Industrial Robot/Manufacturing Instructions

---

Tooling and Infrastructure

Measuring and Marking

• Scriber

• Metal Rule

• Combination Set

• Center Punch

Taps and Dies

• 1/2" - 13 Taps

• 9/16" - 18 Taps

• Tap Wrench

Port Cutting

• SAE6 Port Contour Cutter

Drilling

• Cordless Drill

Twist Drill Bits

• 1/2"

• 3/8"

• 1/4"

• 5/32"

• 1/8"

Soldering

• Soldering Iron and Stand

• Solder

Torching

• Oxy-acetylene Torch

Turning

• Lathe

• Cutting tools - turning, grooving

Hand Tools

• Adjustable pliers

• File

Fabrication

Foundation

• The foundation can be a large tube that is flanged at both ends; one flange is fastened to the ground while the other is fastened to the axis 1 slewing bearing.

• Alternatively, the foundation can be a plate that is fastened at its corners to the ground. On top of this ground-mounted plate, 4 upright pillars are welded or fastened; then, another plate is fastened upon these pillars then fastened again to the axis 1 slewing bearing.

• Alternatively, the foundation can be two long square tubes that are fastened to the ground parallel and at a sizeable distance from each other. Then two more square tubes, parallel to each other but perpendicular to the first two tubes, are fastened on top of the first two tubes. Upright square bars are fastened to the intersections of the first and second tubes, making that 4 bars in total, being 1 to each intersection. A plate is fastened on top of these bars then fastened again to the axis 1 slewing bearing.

Base

• The base can be comprised of an angle that partially fastens to the axis 1 slewing bearing and axis 2 slewing bearing. This angle also would allow mounting of the axis 1 hydraulic motor and axis 2 hydraulic motor, as well as the axis 1 encoder and the axis 2 encoder.

• Alternatively, the base can be comprised of a plate that completely fastens to the axis 1 slewing bearing and another plate that completely fastens to the axis 2 slewing bearing. Then an angle fastens to the aforementioned 2 plates; this angle also would allow mounting of the axis 1 hydraulic motor and axis 2 hydraulic motor, as well as the axis 1 encoder and the axis 2 encoder.

Base-to-Mid

• The base-to-mid can be comprised of a large bar that is partially fastened to the axis 2 slewing bearing and axis 3 slewing bearing.

• Alternatively, the base-to-mid can be a plate that is completely fastened to the axis 2 slewing bearing and another plate that is completely fastened to the axis 3 slewing bearing. Then, these two plates would be fastened to the ends of a large bar.

Mid

• Same as for "Base" except with the axis 3 and axis 4 slewing bearings, hydraulic motors, and encoders.

Mid-to-End

• The mid-to-end can consist of a plate completely fastened to the axis 4 slewing bearing. The center of this plate can be welded to the end of a large square tube, the combination being perpendicular like a T. At the other end of the tube, a plate can be welded in parallel. This second plate would be completely fastened to the axis 5 slewing bearing.

End

Same as for "Base" except with the axis 5 and axis 6 slewing bearings, hydraulic motors, and encoders.

Stepper Mount

[6] Stepper Motor Mount Angle

• • Mark cuts with scriber and try-square
  • Cut with torch cutter
  • Mark holes with scriber, rule, try-square, and center punch
  • Drill holes with 1" bit, 1/4" bit, 1/8" bit, and cordless drill

Media:StepperMotorMountAngle.jpg

[6] Stepper Motor Mount Plate

• • Mark cuts with scriber and try-square
  • Cut with torch cutter
  • Mark holes with scriber, rule, try-square, and center punch
  • Drill holes with 1/4" bit and cordless drill

Media:StepperMotorMountPlate.jpg

[6] Shaft Coupling

• • Mark cuts with scriber and box-square
  • Cut with torch cutter
  • Mark thru hole with scriber, combination set, and center punch
  • Drill holes with 1/2" bit, 1/4" bit, 5/32" bit, and cordless drill
  • Tap holes with 10-24 taper/intermediate/plug taps and tap wrench

Media:ShaftBar.jpg

Assembly

Assemble Stepper Motor Mount

• As shown below, repeat for a total of 6 mounts

Media:Stepneedlemount.jpg

• Solder PWM driver Instructions

The Global Village Construction Set
Habitat	CEB Press	Cement Mixer	Sawmill	Bulldozer	Backhoe
Agriculture	Tractor	Seeder	Hay Rake	Well-Drilling Rig
	Microtractor	Soil Pulverizer	Spader	Hay Cutter	Trencher
	Bakery Oven	Dairy Milker	Microcombine	Baler
Industry	Multimachine	Ironworker	Laser Cutter	Welder	Plasma Cutter
	CNC Torch Table	Metal Roller	Rod and Wire Mill	Press Forge	Universal Rotor
	3D Printer	3D Scanner	CNC Circuit Mill	Industrial Robot	Chipper Hammermill
	Drill Press	Induction Furnace
Energy	Power Cube	Gasifier Burner	Solar Concentrator	Electric Motor Generator	Hydraulic Motor
	Steam Engine	Heat Exchanger	Wind Turbine	Pelletizer	Universal Power Supply
	Nickel-Iron Battery
Materials	Aluminum Extractor	Bioplastic Extruder
Transportation	Car	Truck
Key	Design	Planning	Prototype	Almost done	Full Release