User contributions for Tom Griffing
Jump to navigation
Jump to search
12 December 2011
- 04:4404:44, 12 December 2011 diff hist −4 Power Cube/Manufacturing Instructions No edit summary
- 04:2804:28, 12 December 2011 diff hist −964 Power Cube/Manufacturing Instructions No edit summary
- 04:2704:27, 12 December 2011 diff hist +154 N PowerCube Throttle Created page with "===Throttle Adjustment=== * The engine throttle is adjusted with a push-pull cable as shown in the image below. ::400px" current
- 04:2604:26, 12 December 2011 diff hist +35 Power Cube/Manufacturing Instructions →Assembly
- 04:2504:25, 12 December 2011 diff hist +188 N PowerCube Choke installation Created page with "===Choke installation=== * NOTE: Only necessary if your engine has a manual choke adjustment! * Secure the engine choke knob as shown in the illustration below ::[[image:ChokeBra..." current
- 04:2504:25, 12 December 2011 diff hist +244 N PowerCube Keyswitch and Choke Installation Created page with "===Keyswitch and Choke Installation=== * Install the keyswitches in the brackets and wire as in the wiring illustration below. ::image:KeyswitchWiring.jpg * If your engine ha..." current
- 04:2504:25, 12 December 2011 diff hist +371 N PowerCube Wiring Created page with "===Wiring=== * The keyswitch has spade connectors for wiring and bolts to the frame for stability. These should be connected with matching crimp-on connectors. ::[[Image:keyswit..."
- 04:2404:24, 12 December 2011 diff hist −716 Power Cube/Manufacturing Instructions No edit summary
- 04:2204:22, 12 December 2011 diff hist +164 N PowerCube Install Mufflers Created page with "===Install Mufflers=== * Unscrew the muffler from the elbow joint. * Bolt the elbow / flange to the engine. * Screw the muffler once again into the elbow joint." current
- 04:2104:21, 12 December 2011 diff hist +72 N PowerCube Install Solenoid Created page with "===Install Solenoid=== * Secure the solenoid on the bolts with two nuts." current
- 04:2104:21, 12 December 2011 diff hist +639 N PowerCube Install Hydraulic Components Created page with "===Install Hydraulic Components=== * Install hydraulic suction filter in tank and hose barb in suction filter * Connect one end of suction hose to strainer hose barb, the other e..."
- 04:2004:20, 12 December 2011 diff hist −466 Power Cube/Manufacturing Instructions No edit summary
- 04:1804:18, 12 December 2011 diff hist +325 N PowerCube Finish and Painting Created page with "===Finish and Painting=== * Remove the engine if present * Cover holes of tanks and any other place that should not be painted. * Check all external surfaces for sharp edges and ..." current
- 04:1804:18, 12 December 2011 diff hist +137 N PowerCube Solenoid Mounting Bolts Created page with "===Solenoid Mounting Bolts=== * Weld the solenoid mounting bolts to the hydraulic reservoir as shown below. ::image:SolenoidMount.jpg" current
- 04:1704:17, 12 December 2011 diff hist +172 N PowerCube Keyswtich and Choke Brackets Created page with "===Keyswtich and Choke Brackets=== * Clamp the keyswitch bracket to the frame as shown and weld in place. * Clamp the choke bracket to the frame as shown and weld in place." current
- 04:1704:17, 12 December 2011 diff hist −1,455 Power Cube/Manufacturing Instructions No edit summary
- 04:1504:15, 12 December 2011 diff hist +1,076 N PowerCube Oil cooler and fan mounts Created page with "===Oil cooler and fan mounts=== *Position the two ¼” x 2” x 22” plates to the outside of the frame, adjust so the oil cooler mounting bolts match the holes in the plates a..." current
- 04:1504:15, 12 December 2011 diff hist +305 N PowerCube Quick Attach Plates Created page with "===Quick Attach Plates=== *Weld the [2] 3/8” x 4” x 27” plates to the top sides of the frame as shown. Secure at 45 degree angles before welding in place. Use solid, stro..."
- 04:1204:12, 12 December 2011 diff hist +262 N PowerCube Battery mount Created page with "===Battery mount=== *Weld the two mounts to the angle iron and tank to form a rectangle for the battery as shown below. ::Image:PowerCubeAssemblyBatteryMount1.png *After th..."
- 04:1104:11, 12 December 2011 diff hist −5,881 Power Cube/Manufacturing Instructions No edit summary
- 04:0904:09, 12 December 2011 diff hist +3,604 N PowerCube Engine Mounts and Hydraulic Motor Mount Created page with "===Engine Mounts and Hydraulic Motor Mount=== See Power Cube Tank Welding Procedure Then review assembly order: ::{{YoutubePopup|uuXWTjWEgu8|big|powercube-window}} *Plac..." current
- 04:0904:09, 12 December 2011 diff hist +639 N PowerCube Hydraulic tank Created page with "===Hydraulic tank=== *Perform a “soap bubble” test on the tank by securely covering the larger hole (use something like strong tape), pressurizing the tank using the smaller..." current
- 04:0804:08, 12 December 2011 diff hist +825 N PowerCube Gas tank Created page with "===Gas tank=== *Screw the 1/4" hose barb into the 1/4 NPT flange welded into the gas tank. *Perform a “soap bubble” test on the tank. Securely cover the larger hole (use so..." current
- 04:0804:08, 12 December 2011 diff hist +972 N PowerCube Frame Created page with "===Power Cube Frame=== *Position two ¼” x 2” x 2” x 29” pieces angle iron on top of two 27” angle pieces as shown below. Check that all joints are square, then tack a..."
- 04:0704:07, 12 December 2011 diff hist +200 Power Cube/Manufacturing Instructions No edit summary
- 04:0204:02, 12 December 2011 diff hist −4 Power Cube/Manufacturing Instructions →Subassembly Fabrication
- 04:0104:01, 12 December 2011 diff hist −5,152 Power Cube/Manufacturing Instructions →Subassembly Fabrication
- 03:5903:59, 12 December 2011 diff hist +1,463 N PowerCube Hydraulic reservoir Created page with "====Hydraulic reservoir==== *[2] ¼” x 6” x 12” *6” x 12” x 27 ½” Tube *2” x 2 ¼” x 1/8” Tube '''Clean tank components prior to welding''' *Clean tank edges..."
- 03:5903:59, 12 December 2011 diff hist +914 N PowerCube Mufflers Created page with "====Mufflers==== * [2] Galvanized Muffler Pipe Tube 1 1/2” 1/8” 6” * [2] Galvanized Muffler Pipe Tube 6 cm 1/8” 7” * [2] Galvanized Steel round 1 1/2" * [4] Galvanized..."
- 03:5803:58, 12 December 2011 diff hist +228 N PowerCube Battery Mount Created page with "====Battery Mount==== *[2] ¼” x 2” x 2” x 4 3/4” Angle *[2] ¼” x 2” x 5/8” Plate ::400px Cut pieces on bandsaw or metal cutoff saw. ..." current
- 03:5803:58, 12 December 2011 diff hist +478 N PowerCube Electrical cables Created page with "=====Electrical cables===== *Note: The connectors can be purchased from an auto parts store – be aware that they usually require a crimper to attach to the cables. Alternative..."
- 03:5603:56, 12 December 2011 diff hist +306 N PowerCube Key Switches and Choke Created page with "=====Key Switches and Choke===== ::thumb|Key switch label with OEM part number. Key switch mount location: on hydraulic tank side. *[3] 1/8” x 2..." current
- 03:5603:56, 12 December 2011 diff hist +505 N PowerCube Oil Cooler Mount Created page with "=====Oil Cooler Mount===== *[2] ¼” x 2” x 24” Plates **This is fan mount, not cooler mount. Holes in fan mount are missing. Length should be 23", not 24" -MJ *[2] ¼” x ..."
- 03:5503:55, 12 December 2011 diff hist +661 N PowerCube Fuel tank Created page with "=====Fuel tank===== *[2] ¼” x 4” x 8” Plates *4” x 8” x 14 ½” Tube *¼” x 2” x 24” Plate * All welds assembling the tank must be quality welds, as they must..."
- 03:5503:55, 12 December 2011 diff hist +103 N PowerCube Quick attach mounts Created page with "=====Quick attach mounts===== *[2] 3/8” x 4” x 27” Plates ::200px"
- 03:5403:54, 12 December 2011 diff hist +474 N PowerCube Engine & Hydraulic Pump mounts Created page with "===Engine & Hydraulic Pump mounts=== * ¼” x 8” x 12” Plate * ¼” x 8” x 9” Plate * ¼” x 2” x 2” x 8” Angle * ¼” x 2” x 2” x 29” Angle * ¼” x 8..."
- 03:5303:53, 12 December 2011 diff hist +252 Power Cube/Manufacturing Instructions →Subassembly Fabrication
- 03:5103:51, 12 December 2011 diff hist +23 Power Cube/Manufacturing Instructions →Preparation
- 03:4903:49, 12 December 2011 diff hist +219 Power Cube/Manufacturing Instructions No edit summary
- 03:4203:42, 12 December 2011 diff hist −787 Power Cube/Manufacturing Instructions No edit summary
- 03:4003:40, 12 December 2011 diff hist +196 N PowerCube Tools Created page with "===Tools=== *Welder *Angle Grinder *Hand Tools **Crescent wrench **Socket set **Hammer *Metal Cutting Tools **Bandsaw **Chopsaw **Torch *Paint Tools **Gravity Fed Paint Spraye..."
- 03:4003:40, 12 December 2011 diff hist +480 N PowerCube Workspace Created page with "===Workspace=== This section describes the various workspace areas that we have found to be useful in fabricating the Power Cube. It is provided as a suggestion for preparing y..."
- 03:3903:39, 12 December 2011 diff hist +105 N PowerCube Safety Created page with "===Safety=== *Hearing Protection *Eye Protection *Steel Toe Boots *Welding **Gloves **Hood **Apron/Jacket"
- 03:3903:39, 12 December 2011 diff hist +30 Power Cube/Manufacturing Instructions →Preparation
- 03:3703:37, 12 December 2011 diff hist +12 Power Cube/Manufacturing Instructions No edit summary
- 03:3703:37, 12 December 2011 diff hist +30 Power Cube/Manufacturing Instructions No edit summary
6 December 2011
- 05:1105:11, 6 December 2011 diff hist +250 Fuel Tank →New Fuel Tank
5 December 2011
- 12:5312:53, 5 December 2011 diff hist +5 Fuel Tank →New Fuel Tank
- 12:5312:53, 5 December 2011 diff hist +612 m Fuel Tank No edit summary
- 12:2112:21, 5 December 2011 diff hist +120 Fuel Tank →Current Design