6||Hard Stop Plate||2 | | 6|| [[media:Bucket_-_Hard_Stop_Plate| Hard Stop Plate]] ||2 | ||
|- | |- | ||
| 7||Triangle Plate||2 | | 7|| Triangle Plate||2 | ||
|- | |- | ||
| 8||Cross support plate||1 | | 8|| [[media:Bucket_-_Cross_Support_Plate.PNG| Cross support plate]] ||1 | ||
|- | |- | ||
| 9|| [[media:Bucket_-_Cross_Support_Plate_Lower.PNG| Cross support Plate Lower]] ||1 | | 9|| [[media:Bucket_-_Cross_Support_Plate_Lower.PNG| Cross support Plate Lower]] ||1 | ||
|- | |- | ||
| 10||Rear Mounting Plate||1 | | 10|| [[media:Bucket_-_Rear_Mounting_Plate.PNG| Rear Mounting Plate]] ||1 | ||
|- | |- | ||
| 11||[[media:Bucket_-_Back_Plate.PNG| Back Plate]] ||1 | | 11|| [[media:Bucket_-_Back_Plate.PNG| Back Plate]] ||1 | ||
|- | |- | ||
| 12||[[media:Bucket_-_Bottom_Mounting_Plates.PNG| Bottom Mounting Plates]] ||2 | | 12|| [[media:Bucket_-_Bottom_Mounting_Plates.PNG| Bottom Mounting Plates]] ||2 | ||
|- | |- | ||
| 13||[[media:Bucket_-_Hinge_Pipe.PNG| Hinge Pipe]] ||4 | | 13|| [[media:Bucket_-_Hinge_Pipe.PNG| Hinge Pipe]] ||4 | ||
|- | |- | ||
| 14|| [[media:Bucket_-_Large_Tube.PNG| Large Tube]] ||2 | | 14|| [[media:Bucket_-_Large_Tube.PNG| Large Tube]] ||2 | ||
|- | |- | ||
| 15||Hex Nut, 0.75-10, Steel||4 | | 15|| Hex Nut, 0.75-10, Steel||4 | ||
|- | |- | ||
|} | |} | ||
=Assembly= | =Assembly= | ||
Revision as of 05:09, 17 December 2011
| |||||||||||||||||||
Overview
The bucket is used to collect the dirt as it is chopped up by the spinning tines. It also contains the features that allow the entire assembly to mount to the tractor.
Tools Required
Materials Required
Part Fabrication
| ITEM NO. | PART NAME | QTY. |
| 1 | Blade | 1 |
| 2 | Skid Plate | 2 |
| 3 | Bottom Plate | 1 |
| 4 | Side Plates | 2 |
| 5 | Side Brace Plate | 2 |
| 6 | Hard Stop Plate | 2 |
| 7 | Triangle Plate | 2 |
| 8 | Cross support plate | 1 |
| 9 | Cross support Plate Lower | 1 |
| 10 | Rear Mounting Plate | 1 |
| 11 | Back Plate | 1 |
| 12 | Bottom Mounting Plates | 2 |
| 13 | Hinge Pipe | 4 |
| 14 | Large Tube | 2 |
| 15 | Hex Nut, 0.75-10, Steel | 4 |
